94-1049. Tamper-Evident Packaging Requirements for Over-The-Counter Human Drug Products  

  • [Federal Register Volume 59, Number 11 (Tuesday, January 18, 1994)]
    [Unknown Section]
    [Page 0]
    From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
    [FR Doc No: 94-1049]
    
    
    [[Page Unknown]]
    
    [Federal Register: January 18, 1994]
    
    
    =======================================================================
    -----------------------------------------------------------------------
    
    DEPARTMENT OF HEALTH AND HUMAN SERVICES
    
    Food and Drug Administration
    
    21 CFR Part 211
    
    [Docket No. 92N-0314]
    
     
    
    Tamper-Evident Packaging Requirements for Over-The-Counter Human 
    Drug Products
    
    AGENCY: Food and Drug Administration, HHS.
    
    ACTION: Proposed rule.
    
    -----------------------------------------------------------------------
    
    SUMMARY: The Food and Drug Administration (FDA) is proposing to amend 
    its tamper-resistant packaging requirements to require that all over-
    the-counter (OTC) human drug products marketed in two-piece, hard 
    gelatin capsules be sealed. This proposal follows continuing tampering 
    incidents involving two-piece, hard gelatin capsules. The agency is 
    also proposing a change in terminology throughout its regulatory 
    program from ``tamper-resistant`` to ``tamper-evident.`` In addition, 
    FDA is soliciting comments on whether additional regulatory changes, 
    such as packaging performance standards, may be necessary. These 
    proposed amendments are part of the agency's continuing review of the 
    potential public health threat posed by product tampering and are meant 
    to address specific vulnerabilities in the OTC drug market and to 
    improve consumer protection.
    
    DATES: Written comments by March 21, 1994. FDA proposes that any final 
    rule that may issue based on this proposal have an initial effective 
    date of 1 year after its date of publication in the Federal Register. 
    All OTC drug products marketed in two-piece, hard gelatin capsules that 
    are initially introduced or initially delivered for introduction into 
    interstate commerce on or after this date must be sealed according to 
    the requirements of the final rule. In addition, FDA proposes a retail 
    level effective date of 2 years after the date of publication of a 
    final rule in the Federal Register. All two-piece, hard gelatin 
    capsules subject to the final rule, including products held for sale at 
    the retail level, must be sealed in compliance with these requirements 
    by this date or be subject to regulatory action. FDA also proposes that 
    any labeling changes necessary to reflect the adoption of ``tamper 
    evident`` terminology be made effective 2 years after the date of 
    publication of a final rule in the Federal Register.
    
    ADDRESSES: Submit written comments to the Dockets Management Branch 
    (HFA-305), Food and Drug Administration, rm. 1-23, 12420 Parklawn Dr., 
    Rockville, MD 20857.
    
    FOR FURTHER INFORMATION CONTACT: Howard P. Muller, Center for Drug 
    Evaluation and Research (HFD-362), Food and Drug Administration, 7500 
    Standish Pl., Rockville, MD 20855, 301-295-8049.
    
    SUPPLEMENTARY INFORMATION:
    
