[Federal Register Volume 61, Number 126 (Friday, June 28, 1996)]
[Rules and Regulations]
[Pages 33680-33691]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 96-16540]
-----------------------------------------------------------------------
ENVIRONMENTAL PROTECTION AGENCY
40 CFR Parts 148 and 268
[EPA # F-96-PH3F-FFFFF; FRL-5528-1]
RIN 2050-AD38
Land Disposal Restrictions Phase III--Decharacterized
Wastewaters, Carbamate Wastes, and Spent Potliners
AGENCY: Environmental Protection Agency (EPA).
ACTION: Technical correction.
-----------------------------------------------------------------------
SUMMARY: On April 8, 1996, EPA published regulations covering both
congressionally-mandated and court-ordered prohibitions on land
disposal of certain hazardous wastes. On the same day, EPA published a
partial withdrawal and correction of those regulations to the extent
the Land Disposal Program Flexibility Act (LDPFA) (signed by the
President on March 26, 1996) revoked most of the court-ordered
prohibitions. This notice corrects technical errors in the final
regulations and the partial withdrawal notice.
EFFECTIVE DATE: This rule is effective on June 28, 1996.
ADDRESSES: Supporting materials are available for viewing in the RCRA
Information Center (RIC), located at Crystal Gateway One, 1235
Jefferson Davis Highway, First Floor, Arlington, VA. The Docket
Identification Number is F-96-PH3F-FFFFF. The RCRA Docket is open from
9 a.m. to 4 p.m. Monday through Friday, except for Federal holidays.
The public must make an appointment to review docket materials by
calling (703) 603-9230. The public may copy a maximum of 100 pages from
any regulatory document at no cost. Additional copies cost $0.15 per
page.
FOR FURTHER INFORMATION CONTACT: For general information contact the
RCRA Hotline at (800) 424-9346 (toll free) or (703) 920-9810 in the
Washington, DC metropolitan area. For information on this notice
contact Michael Petruska (5302W), Office of Solid Waste, 401 M Street,
S.W., Washington, DC 20460, (703) 308-8434.
SUPPLEMENTARY INFORMATION:
I. Reasons and Basis for Today's Amendment
The Agency has received comments from the regulated community and
State agencies requesting clarification on certain aspects of the April
8, 1996 Land Disposal Restrictions (LDR) Phase III final rule (61 FR
15566) and the April 8, 1996 withdrawal notice (61 FR 15660). Today's
amendment responds to these comments and makes technical corrections
where appropriate.
II. Amendments to the LDR Phase III Final Rule
There were several errors in the treatment standard table in
Sec. 268.40, and in the table of Universal Treatment Standards (UTS) in
Sec. 268.48. The errors pertained to portions of the final rule which
were not affected by the LDPFA. It should be noted that certain errors
in both of these tables are not being corrected here as they are being
corrected by the Office of Federal Register.
A. Section 268.40 Table
There were several errors in the table ``Treatment Standards for
Hazardous
[[Page 33681]]
Waste'' in section 268.40. First, the waste codes for the proposed
organobromine wastes--K140 and U404--inadvertently appeared in the
table. As was explained in the preamble to the final rule (61 FR 15566,
15569, April 8, 1996), however, the Agency is not promulgating
treatment standards for these wastes at this time since the listing of
these wastes as hazardous has not been finalized. Today's notice
removes these entries from the table.
Second, the treatment standards set out in the table for the
carbamate wastes were incorrect. These entries reflected the waste
codes and constituents in the proposed listing instead of the waste
codes and constituents in the finalized listing (60 FR 7824, February
9, 1995). These entries also are being corrected in today's notice.
Third, the entries for F006, F007, F010, F037, F039, K006, and K062
included treatment standards for constituents for which previously
there was no standard (``NA'' had appeared instead). The proposed rule
had included treatment standards to replace all of the ``NA'' entries
in the table. However, as was explained in the preamble to the final
rule (61 FR at 15569), the Agency agreed with commenters who felt it
was arbitrary to add a standard for the sake of completeness where
previously there was none, and, therefore, the Agency did not finalize
the proposed changes. However, EPA inadvertently continued to include
the standard for these waste codes in the final rule. Today's notice
restores the ``NA'' entries.
B. Section 268.48 Table
The wastewater treatment standards for A2213, Butylate, Cycloate,
EPTC, Molinate, Pebulate, Prosulfocarb, Triallate, and Vernolate
appeared in the table of UTS as 0.003, although the preamble gave the
correct standard as 0.042 (61 FR 15584). Today's notice corrects the
UTS table.
III. Amendments to the LDR Phase III Withdrawal Notice
There are four sections in the withdrawal notice that need
correction/clarification--Secs. 148.1, 268.1, 268.3, and 268.40.
A. Section 148.1
The Agency today is amending the language in Sec. 148.1(d) to more
accurately reflect the recently enacted LDPFA. The revised language
clarifies that decharacterized wastes injected in any Class I injection
well--either hazardous or nonhazardous--are not prohibited wastes, and,
therefore, are not subject to the Land Disposal Restrictions (LDR)
treatment standards. This result was alluded to in the April 8, 1996
withdrawal notice (61 FR 15661), but the Agency believes it is
appropriate to further make it clear that both hazardous and
nonhazardous Class I wells are excepted, as provided in the text of the
legislation.
B. Section 268.1
The Agency also is amending the language in Sec. 268.1(c) to mirror
the amended language in Sec. 148.1(d) described above. We also are
clarifying that decharacterized wastewaters managed in Clean Water Act
(CWA) or equivalent systems with land disposal units are not prohibited
wastes, and, thus, are not subject to LDR treatment standards. As
provided in the legislation, the decharacterized wastes managed in CWA
or CWA-equivalent systems which remain prohibited are those that have a
specified ``method of treatment'' for a treatment standard, or are
reactive cyanide wastes. This clarification was also alluded to in the
April 8, 1996 withdrawal notice (61 FR 15661).
