-
Start Preamble
AGENCY:
Federal Aviation Administration (FAA), DOT.
ACTION:
Notice of proposed rulemaking (NPRM).
SUMMARY:
We propose to adopt a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702), CL-600-2D15 (Regional Jet Series 705), CL-600-2D24 (Regional Jet Series 900), and CL-600-2E25 (Regional Jet Series 1000) airplanes. This proposed AD was prompted by the finding of an uncertified main landing gear (MLG) inboard retraction actuator bracket pin installed on an in-service airplane, which could result in pin failure. This proposed AD would require inspection of the MLG inboard retraction actuator bracket for a part number, and replacement if necessary. We are proposing this AD to detect and correct uncertified pins in the MLG inboard retraction actuator bracket, which could result in pin failure, leading to an MLG extension without damping, and a potential for MLG structural damage and possible collapse during landing.
DATES:
We must receive comments on this proposed AD by February 18, 2014.
ADDRESSES:
You may send comments by any of the following methods:
- Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
- Fax: (202) 493-2251.
- Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590.
- Hand Delivery: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.
For service information identified in this proposed AD, contact Bombardier, Inc., 400 Côte-Vertu Road West, Dorval, Québec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-7401; email thd.crj@aero.bombardier.com; Internet http://www.bombardier.com. You may view this referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425-227-1221.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov;; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the MCAI, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.
Start Further InfoFOR FURTHER INFORMATION CONTACT:
Luke Walker, Aerospace Engineer, Airframe and Mechanical Systems Branch, ANE 171, FAA, New York Aircraft Certification Office (ACO), 1600 Stewart Avenue, Suite 410, Westbury, New York 11590; telephone 516-228-7363; fax 516-794-5531.
End Further Info End Preamble Start Supplemental InformationSUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include “Docket No. FAA-2013-1070; Directorate Identifier 2013-NM-175-AD” at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments.
We will post all comments we receive, without change, to http://www.regulations.gov,, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD.Start Printed Page 73
Discussion
Transport Canada Civil Aviation (TCCA), which is the aviation authority for Canada, has issued Canadian Airworthiness Directive CF-2013-23, dated August 13, 2013 (referred to after this as the Mandatory Continuing Airworthiness Information, or “the MCAI”), to correct an unsafe condition for the specified products. The MCAI states:
An uncertified main landing gear (MLG) inboard retraction actuator bracket pin, part number (P/N) 49131-1, was found installed on an in-service aeroplane. Five other uncertified pins were also returned to the manufacturer. The uncertified pin, P/N 49131-1, is weaker than the approved pin, P/N 49131-3. An MLG inboard retraction actuator bracket pin failure could result in an MLG extension without damping, and a potential for MLG structural damage and possible collapse during landing.
This [TCCA] AD mandates the inspection for and removal of the uncertified pins.
You may examine the MCAI in the AD docket on the Internet at http://www.regulations.gov by searching for and locating it in Docket No. FAA-2013-1070.
Relevant Service Information
Bombardier has issued Service Bulletin 670BA-32-044, dated May 29, 2013. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI.
FAA's Determination and Requirements of This Proposed AD
This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design.
Costs of Compliance
We estimate that this proposed AD affects 416 airplanes of U.S. registry.
We also estimate that it would take about 1 work-hour per product to comply with the basic requirements of this proposed AD. The average labor rate is $85 per work-hour. Required parts would cost about $0 per product. Based on these figures, we estimate the cost of this proposed AD on U.S. operators to be $35,360, or $85 per product.
In addition, we estimate that any necessary follow-on actions would take about 1 work-hour and require parts costing $0, for a cost of $85 per product. We have no way of determining the number of aircraft that might need this action.
According to the manufacturer, some of the costs of this proposed AD may be covered under warranty, thereby reducing the cost impact on affected individuals. We do not control warranty coverage for affected individuals. As a result, we have included all costs in our cost estimate.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. “Subtitle VII: Aviation Programs,” describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in “Subtitle VII, Part A, Subpart III, Section 44701: General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
Regulatory Findings
We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed regulation:
1. Is not a “significant regulatory action” under Executive Order 12866;
2. Is not a “significant rule” under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979);
3. Will not affect intrastate aviation in Alaska; and
4. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
Start List of SubjectsList of Subjects in 14 CFR Part 39
- Air transportation
- Aircraft
- Aviation safety
- Incorporation by reference
- Safety
The Proposed Amendment
Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
Start PartPART 39—AIRWORTHINESS DIRECTIVES
End Part Start Amendment Part1. The authority citation for part 39 continues to read as follows:
End Amendment Part[Amended]2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD):
End Amendment PartBombardier, Inc.: Docket No. FAA-2013-1070; Directorate Identifier 2013-NM-175-AD.
