2013-07107. Defense Federal Acquisition Regulation Supplement; Specialty Metals-Definition of “Produce” (DFARS Case 2012-D041)  

  • Start Preamble

    AGENCY:

    Defense Acquisition Regulations System, Department of Defense (DoD).

    ACTION:

    Final rule.

    SUMMARY:

    DoD is issuing a final rule amending the Defense Federal Acquisition Regulation Supplement (DFARS) to revise the definition of “produce” as it applies to specialty metals. The National Defense Authorization Act for Fiscal Year 2011 directed DoD to review the definition of “produce” to ensure its compliance with the statutory restrictions on specialty metals and to determine if a revision to the current rule was necessary and appropriate.

    DATES:

    Effective Date: March 28, 2013.

    Start Further Info

    FOR FURTHER INFORMATION CONTACT:

    Ms. Amy Williams, Telephone 571-372-6106.

    End Further Info End Preamble Start Supplemental Information

    SUPPLEMENTARY INFORMATION:

    I. Background

    DoD published a proposed rule in the Federal Register at 77 FR 43474 on July 24, 2012. DoD proposed to amend the definition of “produce” to eliminate the phrase “quenching and tempering” of armor steel plate, and to expand the application of the other listed technologies, currently restricted just to titanium and titanium alloys, to any specialty metal that could be formed by such technologies.

    DoD received comments on the proposed rule from 13 respondents.

    II. Discussion and Analysis

    DoD reviewed the public comments in the development of the final rule. A discussion of the comments and the changes made to the rule as a result of those comments is provided, as follows:

    A. Summary of Significant Changes

    The phrase “gas atomization” in the definition of “produce” has been revised to read “atomization,” in order to allow for other types of atomization (e.g., gas, water, centrifugal, plasma).Start Printed Page 18878

    B. Analysis of Comments

    1. Definition of “Produce”

    Comment: All respondents strongly supported the proposed definition of “produce.” Some of the benefits of the revised definition noted by the respondents are as follows:

    Provides domestic control of material vital to protection of our troops is critical to national security interests, promotes self-sufficiency of U.S. defense industry.

    Helps maintain a strong domestic armor steel plate industry and strengthens our defense industrial base, as well as the overall economic strength of the United States. Incentivizes investment in the manufacturing capacity, process technology, research and development necessary to meet the needs of the U.S. military, thereby reducing the possibility of supply shortages. Adds new U.S. steelmaking jobs, as well as jobs throughout the steelmaking supply chain.

    Is consistent with statutory language and legislative history.

    Response: Noted.

    2. Impact of Changes in Production Capacity of Domestic Producers of Steel Plate

    Comment: Some respondents commented on the statement by DoD in the Federal Register preamble to the proposed rule, that there is now sufficient capacity to meet DoD requirements, if DoD were to remove “quenching and tempering of steel plate” from the definition of “produce.” One respondent expressed concern that by linking the regulatory definition of “produce” to changes in capacity, DoD is creating uncertainty and discourages potential investors from building or maintaining domestic production.

    Several respondents also commented that there are already existing statutory authorities (i.e., the nonavailability and national security exceptions), which should provide sufficient flexibility and make it unnecessary to revisit the issue of the definition of “produce.”

    Response: Since these respondents are all strongly in support of the proposed rule, no change is necessary in the final rule.

    3. Other Processes

    Comment: One respondent expressed support for DoD's decision to amend the definition of “produce” to create a uniform definition for all specialty metals. Several respondents noted that the definition now only includes those technologies that make a significant contribution equivalent to melting, and allows for flexibility and future technology advances that could replace the melt stage for certain specialty metals.

    Response: Noted.

    Comment: One respondent stated that atomization of metal is not always achieved by using a stream of gas. Atomization may also be achieved by rotating molten metal at high speeds. Therefore, the respondent recommended deletion of the word “gas” from the proposed definition of “produce.”