C. Section 268.3
The Agency is today amending the dilution prohibition language in
Sec. 268.3(b) to clarify that the treatment method of deactivation
(DEACT) is not considered a specified method of treatment for the
purposes of that section. This change merely codifies existing Agency
interpretation (see preamble discussion at 55 FR 22666, June 1, 1990;
and 57 FR 8087-8088, March 6, 1992).
D. Section 268.40
As discussed in A. and B. of this section, decharacterized wastes
managed in CWA or CWA-equivalent systems (with land disposal units
receiving the decharacterized waste) are no longer prohibited wastes,
with the exception of characteristic wastes that have a specified
method as a treatment standard and reactive cyanide. All
decharacterized wastes injected into Class I wells also are no longer
prohibited wastes.
In the rush of preparing a notice to reflect the new legislation as
quickly as possible, EPA inadvertently failed to remove the numerical
standards for these categories of wastes and replace them with the
characteristic level (61 FR at 15664-15668). Therefore, the treatment
standards in the April 8 withdrawal notice for these wastes were in
error. For instance, the wastewater treatment standard for benzene in
D018 wastes that are managed in CWA, CWA equivalent, or Class I
injection wells was given as 0.14 mg/l. In fact, a D018 wastewater
managed in one of these systems need only meet the regulatory level of
0.5 mg/l to be rendered nonhazardous (i.e. decharacterized) and, hence,
no longer prohibited. Today's notice corrects this mistake by removing
that category from the table of Treatment Standards for Hazardous
Wastes, and indicating via a footnote that these wastes, once
decharacterized, are no longer subject to LDR treatment standards.
The Agency wishes to clarify further that these non-LDR wastes also
are not subject to the LDR notification and certification requirements
of Sec. 268.7 and Sec. 268.9.
IV. Clarification to the Phase III Withdrawal Notice
Under RCRA regulations in effect before the LDPFA, wastes that are
listed solely because they exhibit a hazardous characteristic are not
prohibited from land disposal if they are managed in CWA, CWA-
equivalent, or Class I injection well systems and are no longer
hazardous at the point of land disposal. Id.; see also the codification
of this principle at 40 CFR 261.3(a)(2)(iii) and 57 FR at 37210-211
(August 18, 1992). (The exception is for listed wastes that are subject
to a method of treatment; these wastes cannot be disposed of in CWA or
equivalent systems. See 55 FR at 22656, 22657 (general principle in
Third Third final rule that characteristic wastes subject to a method
of treatment remain subject to dilution prohibition even when managed
in CWA treatment systems) and 57 FR 37210 (same principle should apply
to wastes listed solely because they exhibit a characteristic).
In the April 8, 1996 withdrawal notice, EPA stated that it would
not, at least for the time being, reopen those land disposal
restriction rules applicable to wastes listed solely because they
exhibit a hazardous waste characteristic (e.g. U002 commercial chemical
product acetone). See 61 FR at 15661-62. This is because the new
legislation does not directly apply to such wastes. Id.
EPA is taking this opportunity to clarify that the existing rules
on wastes listed solely because they exhibit a characteristic apply to
all wastes, regardless of whether they are wastewaters or non-
wastewaters, so long as they are managed in the prescribed types of
wastewater management systems. Notwithstanding unclear language in the
August, 1992 preamble cited above, what the Agency intended to do was
to put wastes listed solely because they exhibit a characteristic on
[[Page 33682]]
the same footing vis-a-vis the dilution prohibition as the
characteristic wastes covered by the Third Third rule. 57 FR at 37210.
Under that Third Third rule, most characteristic wastes (whether or not
they were in the wastewater or nonwastewater treatability group) could
be permissibly be managed in CWA systems and Class I UIC injection
wells so long as they were rendered non-hazardous by any means before
being placed in a land disposal unit (i.e. surface impoundment or Class
I injection well). 55 FR at 22656-658 (June 1, 1990). EPA is formally
clarifying this point by means of today's preamble discussion.
V. Rationale for Immediate Effective Date
Today's notice does not create any new regulatory requirements;
rather, it restates and clarifies requirements already in effect (by
virtue of the new legislation) by correcting a number of errors in the
April 8, 1996 final rule and withdrawal notice. For these reasons, EPA
finds that good cause exists under section 3010(b)(3) of RCRA, 42
U.S.C. 9903(b)(3), to provide for an immediate effective date. See
generally 61 FR at 15662. For the same reasons, EPA finds that there is
good cause under 5 U.S.C. 553(b)(3) to promulgate today's corrections
in final form and that there is good cause under 5 U.S.C. 553(b)(3) to
waive the requirement that regulations be published at least 30 days
before they become effective.
VI. Analysis Under Executive Order 12866, the Unfunded Mandates Reform
Act of 1995, the Regulatory Flexibility Act, and the Paperwork
Reduction Act
This technical correction does not create any new regulatory
requirements. It merely corrects technical errors and clarifies
requirements already in effect (by virtue of the new legislation) and
therefore is not a ``significant'' regulatory action within the meaning
of Executive Order 12866, and does not impose any Federal mandate on
State, local, or tribal governments or the private sector within the
meaning of the Unfunded Mandates Reform Act of 1995. For the same
reasons, pursuant to the Regulatory Flexibility Act, I certify that
this action would not have a significant impact on a substantial number
of small entities. Finally, because this is a technical correction, it
does not affect requirements under the Paperwork Reduction Act.
VII. Submission to Congress and the General Accounting Office
Under section 801(a)(1)(A) of the Administrative Procedure Act
(APA) as amended by the Small Business Regulatory Enforcement Fairness
Act of 1996, EPA submitted a report containing this rule and other
required information to the U.S. Senate, the U.S. House of
Representatives and the Comptroller General of the General Accounting
Office prior to publication of the rule in today's Federal Register.
This rule is not a ``major rule'' as defined by section 804(2) of the
APA as amended.
List of Subjects
40 CFR Part 148
Environmental protection, Administrative practice and procedure,
Hazardous waste, Reporting and recordkeeping requirements, Water
supply.
40 CFR Part 268
Hazardous waste, Reporting and recordkeeping requirements.
Dated: June 21, 1996.
Elliott Laws,
Assistant Administrator, Office of Solid Waste and Emergency Response.
