§ 90.114 - Requirement of certification - engine information label.  


Latest version.
  • § 90.114 Requirement of certification - engine information label.

    (a) The engine manufacturer must affix at the time of manufacture a permanent and legible label identifying each nonroad engine. The label must meet the following requirements:

    (1) Be attached in such a manner that it cannot be removed without destroying or defacing the label;

    (2) Be durable and readable for the entire engine life;

    (3) Be secured to an engine part necessary for normal engine operation and not normally requiring replacement during engine life;

    (4) Be written in English; and

    (5) Be located so as to be readily visible to the average person after the engine is installed in the vehicle.

    (b) If the nonroad vehicle obscures the label on the engine, the nonroad vehicle manufacturer must attach a supplemental label so that this label is readily visible to the average person. The supplemental label must:

    (1) Be attached in such a manner that it cannot be removed without destroying or defacing the label;

    (2) Be secured to a vehicle part necessary for normal operation and not normally requiring replacement during the vehicle life; and

    (3) Be identical in content to the label which was obscured.

    (c) The label must contain the following information:

    (1) The heading “Important Engine Information;”

    (2) The full corporate name and trademark of the engine manufacturer;

    (3) The statement, “This (specify vehicle or engine, as applicable) is certified to operate on (specify operating fuel(s));”

    (4) Identification of the Exhaust Emission Control System (Abbreviations may be used and must conform to the nomenclature and abbreviations provided in the Society of Automotive Engineers procedure J1930, “Electrical/Electronic Systems Diagnostic Terms, Definitions, Abbreviations and Acronyms,” September 1991. This procedure has been incorporated by reference. See § 90.7.);

    (5) All engine lubricant requirements;

    (6) Date of engine manufacture [day (optional), month and year];

    (7) The statement “THIS ENGINE CONFORMS TO U.S. EPA REGS FOR [MODEL YEAR].”;

    (8) EPA standardized engine family designation;

    (9) Engine displacement [in cubic centimeters];

    (10) Other information concerning proper maintenance and use or indicating compliance or noncompliance with other standards may be indicated on the label;

    (11) For Phase 2 engines, the useful life category as determined by the manufacturer pursuant to § 90.105. Such useful life category shall be shown by one of the following statements to be appended to the statement required under paragraph (c)(7) of this section:

    (i) “EMISSIONS COMPLIANCE PERIOD: [useful life] HOURS”; or

    (ii) “EMISSIONS COMPLIANCE PERIOD: CATEGORY [fill in C, B or A as indicated and appropriate from the tables in § 90.105], REFER TO OWNER'S MANUAL FOR FURTHER INFORMATION”;

    (d) If there is insufficient space on the engine (or on the vehicle where a supplemental label is required under paragraph (b) of this section) to accommodate a label including all the information required in paragraph (c) of this section, the manufacturer may delete or alter the label as indicated in this paragraph. The information deleted from the label must appear in the owner's manual.

    (1) Exclude the information required in paragraphs (c)(3), (4), and (5) of this section. The fuel or lubricant may be specified elsewhere on the engine.

    (2) Exclude the information required by paragraph (c)(6) of this section, if the date the engine was manufactured is stamped on the engine.

    (e) The Administrator may, upon request, waive or modify the label content requirements of paragraphs (c) and (d) of this section, provided that the intent of such requirements is met.

    (f) Manufacturers electing to use the labeling language of paragraph (c)(11)(ii) of this section must provide in the documents intended to be conveyed to the ultimate purchaser, the statement:

    (1) For nonhandheld engines: The Emissions Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements. For engines less than 66 cc, Category C = 50 hours, B = 125 hours, and A = 300 hours. For engines equal to or greater than 66 cc but less than 225 cc displacement, Category C = 125 hours, B = 250 hours, and A = 500 hours. For engines of 225 cc or more, Category C = 250 hours, B = 500 hours, and A = 1000 hours.

    (2) For handheld engines: The Emissions Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements. Category C = 50 hours, B = 125 hours, and A = 300 hours.

    (3) The manufacturer must provide, in the same document as the statement in paragraph (f)(1) or (f)(2) of this section, a statement of the engine's displacement or an explanation of how to readily determine the engine's displacement. The Administrator may approve alternate language to the statement in paragraph (f)(1) or (f)(2) of this section, provided that the alternate language provides the ultimate purchaser with a clear description of the number of hours represented by each of the three letter categories for the subject engine's displacement.

    (g) Manufacturers may add appropriate features to prevent counterfeit labels. For example, manufacturers may include the engine's unique identification number on the label.

    [60 FR 34598, July 3, 1995, as amended at 64 FR 15239, Mar. 30, 1999; 65 FR 24307, Apr. 25, 2000; 73 FR 3613, Jan. 18, 2008; 73 FR 59180, Oct. 8, 2008]