    I. Background
    
        FDA is proposing to amend its tamper-resistant packaging regulation 
    for OTC drug products in Sec. 211.132 (21 CFR 211.132). The regulation 
    requires that all OTC drug products (except dermatologics, dentifrices, 
    insulin, and throat lozenges) be in packaging designed to provide 
    consumers with visible evidence of any tampering that has occurred. FDA 
    first adopted these requirements in 1982 to respond to the public 
    health emergency in which seven persons in the Chicago area died after 
    taking cyanide-laced Extra-Strength Tylenol capsules (47 FR 50442, 
    November 5, 1982). Investigations showed that the cyanide had been 
    intentionally introduced into the capsules after they had reached the 
    retail shelf. Although the product's packaging met all FDA requirements 
    at the time, it was not designed so that tampering would leave visible 
    evidence. The poisoning fatalities illustrated the risk that consumers 
    of OTC drugs faced without such protective packaging. FDA met with 
    industry experts to explore ways to reduce this risk and to develop 
    specific recommendations for OTC drug packaging designs that would make 
    malicious tampering more obvious. These recommendations formed the 
    basis of the agency's initial regulatory approach.
        The 1982 regulation required that most OTC drug products be 
    packaged in a tamper-resistant package, which was defined in 
    Sec. 211.132(b) as packaging having an indicator or a barrier to entry 
    that could reasonably be expected to provide visible evidence to 
    consumers that tampering had occurred. In addition to meeting this 
    general standard, Sec. 211.132(b) required that the tamper-resistant 
    feature be distinctive by design or use a barrier to entry that 
    employed an identifying characteristic such as a logo. The regulation 
    further required that OTC product labeling alert consumers to the 
    specific packaging feature being employed (Sec. 211.132(c)). All 
    requirements of this regulation were in effect by February 6, 1984.
        FDA continued to monitor the effectiveness of its regulatory 
    program and found that, while the program had resulted in significant 
    improvements in protecting consumers from tampering harm, OTC products 
    marketed in two-piece, hard gelatin capsules remained vulnerable to 
    malicious tampering. In fact, all known fatalities from contaminated 
    OTC drugs, including three deaths in 1986--4 years after the tamper-
    resistant packaging requirements were first imposed--were associated 
    with this dosage form.
        Recognizing the persistent vulnerability of the hard capsule, the 
    agency amended its tamper-resistant packaging regulation in the Federal 
    Register of February 2, 1989 (54 FR 5227), to require that OTC products 
    marketed in two-piece, hard gelatin capsules be packaged using at least 
    two tamper-resistant features, unless the capsules were sealed using a 
    tamper-resistant technology (Sec. 211.132(b)(1) and (b)(2)). FDA 
    concluded that an additional packaging feature would reduce the dangers 
    posed by OTC drug tampering by making it more likely that the consumer 
    would see signs of tampering when it occurred. This requirement went 
    into effect on February 2, 1990.
        Even with this extra level of regulatory protection, two-piece, 
    hard gelatin capsules remain vulnerable to malicious tampering and have 
    been implicated in the latest fatalities. In February 1991, two persons 
    in the State of Washington died and another became gravely ill after 
    ingesting counterfeit Sudafed capsules contaminated with cyanide. The 
    capsules had been packaged using a number of tamper-resistant packaging 
    features that met FDA requirements. The tampering was crudely done and 
    left obvious signs: while both the counterfeit product and the Sudafed 
    product were in two-piece, hard gelatin capsules, the counterfeit 
    capsules were larger than the legitimate Sudafed capsules, lacked the 
    company logo and ``Sudafed`` imprint, and lacked the blue gelatin band 
    found on Sudafed capsules. In addition, the foil backing on the 
    package's blister card had been cut, and lot numbers on the blister 
    card did not match those on the carton. The contaminated capsules also 
    contained a yellowish powder, rather than the white granules contained 
    in Sudafed capsules.
        The Sudafed package and dosage form met FDA's tamper-resistant 
    standard, providing visible signs of tampering that were both numerous 
    and conspicuous. The fact that physical harm from the tampering 
    nonetheless occurred was of concern, and illustrated the need for a 
    renewed focus on consumer education and involvement in the 
    effectiveness of tamper-resistant or tamper-evident packaging. In 
    response to this most recent incident, the agency convened a task force 
    to review existing regulatory strategies and to consider what further 
    steps could be taken. The task force also considered information 
    provided by outside experts, including packaging scientists and 
    representatives of drug manufacturing trade associations. A number of 
    options were discussed, including banning the use of two-piece, hard 
    gelatin capsules for OTC drug products or restricting their 
    availability by requiring that they be kept behind the pharmacy 
    counter. These discussions balanced the value of the hard capsule 
    dosage form to consumers against its continued vulnerability to 
    malicious tampering. Memoranda from these discussions are on display in 
    the Dockets Management Branch (address above) and are available for 
    inspection between 9 a.m. and 4 p.m., Monday through Friday.
        During these discussions, FDA gave serious consideration to banning 
    the use of two-piece, hard gelatin capsules, but has tentatively 
    concluded that such capsules should remain available for several 
    reasons. First, FDA believes that banning hard gelatin capsules because 
    they have been associated with tampering may give consumers a false 
    sense of security that tampering with other dosage forms could no 
    longer occur. Second, FDA believes that a ban would deprive the public 
    of a useful dosage form. The Nonprescription Drug Manufacturers 
    Association (NDMA)\1\ indicated that the two-piece, hard gelatin 
    capsule can have certain features not provided by other dosage forms 
    that are currently available. For example, many consumers prefer to 
    take capsules, finding them easiest to swallow. In addition, some 
    medications can only be formulated in the capsule dosage form, due to 
    detrimental effects on active ingredients from tableting or other 
    formulation processes. Hard gelatin capsules also may contain fewer 
    inactive ingredients, which can cause allergic reactions in some 
    individuals, than some tablet and oral liquid formulations. Moreover, 
    the hard gelatin capsule dosage form is sometimes necessary to deliver 
    timed-release medications. Given the potential benefits of capsules, 
    FDA believes that, at this time, it is appropriate to seek to decrease 
    the risks posed by product tampering through means other than banning 
    two-piece, hard gelatin capsules.
    ---------------------------------------------------------------------------
    