For the reasons set forth in the preamble, title 40, chapter I of
the Code of Federal Regulations is amended as follows:
PART 148--HAZARDOUS WASTE INJECTION RESTRICTIONS
1. The authority citation for part 148 continues to read as
follows:
Authority: Secs. 3004, Resource Conservation and Recovery Act,
42 U.S.C. 6901, et seq.
2. Section 148.1 is amended by revising paragraph (d) to read as
follows:
Sec. 148.1 Purpose, scope and applicability.
* * * * *
(d) Wastes that are hazardous only because they exhibit a hazardous
characteristic, and which are otherwise prohibited under this part, or
part 268 of this chapter, are not prohibited if the wastes:
(1) Are disposed into a nonhazardous or hazardous injection well as
defined under 40 CFR Sec. 146.6(a); and
(2) Do not exhibit any prohibited characteristic of hazardous waste
identified in 40 CFR part 261, subpart C at the point of injection.
PART 268--LAND DISPOSAL RESTRICTIONS
3. The authority citation for part 268 continues to read as
follows:
Authority: 42 U.S.C. 6905, 6912(a), 6921, and 6924.
Subpart A--General
4. In section 268.1, paragraph (c) is amended by adding paragraphs
(3) and (4) to read as follows:
Sec. 268.1 Purpose, scope and applicability.
* * * * *
(c) * * *
(3) Wastes that are hazardous only because they exhibit a hazardous
characteristic, and which are otherwise prohibited under this part, or
part 148 of this chapter, are not prohibited if the wastes:
(i) Are disposed into a nonhazardous or hazardous injection well as
defined under 40 CFR 146.6(a); and
(ii) Do not exhibit any prohibited characteristic of hazardous
waste identified in 40 CFR part 261, subpart C at the point of
injection.
(4) Wastes that are hazardous only because they exhibit a hazardous
characteristic, and which are otherwise prohibited under this part, are
not prohibited if the wastes meet any of the following criteria, unless
the wastes are subject to a specified method of treatment other than
DEACT in Sec. 268.40, or are D003 reactive cyanide:
(i) The wastes are managed in a treatment system which subsequently
discharges to waters of the U.S. pursuant to a permit issued under
section 402 of the Clean Water Act; or
(ii) The wastes are treated for purposes of the pretreatment
requirements of section 307 of the Clean Water Act; or
(iii) The wastes are managed in a zero discharge system engaged in
Clean Water Act-equivalent treatment as defined in Sec. 268.37(a); and
(iv) The wastes no longer exhibit a prohibited characteristic at
the point of land disposal (i.e., placement in a surface impoundment).
* * * * *
5. Section 268.2 is amended by revising paragraph (j) to read as
follows:
Sec. 268.2 Definitions applicable in this part.
* * * * *
(j) Inorganic metal-bearing waste is one for which EPA has
established treatment standards for metal hazardous constituents, and
which does not otherwise contain significant organic or cyanide content
as described in Sec. 268.3(c)(1), and is specifically listed in
appendix XI of this part.
* * * * *
6. Section 268.3 is amended by revising paragraph (b) to read as
follows:
Sec. 268.3 Dilution prohibited as a substitute for treatment.
* * * * *
[[Page 33683]]
(b) Dilution of wastes that are hazardous only because they exhibit
a characteristic in treatment systems which include land- based units
which treat wastes subsequently discharged to a water of the United
States pursuant to a permit issued under section 402 of the Clean Water
Act (CWA), or which treat wastes in a CWA-equivalent treatment system,
or which treat wastes for the purposes of pretreatment requirements
under section 307 of the CWA is not impermissible dilution for purposes
of this section unless a method other than DEACT has been specified in
Sec. 268.40 as the treatment standard, or unless the waste is a D003
reactive cyanide wastewater or nonwastewater.
* * * * *
7. Section 268.39 is amended by revising paragraph (e) to read as
follows:
Sec. 268.39 Waste specific prohibitions--spent aluminum potliners;
reactive; and carbamate wastes.
* * * * *
(e) Between July 8, 1996, and April 8, 1998, the wastes included in
paragraphs (a), (c), and (d) of this section may be disposed in a
landfill or surface impoundment, only if such unit is in compliance
with the requirements specified in Sec. 268.5(h)(2).
* * * * *
8. Section 268.40 is amended by revising the first sentence of
paragraph (a), and paragraph (e) to read as follows:
Sec. 268.40 Applicability of treatment standards.
(a) A prohibited waste identified in the table ``Treatment
Standards for Hazardous Wastes'' may be land disposed only if it meets
the requirements found in the table. * * *
* * * * *
(e) For characteristic wastes (D001-D003, and D012-D043) that are
subject to treatment standards in the following table ``Treatment
Standards for Hazardous Wastes,'' all underlying hazardous constituents
(as defined in Sec. 268.2(i)) must meet Universal Treatment Standards,
found in Sec. 268.48, ``Table UTS,'' prior to land disposal as defined
in Sec. 268.2(c) of this part.
* * * * *
Sec. 268.40 [Amended]
9. In Sec. 268.40, the table at the end of the section is amended
by removing the entries for K140, P187, P193, P195, P200, U360-U363,
U368-U371, U374, U380, U388, U397-U399, U405, U406, and U408; and by
revising the entries for D001-D003, D012-D043, F006, F007, F010, F037,
F039, K006, K008, K062, K108, K156-K161, P093, P196, P202, U277, U365,
U366, U375-U379, U381-U387, U389-U396, U400-U404, and U407; and by
adding the entries for U278, U409, U410, and U411; and by adding
footnotes 8 and 9 to read as follows:
* * * * *
Treatment Standards for Hazardous Wastes
[Note: NA means not applicable]
--------------------------------------------------------------------------------------------------------------------------------------------------------
Regulated hazardous constituent Nonwastewaters
Waste description and ----------------------------------------------------- Wastewaters (Concentration in (Concentration in mg/kg \5\
Waste code treatment/regulatory mg/l \3\, or technology code unless noted as ``mg/l
subcategory \1\ Common name CAS \2\ No. \4\) TCLP''; or technology code)
--------------------------------------------------------------------------------------------------------------------------------------------------------
D001 Ignitable Characteristic NA........................... NA DEACT and meet Sec. 268.48 DEACT and meet Sec. 268.48
Wastes, except for the standards;\8\ or RORGS;\9\ standards;\8\ or RORGS;\9\
Sec. 261.21(a)(1) High or CMBST \9\. or CMBST.\9\
TOC Subcategory.
