E7-817. Agency Information Collection Activities; Submission to OMB for Review and Approval; Comment Request; NESHAP for Plastic Parts and Products Surface (Renewal); EPA ICR Number 2044.03; OMB Control Number 2060-0537

AGENCY:

Environmental Protection Agency.

ACTION:

Notice.

SUMMARY:

In compliance with the Paperwork Reduction Act (PRA) (44 U.S.C. 3501 et seq.), this document announces that an Information Collection Request (ICR) has been forwarded to the Office of Management and Budget (OMB) for review and approval. This is a request to renew an existing approved collection. The ICR which is abstracted below describes the nature of the information collection and its estimated burden and cost.

DATES:

Additional comments may be submitted on or before February 21, 2007.

ADDRESSES:

Submit your comments, referencing docket ID number EPA-HQ-OECA-2006-0433, to (1) EPA online using www.regulations.gov (our preferred method), by e-mail to [e-mail], or by mail to: EPA Docket Center (EPA/DC), Environmental Protection Agency, Enforcement and Compliance Docket and Information Center, mail code 2201T, 1200 Pennsylvania Avenue, NW., Washington, DC 20460, and (2) OMB at: Office of Information and Regulatory Affairs, Office of Management and Budget (OMB), Attention: Desk Officer for EPA, 725 17th Street, NW., Washington, DC 20503.

FOR FURTHER INFORMATION CONTACT:

Leonard Lazarus, Compliance Assessment and Media Programs Division (CAMPD), Office of Compliance, (2223A), Environmental Protection Agency, 1200 Pennsylvania Avenue, NW., Washington, DC 20460; telephone number: [phone]; fax number: [phone]; e-mail address: [e-mail].

SUPPLEMENTARY INFORMATION:

EPA has submitted the following ICR to OMB for review and approval according to the procedures prescribed in 5 CFR 1320.12. On June 21, 2006 (71 FR 35652), EPA sought comments on this ICR pursuant to 5 CFR 1320.8(d). EPA received no comments. Any additional comments on this ICR should be submitted to EPA and OMB within 30 days of this notice.

EPA has established a public docket for this ICR under docket ID number EPA-HQ-OECA-2006-0433, which is available for online viewing at http://www.regulations.gov,, in person viewing at the Enforcement and Compliance Docket and Information Center in the EPA Docket Center (EPA/DC), EPA West, Room 3334, 1301 Constitution Avenue, NW., Washington, DC. The EPA/DC Public Reading Room is open from 8 a.m. to 4:30 p.m., Monday through Friday, excluding legal holidays. The telephone number for the Reading Room is [phone], and the telephone number for the Enforcement and Compliance Docket and Information Center Docket is [phone].

Use EPA's electronic docket and comment system at http://www.regulations.gov,, to submit or view public comments, access the index listing of the contents of the docket, and to access those documents in the docket that are available electronically. Once in the system, select “docket search,” then key in the docket ID number identified above. Please note that EPA's policy is that public comments, whether submitted electronically or in paper, will be made available for public viewing at http://www.regulations.gov as EPA receives them and without change, unless the comment contains copyrighted material, CBI, or other information whose public disclosure is restricted by statute. For further information about the electronic docket, go to http://www.regulations.gov.

Title: NESHAP for Plastic Parts and Products Surface Coating (Renewal).

ICR Numbers: EPA ICR Number 2044.03, OMB Control Number 2060-0537.

ICR Status: This ICR is scheduled to expire on January 31, 2007. Under OMB regulations, the Agency may continue to conduct or sponsor the collection of information while this submission is pending at OMB. An Agency may not conduct or sponsor, and a person is not required to respond to, a collection of information, unless it displays a currently valid OMB control number. The OMB control numbers for EPA's regulations in title 40 of the CFR, after appearing in the Federal Register when approved, are listed in 40 CFR part 9, are displayed either by publication in the Federal Register or by other appropriate means, such as on the related collection instrument or form, if applicable. The display of OMB control numbers in certain EPA regulations is consolidated in 40 CFR part 9.

Abstract: Respondents are owners, or operators of plastic parts and products surface coating operations. Owners, or operators of the affected facilities described must make initial reports when a source becomes subject to the standard, conduct and report on a performance test, demonstrate and report on continuous monitor performance, and maintain records of the occurrence and duration of any startup, shutdown, or malfunction in the operation of an affected facility. Semiannual reports of excess emissions are required. These notifications, reports, and records are essential in determining compliance and are required, in general, of all sources subject to National Emission Standards for Hazardous Air Pollutants (NESHAP). Any owner, or operator subject to the provisions of this part shall maintain a file of these measurements and retain the file for at least five years following the date of such measurements, maintenance reports, and records. All reports are sent to the delegated state, or local authority. In the event that there is no such delegated authority, the reports are sent directly to the EPA regional office.

An agency may not conduct, or sponsor, and a person is not required to respond to, a collection of information unless it displays a currently valid OMB control number. The OMB control numbers for EPA's regulations in 40 CFR are listed in 40 CFR part 9 and are identified on the form and/or instrument, if applicable.

Burden Statement: The annual public reporting and recordkeeping burden for this collection of information is estimated to average 77 hours per response. Burden means the total time, effort, or financial resources expended by persons to generate, maintain, retain, or disclose or provide information to or for a Federal agency. This includes the time needed to review instructions; develop, acquire, install, and utilize technology and systems for the purposes of collecting, validating, and verifying information, processing and maintaining information, and disclosing and providing information; adjust the existing ways to comply with any previously applicable instructions and requirements which have subsequently changed; train personnel to be able to respond to a collection of information; search data sources; complete and review the collection of information; and transmit or otherwise disclose the information.

Respondents/Affected Entities: Owners or operators of plastic parts and products surface coating operations.

Estimated Number of Respondents: 828.

Frequency of Response: Initially, Semiannually, On Occasion.

Estimated Total Annual Hour Burden: 321,393.

Estimated Total Annual Cost: $ 27,220,752, includes $16,000 capital/startup costs and $248,400 annualized O&M costs.

Changes in the Estimates: There is an increase of 278,860 hours in the total estimated burden currently identified in the OMB Inventory of Approved ICR Burdens. The increase in burden reflects the need for facilities to be in compliance with the rule requirements prior to the date of this ICR, and a revision in the number of facilities subject to the NESHAP. The increase in Operations and Maintenance cost is due to installation and maintenance of equipment used to verify compliance with the rule requirements.

Dated: January 12, 2007.

Oscar Morales,

Director, Collection Strategies Division.