        \1\The NDMA position statement entitled ``The Sale of OTC 
    Medicines in Capsule Form Should Not Be Banned or Restricted'' is on 
    display in the Dockets Management Branch (address above) and is 
    available for inspection between 9 a.m. and 4 p.m., Monday through 
    Friday.
    ---------------------------------------------------------------------------
    
        This proposed rule is based on investigations and discussions 
    surrounding the 1991 tampering fatalities, as well as FDA's ongoing 
    review of the public health threat from OTC drug product tampering. The 
    proposal suggests some specific regulatory measures for reducing the 
    potential for tampering with the vulnerable hard capsule dosage form. 
    It also presents additional ideas for improving the effectiveness of 
    current policies directed against product tampering and invites public 
    discussion and comment on these ideas. By proposing the regulatory 
    changes and encouraging a dialogue on the subject of improving anti-
    tampering measures and involvement of the consumer, the agency hopes to 
    increase protection of the public against malicious tampering.
    
    A. Description of the Proposed Rule
    
        FDA is proposing to amend its tamper-resistant packaging regulation 
    to decrease the potential for harm from tampering involving two-piece, 
    hard gelatin capsules. FDA also proposes to take certain steps to focus 
    the attention of all parties on the need to make consumers aware of the 
    special packaging features that indicate that tampering has occurred. 
    The proposed changes complement a number of other actions that FDA is 
    taking both to improve consumer awareness and to encourage the 
    development of better packaging technologies.
        One proposed change would amend the current regulation that 
    establishes specific requirements for OTC products marketed in two-
    piece, hard gelatin capsules. As noted, this dosage form has been 
    subject to the most serious tampering incidents over the years. The 
    regulation now requires that these products be packaged using a minimum 
    of two tamper-resistant packaging features, unless the capsules are 
    sealed by a tamper-resistant technology, in which case, one packaging 
    feature is sufficient (Sec. 211.132(b)(1) and (b)(2)). Proposed 
    revisions to Sec. 211.132(b)(2) would require that any OTC drug product 
    marketed in a two-piece, hard gelatin capsule be sealed using a 
    technology that would provide evidence that the capsule has been 
    tampered with after filling. (Some capsule sealing technologies are 
    described in FDA's Compliance Policy Guide 7132a.17.\2\) The proposed 
    rule would no longer require that such products be packaged in a 
    container with two tamper-resistant packaging features. The proposed 
    rule would require that the sealed capsules be in packaging employing a 
    minimum of one tamper-resistant feature, the requirement that applies 
    to all other affected OTC dosage forms. The agency believes that 
    requiring OTC capsules to be sealed may decrease the likelihood that 
    successful product tampering will occur with this dosage form. This 
    proposed change would not apply to one-piece, soft gelatin capsules, 
    also known as soft gels. FDA specifically requests comments on whether 
    the proposed requirement to seal all two-piece, hard gelatin capsules 
    would adversely affect any patient population or specific drug entity 
    or drug class.
    ---------------------------------------------------------------------------
    
        \2\Compliance Policy Guide 7132a.17 is available from the 
    National Technical Information Service (NTIS), United States 
    Department of Commerce, 5285 Port Royal Rd., Springfield, VA 22161, 
    703-487-4650.
    ---------------------------------------------------------------------------
    