High TOC Ignitable NA........................... NA NA........................... RORGS;\9\ or CMBST.\9\
Characteristic Liquids
Subcategory based on 40
CFR 261.21(a)(1)--
Greater than or equal
to 10% total organic
carbon. (Note: This
subcategory consists of
nonwastewaters only).
D002 Corrosive Characteristic NA........................... NA DEACT and meet Sec. 268.48 DEACT and meet Sec. 268.48
Wastes. standards \8\. standards \8\
* * * * * * *
D003 Reactive Sulfides NA........................... NA DEACT and meet Sec. 268.48 DEACT and meet Sec. 268.48
Subcategory based on standards \8\. standards.\8\
261.23(a)(5).
Explosives Subcategory NA........................... NA DEACT and meet Sec. 268.48 DEACT and meet Sec. 268.48
based on 261.23(a)(6), standards \8\. standards.\8\
(7), and (8).
Unexploded ordnance and NA........................... NA DEACT........................ DEACT
other explosive devices
which have been the
subject of an emergency
response.
Other Reactives NA........................... NA DEACT and meet Sec. 268.48 DEACT and meet Sec. 268.48
Subcategory based on standards \8\. standards.\8\
261.23(a)(1).
Water Reactive NA........................... NA NA........................... DEACT and meet Sec. 268.48
Subcategory based on standards.\8\
261.23(a)(2),(3), and
(4). (Note: This
subcategory consists of
nonwastewaters only).
Reactive Cyanides Cyanides (Total) \7\......... 57-12-5 Reserved..................... 590.\9\
Subcategory based on
261.23(a)(5).
Cyanides (Amenable)\7\....... 57-12-5 0.86\9\...................... 30.\9\
[[Page 33684]]
* * * * * * *
D012 Wastes that are TC for Endrin....................... 72-20-8 BIODG;\9\ or CMBST \9\....... 0.13 and meet Sec. 268.48
Endrin based on the standards.\8\
TCLP in SW846 Method
1311.
Endrin aldehyde.............. 7421-93-4 BIODG;\9\ or CMBST \9\....... 0.13 and meet Sec. 268.48
standards \8\
D013 Wastes that are TC for alpha-BHC.................... 319-84-6 CARBN;\9\ or CMBST \9\....... 0.066 and meet Sec. 268.48
Lindane based on the standards \8\
TCLP in SW846 Method
1311.
beta-BHC..................... 319-85-7 CARBN;\9\ or CMBST \9\....... 0.066 and meet Sec. 268.48
standards \8\
delta-BHC.................... 319-86-8 CARBN;\9\ or CMBST \9\....... 0.066 and meet Sec. 268.48
standards \8\
gamma-BHC (Lindane).......... 58-89-9 CARBN;\9\ or CMBST \9\....... 0.066 and meet Sec. 268.48
standards \8\
D014 Wastes that are TC for Methoxychlor................. 72-43-5 WETOX \9\ or CMBST \9\....... 0.18 and meet Sec. 268.48
Methoxychlor based on standards \8\
the TCLP in SW846
Method 1311.
D015 Wastes that are TC for Toxaphene.................... 8001-35-2 BIODG \9\ or CMBST \9\....... 2.6 and meet Sec. 268.48
Toxaphene based on the standards \8\
TCLP in SW846 Method
1311.
D0l6 Wastes that are TC for 2,4-D(2,4- 94-75-7 CHOXD;\9\ BIODG;\9\ or CMBST 10 and meet Sec. 268.48
2,4-D(2,4- Dichlorophenoxyacetic acid). \9\. standards \8\
Dichlorophenoxyacetic
acid) based on the TCLP
in SW846 Method 1311.
D017 Wastes that are TC for 2,4,5-TP(Silvex)............. 93-72-1 CHOXD \9\ or CMBST \9\....... 7.9 and meet Sec. 268.48
2,4,5-TP (Silvex) based standards \8\
on the TCLP in SW846
Method 1311.
D018 Wastes that are TC for Benzene...................... 71-43-2 0.14 and meet Sec. 268.48 10 and meet Sec. 268.48
Benzene based on the standards \8\. standards \8\
TCLP in SW846 Method
1311.
D019 Wastes that are TC for Carbon tetrachloride......... 56-23-5 0.057 and meet Sec. 268.48 6.0 and meet Sec. 268.48
Carbon tetrachloride standards \8\. standards \8\
based on the TCLP in
SW846 Method 1311.
D020 Wastes that are TC for Chlordane (alpha and gamma 57-74-9 0.0033 and meet Sec. 268.48 0.26 and meet Sec. 268.48
Chlordane based on the isomers). standards \8\. standards \8\
TCLP in SW846 Method
1311.
D021 Wastes that are TC for Chlorobenzene................ 108-90-7 0.057 and meet Sec. 268.48 6.0 and meet Sec. 268.48
Chlorobenzene based on standards8. standards.8
the TCLP in SW846
Method 1311.
D022 Wastes that are TC for Chloroform................... 67-66-3 0.046 and meet Sec. 268.48 6.0 and meet Sec. 268.48
Chloroform based on the standards8. standards.8
TCLP in SW846 Method
1311.
D023 Wastes that are TC for o- o-Cresol..................... 95-48-7 0.11 and meet Sec. 268.48 5.6 and meet Sec. 268.48
Cresol based on the standards8. standards.8
TCLP in SW846 Method
1311.
D024 Wastes that are TC for m- M-Cresol (difficult to 108-39-4 0.77 and meet Sec. 268.48 5.6 and meet Sec. 268.48
Cresol based on the distinguish from p-cresol). standards8. standards.8
TCLP in SW846 Method
1311.
D025 Wastes that are TC for p- p-Cresol (difficult to 106-44-5 0.77 and meet Sec. 268.48 5.6 and meet Sec. 268.48
Cresol based on the distinguish from m-cresol). standards8. standards.8
TCLP in SW846 Method
1311.