(a) Comments Due Date
We must receive comments by February 18, 2014.
(b) Affected ADs
None.
(c) Applicability
This AD applies to the airplanes identified in paragraphs (c)(1), (c)(2), and (c)(3) of this AD, certificated in any category.
(1) Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) airplanes, serial number (S/N) 10002 and subsequent.
(2) Bombardier, Inc. Model CL-600-2D15 (Regional Jet Series 705); and CL-600-2D24 (Regional Jet Series 900) airplanes; S/N 15001 and subsequent.
(3) Bombardier, Inc. Model CL-600-2E25 (Regional Jet Series 1000) airplanes, S/N 19001 and subsequent.
(d) Subject
Air Transport Association (ATA) of America Code 32, Landing Gear.
(e) Reason
This AD was prompted by the finding of an uncertified main landing gear (MLG) inboard retraction actuator bracket pin installed on an in-service airplane, which could result in pin failure. We are issuing this AD to detect and correct uncertified pins in the MLG inboard retraction actuator bracket, which could result in pin failure, leading to an MLG extension without damping, and a potential for MLG structural damage and possible collapse during landing.
(f) Compliance
You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done.
(g) Inspection
Within 6,600 flight hours or 36 months after the effective date of this AD, whichever Start Printed Page 74occurs first, do an inspection of the MLG inboard retraction actuator bracket for any uncertified pin having part number (P/N) 49131-1, in accordance with the Accomplishment Instructions of Bombardier Service Bulletin 670BA-32-044, dated May 29, 2013.
(h) Replacement
If any uncertified pin having P/N 49131-1 is found during the inspection required by paragraph (g) of this AD, before further flight, replace all uncertified pins, in accordance with the Accomplishment Instructions of Bombardier Service Bulletin 670BA-32-044, dated May 29, 2013.
(i) Other FAA AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, ANE-170, FAA, New York Aircraft Certification Office (ACO), 1600 Stewart Avenue, Suite 410, Westbury, New York 11590; telephone 516-228-7363; fax 516-794-5531, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the NYACO, send it to ATTN: Program Manager, Continuing Operational Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. The AMOC approval letter must specifically reference this AD.
(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they were approved by the State of Design Authority (or its delegated agent, or by the DAH with a State of Design Authority's design organization approval). For a repair method to be approved, the repair approval must specifically refer to this AD. You are required to ensure the product is airworthy before it is returned to service.
(j) Related Information
(1) Refer to Mandatory Continuing Airworthiness Information Canadian Airworthiness Directive CF-2013-23, dated August 13, 2013, for related information. This MCAI may be found in the AD docket on the Internet at http://www.regulations.gov by searching for and locating it in Docket No. FAA-2013-1070.
(2) For service information identified in this AD, contact Bombardier, Inc., 400 Côte-Vertu Road West, Dorval, Québec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-7401; email thd.crj@aero.bombardier.com; Internet http://www.bombardier.com. You may view this service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425-227-1221.
Start SignatureIssued in Renton, Washington, on December 20, 2013.
Jeffrey E. Duven,
Manager, Transport Airplane Directorate, Aircraft Certification Service.
[FR Doc. 2013-31301 Filed 12-31-13; 8:45 am]
BILLING CODE 4910-13-P
Document Information
- Published:
- 01/02/2014
- Department:
- Federal Aviation Administration
- Entry Type:
- Proposed Rule
- Action:
- Notice of proposed rulemaking (NPRM).
- Document Number:
- 2013-31301
- Dates:
- We must receive comments on this proposed AD by February 18, 2014.
- Pages:
- 72-74 (3 pages)
- Docket Numbers:
- Docket No. FAA-2013-1070, Directorate Identifier 2013-NM-175-AD
- RINs:
- 2120-AA64: Airworthiness Directives
- RIN Links:
- https://www.federalregister.gov/regulations/2120-AA64/airworthiness-directives
- Topics:
- Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety
- PDF File:
- 2013-31301.pdf
- CFR: (1)
- 14 CFR 39.13