        The agency is also proposing that the term used to describe the 
    packaging requirements be changed from ``tamper-resistant'' to 
    ``tamper-evident.'' FDA believes that the term ``tamper-evident'' more 
    accurately describes the role of packaging in reducing the likelihood 
    of harm from tampering, and emphasizes the necessity of consumer 
    involvement in the effectiveness of any packaging system designed to 
    meet the requirements of the regulation.
        The change in terminology is intended to underscore the view that 
    no package design is tamper-proof. The packaging of the Sudafed 
    capsules did not prevent the 1991 tampering incidents, although it met 
    FDA requirements and the evidence of tampering was strikingly visible. 
    The proposed adoption of ``tamper-evident'' terminology should remind 
    all parties that the success of these regulatory initiatives depends 
    significantly on consumer vigilance. The proposed rule would also 
    revise Sec. 211.132(c) to clarify the requirements for the tamper-
    evident packaging labeling statement. By alerting consumers to the 
    particular tamper-evident packaging features used, the labeling 
    statement plays a crucial role in the effectiveness of any tamper-
    evident packaging system. Consumers who are alerted and aware of all 
    packaging features used are in the best position to detect the evidence 
    of tampering that the package has been designed to provide.
         Current Sec. 211.132(c) states that each retail package ``* * * is 
    required to bear a statement that is prominently placed so that 
    consumers are alerted to the specific tamper-resistant feature of the 
    package.'' Some firms have interpreted this as requiring the labeling 
    statement to refer only to tamper-evident features on the external 
    package. Proposed Sec. 211.132(c) would clarify that, in order to alert 
    consumers to the tamper-evident packaging features used, the labeling 
    statement must identify all packaging features used to comply with 
    proposed Sec. 211.132(b)(1), including those on the secondary package, 
    those on the immediate container or closure, and any capsule sealing 
    technologies that are employed to meet the requirements of proposed 
    Sec. 211.132(b)(2).
        The proposed rule would also revise Sec. 211.132(b) and (c) to 
    remove reference to OTC products in aerosol containers, which are 
    inherently resistant to tampering, but not appropriately considered in 
    a discussion of tamper-evident packaging.
        The proposed rule would also amend Sec. 211.132(a) and (b) to 
    replace the term ``throat lozenge'' with ``lozenge.'' FDA is making 
    this change because the tamper-evident packaging requirements should 
    apply to all lozenges, not just throat lozenges. The agency also notes 
    that the proposed change is consistent with earlier tamper-resistant 
    packaging regulations (see 48 FR 16658 at 16664, April 19, 1983).
    
    B. Legal Authority
    
        This proposal is authorized in part by sections of the Federal 
    Food, Drug, and Cosmetic Act (the act) concerning imposition of 
    requirements necessary to assure that drugs meet the requirements of 
    the act for identity, strength, quality, and purity. These requirements 
    may be imposed as current good manufacturing practice under section 
    501(a)(2)(B) of the act (21 U.S.C. 351(a)(2)(B)) and in aid of other 
    statutory requirements relating to product safety and integrity. (See, 
    e.g., 21 U.S.C. 351(b) and (c) and section 701 (21 U.S.C. 371(a)) of 
    the act.) This statutory authorization permits promulgation of 
    requirements for container and package design that provide protection 
    against intentional product adulteration by means of tampering.
         Promulgating requirements for labeling statements alerting drug 
    product consumers to tamper-evident features is authorized under the 
    adulteration provisions in section 501 and under the provisions in 
    sections 502 and 201(n) of the act (21 U.S.C. 352(c) and 321(n)). The 
    labeling statements are necessary to assure the effectiveness of the 
    tamper-evident features; without such statements the products would be 
    adulterated. In addition, under section 502(c) of the act, products are 
    misbranded if statements required under other authority in the act are 
    omitted from the products' labeling. Moreover, under sections 201(n) 
    and 502(a) of the act, products may be misbranded by reason of the 
    omission of material facts about the products, such as the tamper-
    evident features. (See 47 FR 50442 at 50447, November 5, 1982, for 
    additional discussion of the legal authority for requirements related 
    to drug product tampering.)
    