D026 Wastes that are TC for Cresol-mixed isomers 1319-77-3 0.88 and meet Sec. 268.48 11.2 and meet Sec. 268.48
Cresols (Total) based (Cresylic acid) (sum of o-, standards8. standards.8
on the TCLP in SW846 m-, and p-cresol
Method 1311. concentrations).
D027 Wastes that are TC for p- p-Dichlorobenzene (1,4- 106-46-7 0.090 and meet Sec. 268.48 6.0 and meet Sec. 268.48
Dichloro- benzene based Dichloro- benzene). standards8. standards.8
on the TCLP in SW846
Method 1311.
D028 Wastes that are TC for 1,2-Dichloroethane........... 107-06-2 0.21 and meet Sec. 268.48 6.0 and meet Sec. 268.48
1,2-Dichloroethane standard8. standards.8
based on the TCLP in
SW846 Method 1311.
[[Page 33685]]
D029 Wastes that are TC for 1,1-Dichlorethylene.......... 75-35-4 0.025 and meet Sec. 268.48 6.0 and meet Sec. 268.48
1,1-Dichloroethylene standards8. standards.8
based on the TCLP in
SW846 Method 1311.
D030 Wastes that are TC for 2,4-Dinitrotoluene........... 121-14-2 0.32 and meet Sec. 268.48 140 and meet Sec. 268.48
2,4-Dinitrotoluene standards8. standards.8
based on the TCLP in
SW846 Method 1311.
D031 Wastes that are TC for Heptachlor................... 76-44-8 0.0012 and meet Sec. 268.48 0.066 and meet Sec. 268.48
Heptachlor based on the standards8. standards.8
TCLP in SW846 Method
1311.
Heptachlor epoxide........... 1024-57-3 0.016 and meet Sec. 268.48 0.066 and meet Sec. 268.48
standards8. standards.8
D032 Wastes that are TC for Hexachlorobenzene............ 118-74-1 0.055 and meet Sec. 268.48 10 and meet Sec. 268.48
Hexachloro- benzene standards8. standards.8
based on the TCLP in
SW846 Method 1311.
D033 Wastes that are TC for Hexa- chlorobutadiene........ 87-68-3 0.055 and meet Sec. 268.48 5.6 and meet Sec. 268.48
Hexachlorobutadiene standards8. standards.8
based on the TCLP in
SW846 Method 1311.
D034 Wastes that are TC for Hexachloroethane............. 67-72-1 0.055 and meet Sec. 268.48 30 and meet Sec. 268.48
Hexachloroethane based standards8. standards.8
on the TCLP in SW846
Method 1311.
D035 Wastes that are TC for Methyl ethyl ketone.......... 78-93-3 0.28 and meet Sec. 268.48 36 and meet Sec. 268.48
Methyl ethyl ketone standard8. standards.8
based on the TCLP in
SW846 Method 1311.
D036 Wastes that are TC for Nitrobenzene................. 98-95-3 0.068 and meet Sec. 268.48 14 and meet Sec. 268.48
Nitrobenzene based on standards8. standards.8
the TCLP in SW846
Method 1311.
D037 Wastes that are TC for Pentachlorophenol............ 87-86-5 0.089 and meet Sec. 268.48 7.4 and meet Sec. 268.48
Pentachlorophenol based standards8. standards.8
on the TCLP in SW846
Method 1311.
D038 Wastes that are TC for Pyridine..................... 110-86-1 0.014 and meet Sec. 268.48 16 and meet Sec. 268.48
Pyridine based on the standards8. standards.8
TCLP in SW846 Method
1311.
D039 Wastes that are TC for Tetracholorethylene.......... 127-18-4 0.056 and meet Sec. 268.48 6.0 and meet Sec. 268.48
Tetrachloroethylene standards.. standards.8
based on the TCLP in
SW846 Method 1311.
D040 Wastes that are TC for Trichloroethylene............ 79-01-6 0.054 and meet Sec. 268.48 6.0 and meet Sec. 268.48
Trichloroethylene based standards8. standards.8
on the TCLP in SW846
Method 1311.
D041 Wastes that are TC for 2,4,5-Trichlorophenol........ 95-95-4 0.18 and meet Sec. 268.48 7.4 and meet Sec. 268.48
2,4,5-Trichlorophenol standards8. standards.8
based on the TCLP in
SW846 Method 1311.
D042 Wastes that are TC for 2,4,6-Tricholorphenol........ 88-06-2 0.035 and meet Sec. 268.48 7.4 and meet Sec. 268.48
2,4,6-Trichlorophenol standards8. standards.8
based on the TCLP in
SW846 Method 1311.
D043 Wastes that are TC for Vinyl chloride............... 75-01-4 0.27 and meet Sec. 268.48 6.0 and meet Sec. 268.48
Vinyl chloride based on standards8. standards.8
the TCLP in SW846
Method 1311.
* * * * * * *
F006 Wastewater treatment Cadmium...................... 7440-43-9 .069......................... 0.19 mg/l TCLP.
sludges from
electroplating
operations except from
the following
processes: (1) Sulfuric
acid anodizing of
aluminum; (2) tin
plating on carbon
steel; (3) zinc plating
(segregated basis) on
carbon steel; (4)
aluminum or zinc-
aluminum plating on
carbon steel; (5)
cleaning/stripping
associated with tin,
zinc and aluminum
plating on carton
steel; and (6) chemical
etching and milling of
aluminum.
* * * * *
Silver....................... 7440-22-4 NA........................... 0.30 mg/l TCLP.
F007 Spent cyanide plating Cadmium...................... 7440-43-9 NA........................... 0.19 mg/l TCLP.
bath solutions from
electroplating
operations.
* * * * *
[[Page 33686]]
* * * * * * *
F010 Quenching bath residues Cyanides (Total) \7\......... 57-12-5 1.2.......................... 590.
from oil baths from
metal heat treating
operations where
cyanides are used in
the process.
Cyanides (Amenable) \7\...... 57-12-5 0.86......................... NA.
