![]() |
Code of Federal Regulations (Last Updated: July 5, 2024) |
![]() |
Title 29 - Labor |
![]() |
Subtitle B - Regulations Relating to Labor |
![]() |
Chapter XVII - Occupational Safety and Health Administration, Department of Labor |
![]() |
Part 1928 - Occupational Safety and Health Standards for Agriculture |
![]() |
Subpart C - Roll-Over Protective Structures |
§ 1928.51 - Roll-over protective structures (ROPS) for tractors used in agricultural operations.
-
§ 1928.51 Roll-over protective structures (ROPS) for tractors used in agricultural operations.
(a) Definitions. As used in this subpart -
Agricultural tractor means a two-or four-wheel drive type vehicle, or track vehicle, of more than 20 engine horsepower, designed to furnish the power to pull, carry, propel, or drive implements that are designed for agriculture. All self-propelled implements are excluded.
Low profile tractor means a wheeled tractor possessing the following characteristics:
(1) The front wheel spacing is equal to the rear wheel spacing, as measured from the centerline of each right wheel to the centerline of the corresponding left wheel.
(2) The clearance from the bottom of the tractor chassis to the ground does not exceed 18 inches.
(3) The highest point of the hood does not exceed 60 inches, and
(4) The tractor is designed so that the operator straddles the transmission when seated.
Tractor weight includes the protective frame or enclosure, all fuels, and other components required for normal use of the tractor. Ballast shall be added as necessary to achieve a minimum total weight of 110 lb. (50.0 kg.) per maximum power take-off horsepower at the rated engine speed or the maximum gross vehicle weight specified by the manufacturer, whichever is the greatest. Front end weight shall be at least 25 percent of the tractor test weight. In case power take-off horsepower is not available, 95 percent of net engine flywheel horsepower shall be used.
(b) General requirements. Agricultural tractors manufactured after October 25, 1976, shall meet the following requirements:
(1) Roll-over protective structures (ROPS). ROPS shall be provided by the employer for each tractor operated by an employee. Except as provided in paragraph (b)(5) of this section, a ROPS used on wheel-type tractors shall meet the test and performance requirements of 29 CFR 1928.52, 1928.53, or 1926.1002 as appropriate. A ROPS used on track-type tractors shall meet the test and performance requirements of 29 CFR 1926.1001.
(2) Seatbelts.
(i) Where ROPS are required by this section, the employer shall:
(A) Provide each tractor with a seatbelt which meets the requirements of this paragraph;
(B) Ensure that each employee uses such seatbelt while the tractor is moving; and
(C) Ensure that each employee tightens the seatbelt sufficiently to confine the employee to the protected area provided by the ROPS.
(ii) Each seatbelt shall meet the requirements set forth in Society of Automotive Engineers Standard SAE J4C, 1965 Motor Vehicle Seat Belt Assemblies,[2] except as noted hereafter:
(A) Where a suspended seat is used, the seatbelt shall be fastened to the movable portion of the seat to accommodate a ride motion of the operator.
(B) The seatbelt anchorage shall be capable of withstanding a static tensile load of 1,000 pounds (453.6 kg) at 45 degrees to the horizontal equally divided between the anchorages. The seat mounting shall be capable of withstanding this load plus a load equal to four times the weight of all applicable seat components applied at 45 degrees to the horizontal in a forward and upward direction. In addition, the seat mounting shall be capable of withstanding a 500 pound (226.8 kg) belt load plus two times the weight of all applicable seat components both applied at 45 degrees to the horizontal in and upward and rearward direction. Floor and seat deformation is acceptable provided there is not structural failure or release of the seat adjusted mechanism or other locking device.
(C) The seatbelt webbing material shall have a resistance to acids, alkalies, mildew, aging, moisture, and sunlight equal to or better than that of untreated polyester fiber.
(3) Protection from spillage. Batteries, fuel tanks, oil reservoirs, and coolant systems shall be constructed and located or sealed to assure that spillage will not occur which may come in contact with the operator in the event of an upset.
(4) Protection from sharp surfaces. All sharp edges and corners at the operator's station shall be designed to minimize operator injury in the event of an upset.
(5) Exempted uses. Paragraphs (b)(1) and (b)(2) of this section do not apply to the following uses:
(i) Low profile tractors while they are used in orchards, vineyards or hop yards where the vertical clearance requirements would substantially interfere with normal operations, and while their use is incidental to the work performed therein.
(ii) Low profile tractors while used inside a farm building or greenhouse in which the vertical clearance is insufficient to allow a ROPS equipped tractor to operate, and while their use is incidental to the work performed therein.
(iii) Tractors while used with mounted equipment which is incompatible with ROPS (e.g. cornpickers, cotton strippers, vegetable pickers and fruit harvesters).
(6) Remounting. Where ROPS are removed for any reason, they shall be remounted so as to meet the requirements of this paragraph.
(c) Labeling. Each ROPS shall have a label, permanently affixed to the structure, which states:
(1) Manufacturer's or fabricator's name and address;
(2) ROPS model number, if any;
(3) Tractor makes, models, or series numbers that the structure is designed to fit; and
(4) That the ROPS model was tested in accordance with the requirements of this subpart.
(d) Operating instructions. Every employee who operates an agricultural tractor shall be informed of the operating practices contained in appendix A of this part and of any other practices dictated by the work environment. Such information shall be provided at the time of initial assignment and at least annually thereafter.
[40 FR 18257, Apr. 25, 1975, as amended at 61 FR 9255, Mar. 7, 1996; 69 FR 18803, Apr. 9, 2004; 70 FR 77003, Dec. 29, 2005]