    II. Other Consumer Protection Initiatives
    
    A. Consumer Education
    
        The 1991 tampering fatalities made clear that the OTC drug supply 
    is still vulnerable to malicious tampering. As noted, FDA's 
    deliberations following these fatalities focused on reevaluating 
    current strategies to reduce the likelihood of harm from tampering and 
    looking at the role that FDA, industry, and consumers play in their 
    success or failure. While the agency will consider whether additional 
    changes to the regulations may be needed to reduce the risks posed by 
    product tampering, FDA believes that further initiatives will 
    increasingly focus on consumer education and involvement.
         FDA has already taken steps to inform consumers about the need to 
    be alert for drug product tampering. FDA has worked closely with NDMA 
    to develop and disseminate public service announcements about 
    tampering. These are being provided to general circulation magazines 
    and other publications. In addition, the October 1991 issue of FDA 
    Consumer contained an article entitled ``Look Twice,'' which explains 
    the danger posed by drug product tampering and the need for consumer 
    vigilance. Similar information appears in materials cosponsored by FDA 
    and NDMA including a brochure called ``Buying Medicine?: Stop, Look, 
    Look Again'' and a video and audio tape on product tampering entitled 
    ``Take A Look,'' which has been distributed to the media. FDA is also 
    considering sponsoring workshops around the country to inform the 
    public about tamper-evident packaging and the safety of the OTC drug 
    supply. FDA solicits comments and suggestions from the public on ways 
    to improve this educational campaign.
    
    B. Research Into Consumer Behavior
    
        The regulatory strategies FDA has adopted have been based on 
    certain assumptions about how consumers behave when buying and taking 
    their OTC drug products. To choose the most effective measures to 
    enable consumers to detect tampering, it is necessary to have more and 
    better information about how consumers select, purchase, and use OTC 
    drug products and how tamper-evident packaging and associated labeling 
    affects their behavior. FDA is aware of some research in this area, 
    including studies done at Michigan State University, Rutgers 
    University, and other academic institutions. Although such research has 
    provided useful starting points for discussions of tamper-evident 
    packaging, FDA believes that further research is needed to permit the 
    design of more effective packaging features and educational campaigns. 
    FDA is interested in learning more about any current consumer research 
    that is relevant to the concerns of this rulemaking. FDA is also 
    willing to assist any industry group or other interested party in the 
    design and development of research in this area.
    
    C. Private Initiatives
    
        As noted, the agency has taken several steps to encourage the use 
    of safer packaging technologies. FDA believes that these steps can be 
    complemented by actions of drug manufacturers and other interested 
    persons. The agency initiatives in 1982 were taken with the knowledge 
    that certain packaging technologies, including, for example, film 
    wrappers, blister or strip packs, and heat shrink bands or wrappers, 
    were available to drug manufacturers to reduce the risk of tampering. 
    The agency notes that few new technologies have been added since 1982. 
    The agency recognizes that no package is tamper-proof but believes that 
    there are opportunities for innovations and for refinement of current 
    designs to improve consumer protection. FDA encourages both individual 
    and collective efforts in the OTC drug and packaging industry to devise 
    better technologies.
        FDA would also like to discuss with the drug industry and other 
    interested persons the possibility of establishing performance 
    standards for tamper-evident packaging. Such standards might be based 
    on the probability that a consumer could detect evidence of tampering 
    with a given packaging design. Compliance with the standards might be 
    measured by studying the likelihood that a consumer would recognize 
    signs of tampering within a specified amount of time. Where a packaging 
    feature is to be used on a product targeted to or frequently purchased 
    by a particular group of consumers, such as the elderly, the level of 
    recognition might be determined using a representative number of the 
    particular group.
        Developing performance standards based, in part, on the behavior 
    and reaction of consumers to product packaging would be challenging. 
    FDA believes, however, that it is not an impossible task, and suggests 
    that information from the research and development of package design 
    from a marketing standpoint might be useful. Furthermore, the agency 
    believes that any performance standards for tamper-evident packaging 
    should be based on the latest behavioral and technological information 
    available. Such state-of-the-art standards would give packaging 
    engineers and manufacturers a benchmark for evaluating particular 
    package designs, and would provide an incentive to improve the 
    effectiveness of tamper-evident packaging to mirror technological 
    progress in the field. The agency invites comments on the 
    appropriateness of developing and requiring performance standards for 
    tamper-evident packaging.
    