* * * * * * *
F037 Petroleum refinery Acenaphthene................. 83-32-9 0.059........................ 3.4.
primary oil/water/
solids separation
sludge--Any sludge
generated from the
gravitational
separation of oil/water/
solids during the
storage or treatment of
process wastewaters and
oily cooling
wastewaters from
petroleum refineries.
Such sludges include,
but are not limited to,
those generated in: oil/
water/solids
separators; tanks and
impoundments; ditches
and other conveyances;
sumps; and stormwater
units receiving dry
weather flow. Sludge
generated in stormwater
units that do not
receive dry weather
flow, sludges generated
from non-contact once-
through cooling waters
segregated for
treatment from other
process or oily cooling
waters, sludges
generated in aggressive
biological treatment
units as defined in
Sec. 261.31(b)(2)
(including sludges
generated in one or
more additional units
after wastewaters have
been treated in
aggressive biological
treatment units) and
KO51 wastes are not
included in this
listing.
* * * * *
Nickel....................... 7440-02-0 NA........................... 5.0 mg/l TCLP.
* * * * * * *
F039 Leachate (liquids that Acenaphthylene............... 208-96-8 0.059........................ NA.
have percolated through
land disposed wastes)
resulting from the
disposal of more than
one restricted waste
classified as hazardous
under subpart D of this
part. (Leachate
resulting from the
disposal of one or more
of the following EPA
Hazardous Wastes and no
other Hazardous Wastes
retains its EPA
Hazardous Waste
Number(s): F020, F021,
F022, F026, F027, and/
or F028.).
* * * * *
Acetonitrile................. 75-05-8 5.6.......................... NA.
* * * * *
Carbon disulfide............. 75-15-0 3.8.......................... NA.
* * * * *
2-Chloro-1,3-butadiene....... 126-99-8 0.057........................ NA.
* * * * *
Cyclohexanone................ 108-94-1 0.36......................... NA
* * * * *
1,4-Dioxane.................. 123-91-1 12.0......................... 170.
Diphenylamine (difficult to 122-39-4 0.92......................... NA.
distinguish from
diphenylnitrosamine).
Diphenylnitrosamine 86-30-6 0.92......................... NA.
(difficult to distinguish
from diphenylamine).
1,2-Diphenylhydrazine........ 122-66-7 0.087........................ NA.
* * * * *
Methanol..................... 67-56-1 5.6.......................... NA.
* * * * *
[[Page 33687]]
N-Nitrosodimethylamine....... 62-75-9 0.40......................... NA.
* * * * *
Phthalic anhydride........... 85-44-9 0.055........................ NA.
* * * * *
tris(2,3-Dibromopropyl) 126-72-7 0.11......................... NA.
phosphate.
* *................... * * *
Beryllium.................... 7440-41-7 0.82......................... NA.
* *................... * * *
Cyanides (Amenable).......... 57-12-5 0.86......................... NA.
Fluoride..................... 16964-48-8 35........................... NA.
* *................... * * *
Thallium..................... 7440-28-0 1.4.......................... NA.
Vanadium..................... 7440-62-2 4.3.......................... NA.
* * * * * * *
K006 Wastewater treatement Chromium (Total)............. 7440-47-3 2.77......................... 0.86 mg/l TCLP.
sludge from the
production of chrome
oxide green pigments
(anhydrous).
Lead......................... 7439-92-1 0.69......................... 0.37 mg/l TCLP.
Wastewater treatment Chromium (Total)............. 7440-47-3 2.77......................... 0.86 mg/l TCLP.
sludge from the
production of chrome
oxide green pigments
(hydrated).
Lead......................... 7439-92-1 0.69......................... 0.37 mg/l TCLP.
* * * * * * *
K008 Oven residue from the Chromium (Total)............. 7440-47-3 2.77......................... 0.86 mg/l TCLP.
production of chrome
oxide green pigments.
Lead......................... 7439-92-1 0.69......................... 0.37 mg/l TCLP.
* * * * * * *
K062 Spent pickle liquor Chromium (Total)............. 7440-47-3 2.77......................... 0.86 mg/l TCLP.
generated by steel
finishing operations of
facilities within the
iron and steel industry
(SIC Codes 331 and 332).
Lead......................... 7439-92-1 0.69......................... 0.37 mg/l TCLP.
Nickel....................... 7440-02-0 3.98......................... 5.0 mg/l TCLP.
* * * * * * *
K108 Condensed column NA........................... NA CMBST; or CHOXD fb CARBN; or CMBST.
overheads from product BIODG fb CARBN.
separation and
condensed reactor vent
gases from the
production of 1,1-
dimethylhydrazide
(UDMH) from carboxylic
acid hydrazides.
* * * * * * *
K156 Organic waste (including Acetonitrile................. 75-05-8 5.6.......................... 1.8.
heavy ends, still
bottoms, light ends,
spent solvents,
filtrates, and
decantates) from the
production of
carbamates and
carbamoyl oximes.
Acetophenone................. 96-86-2 0.010........................ 9.7.
Aniline...................... 62-53-3 0.81......................... 14.
Benomyl...................... 17804-35-2 0.056........................ 1.4.
Benzene...................... 71-43-2 0.14......................... 10.
Carbaryl..................... 63-25-2 0.006........................ 0.14.
Carbenzadim.................. 10605-21-7 0.056........................ 1.4.
Carbofuran................... 1563-66-2 0.006........................ 0.14.
Carbosulfan.................. 55285-14-8 0.028........................ 1.4.
Chlorobenzene................ 108-90-7 0.057........................ 6.0.
Chloroform................... 67-66-3 0.046........................ 6.0.
o-Dichlorobenzene............ 95-50-1 0.088........................ 6.0.
Methomyl..................... 16752-77-5 0.028........................ 0.14.
Methylene chloride........... 75-09-2 0.089........................ 30.
Methyl ethyl ketone.......... 78-93-3 0.28......................... 36.
Naphthalene.................. 91-20-3 0.059........................ 5.6.
Phenol....................... 108-95-2 0.039........................ 6.2.
[[Page 33688]]
Pyridine..................... 110-86-1 0.014........................ 16.