    Response: DoD has removed the word “gas” from the final rule.

    Comment: The same respondent stated that the final consolidation of metal powders produced through atomization would not be sufficient to confer domestic origin on the resulting article, because the atomization process uses molten metal. Therefore, the metal powder produced through atomization is a melt-derived powder, rather than a non-melt derived powder. The respondent did not request a change to the rule with regard to this issue, but requested clarification in the preamble to the final rule that articles produced from melt-derived metal powders, including metal powders produced through atomization, would have to be consolidated from domestically melted metal powders in order to be considered products of the United States.

    Response: DoD has created a vertical list to improve the clarity with regard to the three processes that constitute production, and must therefore be performed in the United States: (i) Atomization; (ii); sputtering; or (iii) final consolidation of non-melt derived powders.

    It is very clear that final consolidation only constitutes production with regard to metal powders that are derived by non-melt processes (such as mechanical or chemical processes). It is acceptable for non-melt processes to occur outside the United States, as long as final consolidation occurs in the United States, but any processes involving melting must occur in the United States.

    III. Executive Orders 12866 and 13563

    Executive Orders (E.O.s) 12866 and 13563 direct agencies to assess all costs and benefits of available regulatory alternatives and, if regulation is necessary, to select regulatory approaches that maximize net benefits (including potential economic, environmental, public health and safety effects, distributive impacts, and equity). E.O. 13563 emphasizes the importance of quantifying both costs and benefits, of reducing costs, of harmonizing rules, and of promoting flexibility. This is not a significant regulatory action and, therefore, was not subject to review under section 6(b) of E.O. 12866, Regulatory Planning and Review, dated September 30, 1993. This rule is not a major rule under 5 U.S.C. 804.

    IV. Regulatory Flexibility Act

    A final regulatory flexibility analysis has been prepared consistent with the Regulatory Flexibility Act, 5 U.S.C. 601, et seq., and is summarized as follows:

    DoD has issued a final rule amending the Defense Federal Acquisition Regulation Supplement (DFARS) to revise the definition of “produce” as it applies to specialty metals. The National Defense Authorization Act for Fiscal Year 2011 directed DoD to review the definition of “produce” to ensure its compliance with 10 U.S.C. 2533b and to determine if a revision to the current rule was necessary and appropriate.

    The objective of the proposed rule is to revise the definition of “produce” as it applies to production of specialty metals, in response to comments received and consideration of current technologies for production of specialty metals other than titanium. The legal basis for the rule is 10 U.S.C. 2533b. No significant issues were raised by the public comments in response to the initial regulatory flexibility analysis. There were no comments filed by the Chief Counsel for Advocacy of the Small Business Administration.

    The final rule affects primarily producers of specialty metal steel armor plate, and manufacturers that supply steel armor plate that will be incorporated into end items to be acquired by DoD. Producers of specialty metals are generally large businesses. There is a high capitalization requirement to establish a business that can melt or produce specialty metals. The small business size standard for primary metal manufacturing ranges from 500 to 1,000 employees. All the specialty metals producers reviewed had more than 500 employees. There are numerous manufacturers of products containing specialty metals, either as prime contractors or subcontractors. DoD does not have the data to determine the total number of these manufacturers, or the number that are small businesses, because the Federal Procurement Data System only collects data on prime contractors and end items, not subcontractors and components of end items.

    There are no projected reporting, recordkeeping, or other compliance requirements.

    DoD did not identify any significant alternatives to the rule which would minimize any impact of the rule on Start Printed Page 18879small entities and still meet the requirements of the statute 10 U.S.C. 2533b.

    V. Paperwork Reduction Act

    The rule does not contain any information collection requirements that require the approval of the Office of Management and Budget under the Paperwork Reduction Act (44 U.S.C. chapter 35).

    Start List of Subjects

    List of Subjects in 48 CFR Part 252

    • Government procurement
    End List of Subjects Start Signature

    Kortnee Stewart,

    Editor, Defense Acquisition Regulations System.