    III. Economic Impact
    
        FDA has carefully considered the economic impact of this proposed 
    rule and has determined that it requires neither a regulatory impact 
    analysis, as specified by Executive Order 12291, nor a regulatory 
    flexibility analysis, as defined in the Regulatory Flexibility Act 
    (Pub. L. 96-354). The agency believes that the proposed rule, if 
    finalized, would generate costs that are well below the thresholds that 
    would signify a major rule, and so the proposed rule does not require a 
    regulatory impact analysis. The agency also finds that the proposed 
    rule would not have a significant effect on a substantial number of 
    small entities, and therefore does not require a regulatory flexibility 
    analysis.
        Current FDA requirements for OTC drug packaging to protect the 
    public from the threat of product tampering have been in place since 
    1982. This proposed rule would not change the scope or applicability of 
    these requirements, but would only amend the requirements with regard 
    to one OTC drug dosage form and impose a minor labeling change that 
    would affect certain products.
        This proposed rule may impose additional costs on manufacturers who 
    choose to market their OTC drug products in two-piece, hard gelatin 
    capsules instead of switching to a different dosage form, such as a 
    soft-gel or liquid-gel capsule, or a caplet. The proposed rule would 
    delete the current requirement that two-piece, hard gelatin capsules be 
    packaged using two tamper-evident features, and would require instead 
    that all such capsules be sealed and packaged using at least one 
    tamper-evident feature. FDA believes that capsule sealing would make it 
    more difficult to tamper with this dosage form without leaving visible 
    evidence, and that any costs resulting from the rule would be small 
    compared to public health benefits from this added measure of consumer 
    protection.
        The number of two-piece, hard gelatin capsule OTC products sold 
    over the last few years has declined dramatically, with fewer than 50 
    such items currently listed with FDA. A review of those products 
    indicates that from 75 percent to 90 percent are already sealed or 
    ``banded.'' Thus, FDA is aware of only a small number of OTC products 
    still marketed as unsealed two-piece, hard gelatin capsules. Under the 
    proposed rule, the few firms producing these products would have to 
    choose between incurring costs for reformulating the product to a 
    different dosage form or installing machinery needed to seal the two-
    piece, hard gelatin capsules. The affected firms would not face 
    substantial added costs for lost product inventory because the proposed 
    rule allows manufacturers 1 year and retailers 2 years after the date 
    of publication of a final rule to effect the changes.
         NDMA estimates that the approximate cost of a capsule sealing or 
    banding machine ranges from $150,000 to $250,000. Assuming FDA's higher 
    bound estimate that only 25 percent of the 50 listed, two-piece, hard 
    gelatin capsule products are not currently sealed with an appropriate 
    technology, then 12 products would need to be sealed or banded. If only 
    one new capsule banding machine were needed per product, the total cost 
    to the industry would range from $1.8 million to $3 million. An 
    additional cost may occur if it is difficult for a company to integrate 
    the sealing equipment into its capsule filling line. According to NDMA, 
    some companies may find that this problem adds an extra cost of 
    approximately 50 cents to 80 cents per 1,000 capsules. Nonetheless, for 
    all but the smallest product lines, these costs would be a modest 
    percentage of sales. The proposed rule would also change regulatory 
    terminology from ``tamper-resistant'' packaging to ``tamper-evident'' 
    packaging. This would affect a substantial number of firms because it 
    would necessitate a labeling change under Sec. 211.132(c) for all OTC 
    products that now have the words ``tamper-resistant'' on their package. 
    A small survey conducted by FDA found that approximately 60 percent of 
    OTC drug product labels include the words ``tamper-resistant.'' The 
    remaining product labels include a description of tamper-resistant 
    packaging features, but do not specifically use the words ``tamper-
    resistant.''
         In 1986, NDMA estimated that about 70 percent of their members' 
    435 products, excluding private labelers, were affected by tamper-
    resistant packaging regulations. On the assumption that there were 
    three shelf keeping units (SKU's) per product, this amounted to about 
    1,300 SKU's. Based on a 1986 survey of its members, NDMA had reported 
    that the average labeling change cost per SKU was $3,000 to $4,000. The 
    current proposal, however, would require a much simpler label change 
    than was considered in that 1986 survey. Nonetheless, if the cost per 
    SKU were assumed to be about $3,000, the total cost of changing 60 
    percent of these labels would be approximately $2.3 million (60 percent 
    x 1,300 x $3,000). In addition, NDMA provided a preliminary estimate of 
    $5 million for 15 larger private labeling companies. Sixty percent of 
    this cost amounts to $3 million. Thus, the potential upper-bound cost 
    imposed by the proposed labeling changes may amount to $5 to $6 
    million.
        The actual cost of the labeling change would be significantly 
    lessened by FDA's proposed effective date for the labeling change, 
    which would give manufacturers up to 2 years from the date of 
    publication of a final rule to make the required changes. The agency 
    chose this timeframe to minimize the burden to industry of converting 
    to ``tamper-evident'' terminology, based on information from NDMA that 
    most product labels are routinely reprinted within an 18- to 24-month 
    period. Thus, although FDA does not know the precise number of OTC 
    product labels that are normally reprinted within a 2-year period, the 
    labeling costs attributable to the proposed regulation would be minimal 
    for most firms in this industry.
        To summarize, the total one-time costs of this proposed rule would 
    be the sum of the approximately $3 million to seal or band the 
    remaining few two-piece, hard gelatin capsule products and the minimal 
    costs needed to change the labeling on the products that currently read 
    ``tamper-resistant.''
         In addition to these regulatory changes, FDA has invited comments 
    on other initiatives such as the development of better consumer 
    education campaigns, research into consumer behavior with regard to OTC 
    packaging and tamper-evident packaging, and the possibility of 
    developing performance standards for tamper-evident packaging. Any of 
    these programs, if adopted as regulatory requirements, could have 
    significant economic importance. Before promulgating any final 
    regulation, however, FDA intends to consider all relevant information 
    on the economic consequences of these initiatives and reasonable 
    alternatives. The agency solicits public comment on all aspects of both 
    the costs and feasibility of all issues raised by this proposal, 
    especially with respect to any impact on affected small businesses.
    