Toluene...................... 108-88-3 0.080........................ 10.
Triethylamine................ 121-44-8 0.081........................ 1.5.
K157 Wastewaters (including Carbon tetrachloride......... 56-23-5 0.057........................ 6.0.
scrubber waters,
condenser waters,
washwaters, and
separation waters) from
the production of
carbamates and
carbamoyl oximes.
Chloroform................... 67-66-3 0.046........................ 6.0.
Chloromethane................ 74-87-3 0.19......................... 30.
Methomyl..................... 16752-77-5 0.028........................ 0.14.
Methylene chloride........... 75-09-2 0.089........................ 30.
Methyl ethyl ketone.......... 78-93-3 0.28......................... 36.
o-Phenylenediamine........... 95-54-5 0.056........................ 5.6.
Pyridine..................... 110-86-1 0.014........................ 16.
Triethylamine................ 121-44-8 0.081........................ 1.5.
K158 Bag house dusts and Benomyl...................... 17804-35-2 0.056........................ 1.4.
filter/separation
solids from the
production of
carbamates and
carbamoyl oximes.
Benzene...................... 71-43-2 0.14......................... 10.
Carbenzadim.................. 10605-21-7 0.056........................ 1.4.
Carbofuran................... 1563-66-2 0.006........................ 0.14.
Carbosulfan.................. 55285-14-8 0.028........................ 1.4.
Chloroform................... 67-66-3 0.046........................ 6.0.
Methylene chloride........... 75-09-2 0.089........................ 30.
Phenol....................... 108-95-2 0.039........................ 6.2.
K159 Organics from the Benzene...................... 71-43-2 0.14......................... 10.
treatment of
thiocarbamate wastes.
Butylate..................... 2008-41-5 0.042........................ 1.4.
EPTC (Eptam)................. 759-94-4 0.042........................ 1.4.
Molinate..................... 2212-67-1 0.042........................ 1.4.
Pebulate..................... 1114-71-2 0.042........................ 1.4.
Vernolate.................... 1929-77-7 0.042........................ 1.4.
K160 Solids (including filter Butylate..................... 2008-41-5 0.042........................ 1.4.
wastes, separation
solids, and spent
catalysts) from the
production of
thiocarabamates and
solids from the
treatment of
thiocarbamate wastes.
EPTC (Eptam)................. 759-94-4 0.042........................ 1.4.
Molinate..................... 2212-67-1 0.042........................ 1.4.
Pebulate..................... 1114-71-2 0.042........................ 1.4.
Toluene...................... 108-88-3 0.080........................ 10.
Vernolate.................... 1929-77-7 0.042........................ 1.4.
K161 Purifcation solids Antimony..................... 7440-36-0 1.9.......................... 2.1mg/l TCLP.
(including filtration,
evaporation, and
centrifugation solids),
baghouse dust and floor
sweepings, from the
production of
dithiocarbarmate acids
and their salts.
Arsenic...................... 7440-38-2 1.4.......................... 5.0 mg/l TCLP.
Carbon disulfide............. 75-15-0 3.8.......................... 4.8 mg/l TCLP.
Dithiocarbamates (total)..... NA 0.028....................... 28.
Lead......................... 7439-92-1 0.069........................ 0.37 mg/l TCLP.
Nickel....................... 7440-02-0 3.98......................... 5.0 mg/l TCLP.
Selenium..................... 7782-49-2 0.82......................... 0.16 mg/l TCLP.
* * * * * * *
P093 Phenylthiourea.......... Phenylthiourea............... 103-85-5 (WETOX or CHOXD) fb CARBN; or CMBST.
CMBST.
* * * * * * *
P196 Manganese Dithiocarbamates (total)..... NA 0.028........................ 28.
dimethyldithiocarbamate.
* * * * * * *
P202 M-Cumenyl m-Cumenyl methycarbamate..... 64-00-6 0.056........................ 1.4.
methylcarbamate.
[[Page 33689]]
* * * * * * *
P205 Ziram................... Dithiocarbamates (total)..... NA 0.028........................ 28.
* * * * * * *
U277 Sulfallate.............. Dithiocarbamates (total)..... NA 0.028........................ 28.
U278 Bendiocarb.............. Bendiocarb................... 22781-23-3 0.056........................ 1.4.
* * * * * * *
U365 Molinate................ Molinate..................... 2212-67-1 0.042........................ 1.4.
U366 Dazomet................. Dithiocarbamates (total)..... NA 0.028........................ 28.
* * * * * * *
U375 3-lodo-2-propynyl n- 3-lodo-2-propynyl n- 55406-53-6 0.056........................ 1.4.
butylcarbamate. butylcarbamate.
U376 Selenium, tetrakis Dithiocarbamates (total)..... NA 0.028........................ 28.
(dimethyldithio-
carbamate).
Selenium................ Selenium..................... 7782-49-2 0.82......................... 0.16 mg/l TCLP.
U377 Pottasium n- Dithiocarbamates (total)..... NA 0.028........................ 28.
methyldithiocarbamate.
U378 Potassium n- Dithiocarbamates (total)..... NA 0.028........................ 28.
hydroxymethyl-n-
methyldithiocarbamate.
U379 Sodium Dithiocarbamates (total)..... NA 0.028........................ 28.
dibutyldithiocarbamate.
U381 Sodium Dithiocarbamates (total)..... NA 0.028........................ 28.
diethyldithiocarbamate.
U382 Sodium Dithiocarbamates (total)..... NA 0.028........................ 28.
dimethyldithiocarbamate.
U383 Potassium dimethyl Dithiocarbamates (total)..... NA 0.028........................ 28.
dithiocarbamate.
U384 Metam Sodium............ Dithiocarbamates (total)..... NA 0.028........................ 28.
U385 Vernolate............... Vernolate.................... 1929-77-7 0.042........................ 1.4.
U386 Cycloate................ Cycloate..................... 1134-23-2 0.042........................ 1.4.
U387 Prosulfocarb............ Prosulfocarb................. 52888-80-9 0.042........................ 1.4.
U389 Triallate............... Triallate.................... 2303-17-5 0.042........................ 1.4.