    End Signature

    Therefore, DoD amends 48 CFR part 252 as follows:

    Start Part

    PART 252—SOLICITATION PROVISIONS AND CONTRACT CLAUSES

    End Part Start Amendment Part

    1. The authority citation for part 252 continues to read as follows:

    End Amendment Part Start Authority

    Authority: 41 U.S.C. 1303 and 48 CFR Chapter 1.

    End Authority
    [Amended]
    Start Amendment Part

    2. Section 252.212-7001 is amended by—

    End Amendment Part Start Amendment Part

    a. Removing clause date “(FEB 2013)” and adding “(MAR 2013)” in its place; and

    End Amendment Part Start Amendment Part

    b. In paragraph (b)(7), by removing the clause date “(JUL 2009)” and adding “(MAR 2013)” in its place; and

    End Amendment Part Start Amendment Part

    c. In paragraph (b)(8), by removing the clause date “(JUN 2012)” and adding “(MAR 2013)” in its place.

    End Amendment Part Start Amendment Part

    3. Section 252.225-7008 is amended by—

    End Amendment Part Start Amendment Part

    a. Removing clause date “(JUL 2009)” and adding “(MAR 2013)” in its place; and

    End Amendment Part Start Amendment Part

    b. Removing the numerical designations preceding the definition headings of “Alloy”; “Produce”; “Specialty metal”; and “Steel”.

    End Amendment Part Start Amendment Part

    c. Revising the definition of “Produce” in paragraph (a) to read as follows:

    End Amendment Part
    Restriction on Acquisition of Specialty Metals.
    * * * * *

    (a) * * *

    Produce means—

    (i) Atomization;

    (ii) Sputtering; or

    (iii) Final consolidation of non-melt derived metal powders.

    * * * * *
    Start Amendment Part

    4. Section 252.225-7009 is amended by—

    End Amendment Part Start Amendment Part

    a. Removing clause date “(JUN 2012)” and adding “(MAR 2013)” in its place; and

    End Amendment Part Start Amendment Part

    b. Removing the numerical designations preceding the definition headings of “Alloy”; “Assembly”; “Commercial derivative military article”; “Commercially available off-the-shelf item”; “Component”; “Electronic component”; “End item”; “High performance magnet”; “Produce”; “Qualifying country”; “Required form”; “Specialty metal”; “Steel”; and “Subsystem”.

    End Amendment Part Start Amendment Part

    c. Revising the definition of “Produce” in paragraph (a) to read as follows:

    End Amendment Part
    Restriction on Acquisition of Certain Articles Containing Specialty Metals.
    * * * * *

    (a) * * *

    Produce means—

    (i) Atomization;

    (ii) Sputtering; or

    (iii) Final consolidation of non-melt derived metal powders.

    * * * * *
    [Amended]
    Start Amendment Part

    5. Section 252.244-7000 is amended by—

    End Amendment Part Start Amendment Part

    a. Removing clause date “(JUN 2012)” and adding “(MAR 2013)” in its place; and

    End Amendment Part Start Amendment Part

    b. In paragraph (b), by removing the clause date “(JUN 2012)” and adding “(MAR 2013)” in its place.

    End Amendment Part End Supplemental Information

    [FR Doc. 2013-07107 Filed 3-27-13; 8:45 am]

    BILLING CODE 5001-06-P

Document Information

Comments Received:
0 Comments
Published:
03/28/2013
Department:
Defense Acquisition Regulations System
Entry Type:
Rule
Action:
Final rule.
Document Number:
2013-07107
Pages:
18877-18879 (3 pages)
RINs:
0750-AH78
Topics:
Government procurement
PDF File:
2013-07107.pdf
CFR: (4)
48 CFR 252.212-7001
48 CFR 252.225-7008
48 CFR 252.225-7009
48 CFR 252.244-7000