    IV. Executive Order 12612--Federalism
    
        Executive Order 12612 requires that Federal agencies carefully 
    examine regulatory actions to determine if they would have significant 
    federalism implications. FDA's tamper-resistant packaging regulations 
    were issued with the intent that the regulations preempt State and 
    local packaging requirements that are not identical to the Federal 
    requirements in all respects (47 FR 50442 at 50447, November 5, 1992). 
    The agency believes that the proposed changes would improve safeguards 
    to protect consumers from tampering of all OTC drug products, 
    particularly those marketed as two-piece, hard gelatin capsules, and 
    that the amendments, therefore, should eliminate the need for 
    additional action at the State or local level. FDA invites comments on 
    the adequacy of the proposed amendments in this regard.
    
    V. Environmental Impact
    
        The agency has determined under 21 CFR 25.24(a)(11) that this 
    action is of a type that does not individually or cumulatively have a 
    significant effect on the human environment. Therefore, neither an 
    environmental assessment nor an environmental impact statement is 
    required.
    
    VI. Request for Comments
    
        Interested persons may, on or before March 21, 1994, submit to the 
    Dockets Management Branch (address above) written comments regarding 
    this proposal. Two copies of any comments are to be submitted, except 
    that individuals may submit one copy. Comments are to be identified 
    with the docket number found in brackets in the heading of this 
    document. Received comments may be seen in the office above between 9 
    a.m. and 4 p.m., Monday through Friday.
    
    VII. Proposed Effective Dates
    
        FDA proposes that any final rule based on the proposed requirement 
    that all OTC drug products marketed as two-piece, hard gelatin capsules 
    be sealed be made effective 1 year after its date of publication in the 
    Federal Register. All OTC drug products marketed as two-piece, hard 
    gelatin capsules that are initially introduced or initially delivered 
    for introduction into interstate commerce on or after the effective 
    date must be sealed according to the requirements of the final rule or 
    be subject to regulatory action. FDA also proposes a retail level 
    effective date for this requirement of 2 years after the date of 
    publication of a final rule in the Federal Register. After this date, 
    all two-piece, hard gelatin capsule products held for sale (including 
    stocks in retail stores) must be sealed according to the requirements 
    of the final rule or be subject to regulatory action.
        FDA also proposes that any labeling changes necessary to reflect 
    the adoption of ``tamper-evident'' terminology be made within 2 years 
    after the date of publication of a final rule in the Federal Register. 
    Based on information from industry, FDA expects that most products 
    subject to tamper-evident packaging requirements will have undergone 
    routine labeling revisions within this timeframe.
    