U390 EPTC.................... EPTC......................... 759-94-4 0.042........................ 1.4.
U391 Pebulate................ Pebulate..................... 1114-71-2 0.042........................ 1.4.
U392 Butylate................ Butylate..................... 2008-41-5 0.042........................ 1.4.
U393 Copper Dithiocarbamates (total)..... NA 0.028........................ 28.
dimethyldithiocarbamate.
U394 A2213................... A2213........................ 30558-43-1 0.042........................ 1.4.
U395 Diethylene glycol, Diethylene glycol, 5952-26-1 0.056........................ 1.4.
dicarbamate. dicarbamate.
U396 Ferbam.................. Dithiocarbamates (total)..... NA 0.028........................ 28.
U400 Bis (pentamethylene) Dithiocarbamates (total)..... NA 0.028........................ 28.
thiuram tetrasulfide.
U401 Tetramethyl thiuram Dithiocarbamates (total)..... NA 0.028........................ 28.
monosulfide.
U402 Tetrabutylthiuram Dithiocarbamates (total)..... NA 0.028........................ 28.
disulfide.
U403 Disulfiram.............. Dithiocarbamates (total)..... NA 0.028........................ 28.
U404 Triethylamine........... Triethylamine................ 101-44-8 0.081........................ 1.5.
U407 Ethyl Ziram............. Dithiocarbamates (total)..... NA 0.028........................ 28.
U409 Thiophanate-methyl...... Thiophanate-methyl........... 23564-05-8 0.056........................ 1.4.
U410 Thiodicarb.............. Thiodicarb................... 59669-26-0 0.019........................ 1.4.
U411 Propoxur................ Propoxur..................... 114-26-1 0.056........................ 1.4.
--------------------------------------------------------------------------------------------------------------------------------------------------------
\1\ The waste descriptions provided in this table do not replace waste descriptions in 40 CFR 261. Descriptions of Treatment/Regulatory Subcategories
are provided, as needed, to distinguish between applicability of different standards.
[[Page 33690]]
\2\ CAS means Chemical Abstract Services. When the waste code and/or regulated constituents are described as a combination of a chemical with it's salts
and/or esters, the CAS number is given for the parent compound only.
\3\ Concentration standards for wastewaters are expressed in mg/l and are based on analysis of composite samples.
\4\ All treatment standards expressed as a Technology Code or combination of Technology Codes are explained in detail in 40 CFR 268.42 Table 1--
Technology Codes and Descriptions of Technology-Based Standards.
\5\ Except for Metals (EP or TCLP) and Cyanides (Total and Amenable) the nonwastewater treatment standards expressed as a concentration were
established, in part, based upon incineration in units operated in accordance with the technical requirements of 40 CFR Part 264 Subpart O or Part 265
Subpart O, or based upon combustion in fuel substitution units operating in accordance with applicable technical requirements. A facility may comply
with these treatment standards according to provisions in 40 CFR 268.40(d). All concentration standards for nonwastewaters are based on analysis of
grab samples.
* * * * * * *
\7\ Both Cyanides (Total) and Cyanides (Amenable) for nonwastewaters are to be analyzed using Method 9010 or 9012, found in ``Test Methods for
Evaluating Solid Waste, Physical/Chemical Methods'', EPA Publication SW-846, as incorporated by reference in 40 CFR 260.11, with a sample size of 10
grams and a distillation time of one hour and 15 minutes.
\8\ These wastes, when rendered nonhazardous and then subsequently managed in CWA, CWA-equivalent, or Class I SDWA systems are not subject to treatment
standards. (See Sec. 148.1(d) and Sec. 268.1(c) (3) and (4)).
\9\ These wastes, when rendered nonhazardous and then subsequently injected in a Class I SDWA well are not subject to treatment standards. (See Sec.
148.1(d)).
10. In subpart D, Sec. 268.48 the table in paragraph (a) is revised
to read as follows:
Sec. 268.48 Universal treatment standards.
(a) * * *
Universal Treatment Standards
[Note: NA means not applicable.]
----------------------------------------------------------------------------------------------------------------
Nonwastewater
Wastewater standard Pstandard
Regulated constituent/common name CAS \1\ No. (Concentration in mg/ (Concentration in mg/
l \2\) kg \3\ unless noted
as ``mg/l TCLP'')
----------------------------------------------------------------------------------------------------------------
* * * * * *
*
A2213............................................. 30558-43-1 0.042 1.4
* * * * * *
*
Butylate.......................................... 2008-41-5 0.042 1.4
* * * * * *
*
Cycloate.......................................... 1134-23-2 0.042 1.4
* * * * * *
*
EPTC.............................................. 759-94-4 0.042 1.4
* * * * * *
*
Molinate.......................................... 2212-67-1 0.042 1.4
* * * * * *
*
Pebulate.......................................... 1114-71-2 0.042 1.4
* * * * * *
*
Prosulfocarb...................................... 52888-80-9 0.042 1.4
* * * * * *
*
Triallate......................................... 2303-17-5 0.042 1.4
* * * * * *
*
Vernolate......................................... 1929-77-7 0.042 1.4
* * * * * *
*
----------------------------------------------------------------------------------------------------------------
\1\ CAS means Chemical Abstract Services. When the waste code and/or regulated constituents are described as a
combination of a chemical with it's salts and/or esters, the CAS number is given for the parent compound only.
\2\ Concentration standards for wastewaters are expressed in mg/l and are based on analysis of composite
samples.
\3\ Except for Metals (EP or TCLP) and Cyanides (Total and Amenable) the nonwastewater treatment standards
expressed as a concentration were established, in part, based upon incineration in units operated in
accordance with the technical requirements of 40 CFR part 264, subpart O or 40 CFR part 265, subpart O, or
based upon combustion in fuel substitution units operating in accordance with applicable technical
requirements. A facility may comply with these treatment standards according to provisions in 40 CFR
268.40(d). All concentration standards for nonwastewaters are based on analysis of grab samples.
[[Page 33691]]
* * * * *
[FR Doc. 96-16540 Filed 6-27-96; 8:45 am]
BILLING CODE 6560-50-P