    List of Subjects in 21 CFR Part 211
    
        Drugs, Labeling, Laboratories, Packaging and containers, 
    Prescription drugs, Reporting and recordkeeping requirements, 
    Warehouses.
        Therefore, under the Federal Food, Drug, and Cosmetic Act and under 
    authority delegated to the Commissioner of Food and Drugs, it is 
    proposed that 21 CFR part 211 be amended as follows:
    
    PART 211--CURRENT GOOD MANUFACTURING PRACTICE FOR FINISHED 
    PHARMACEUTICALS
    
        1. The authority citation for 21 CFR part 211 continues to read as 
    follows:
    
        Authority: Secs. 201, 501, 502, 505, 506, 507, 512, 701, 704 of 
    the Federal Food, Drug, and Cosmetic Act (21 U.S.C. 321, 351, 352, 
    355, 356, 357, 360b, 371, 374).
    
        2. Section 211.132 is amended by revising the section heading, by 
    removing in paragraph (a) the word ``throat'', by removing in 
    paragraphs (a) and (d)(2) the words ``tamper-resistant'' and adding in 
    their place the words ``tamper-evident'', and by revising paragraphs 
    (b), (c), and the second sentence in the introductory text of paragraph 
    (d) to read as follows:
    
    
    Sec. 211.132  Tamper-evident packaging requirements for over-the-
    counter (OTC) human drug products.
    
    *     *     *     *     *
         (b) Requirements for tamper-evident package. (1) Each manufacturer 
    and packer who packages an OTC drug product (except a dermatological, 
    dentifrice, insulin, or lozenge product) for retail sale shall package 
    the product in a tamper-evident package, if this product is accessible 
    to the public while held for sale. A tamper-evident package is one 
    having one or more indicators or barriers to entry which, if breached 
    or missing, can reasonably be expected to provide visible evidence to 
    consumers that tampering has occurred. To reduce the likelihood of 
    successful tampering and to increase the likelihood that consumers will 
    discover if a product has been tampered with, the package is required 
    to be distinctive by design or by the use of one or more indicators or 
    barriers to entry that employ an identifying characteristic (e.g., a 
    pattern, name, registered trademark, logo, or picture). For purposes of 
    this section, the term ``distinctive by design'' means the packaging 
    cannot be duplicated with commonly available processes. A tamper-
    evident package may involve an immediate-container and closure system 
    or secondary-container or carton system or any combination of systems 
    intended to provide a visual indication of package integrity. The 
    tamper-evident feature shall be designed to and shall remain intact 
    when handled in a reasonable manner during manufacture, distribution, 
    and retail display.
        (2) In addition to the tamper-evident packaging feature described 
    in paragraph (b)(1) of this section, any two-piece, hard gelatin 
    capsule covered by this section must be sealed using an acceptable 
    tamper-evident technology.
        (c) Labeling. (1) In order to alert consumers to the specific 
    tamper-evident feature(s) used, each retail package of an OTC drug 
    product covered by this section (except ammonia inhalant in crushable 
    glass ampules or containers of compressed medical oxygen) is required 
    to bear a statement that:
        (i) Identifies all tamper-evident feature(s) and any capsule 
    sealing technologies used to comply with paragraph (b) of this section;
        (ii) Is prominently placed on the package; and
        (iii) Is so placed that it will be unaffected if the tamper-evident 
    feature of the package is breached or missing.
        (2) If the tamper-evident feature chosen to meet the requirements 
    in paragraph (b) of this section uses an identifying characteristic, 
    that characteristic is required to be referred to in the labeling 
    statement. For example, the labeling statement on a bottle with a 
    shrink band could say ``For your protection, this bottle has an 
    imprinted seal around the neck.''
        (d) *  *  * A request for an exemption is required to be submitted 
    in the form of a citizen petition under Sec. 10.30 of this chapter and 
    should be clearly identified on the envelope as a ``Request for 
    Exemption from the Tamper-Evident Packaging Rule.'' * * *
    *     *     *      *     *
    
        Dated: September 13, 1993.
    Michael R. Taylor,
    Deputy Commissioner for Policy.
    [FR Doc. 94-1049 Filed 1-14-94; 8:45 am]
    BILLING CODE 4160-01-F