94-1965. Public Meeting on Planned Effluent Guidelines for the Metal Products and Machinery Category  

  • [Federal Register Volume 59, Number 19 (Friday, January 28, 1994)]
    [Unknown Section]
    [Page ]
    From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
    [FR Doc No: 94-1965]
    
    
    [Federal Register: January 28, 1994]
    
    
    -----------------------------------------------------------------------
    
    
    ENVIRONMENTAL PROTECTION AGENCY
    40 CFR Part 438
    
    [FRL-4830-8]
    
    
    Public Meeting on Planned Effluent Guidelines for the Metal 
    Products and Machinery Category
    
    AGENCY: Environmental Protection Agency (EPA).
    
    ACTION: Announcement of public meeting.
    
    -----------------------------------------------------------------------
    
    SUMMARY: The Environmental Protection Agency is announcing a public 
    meeting prior to proposing effluent guidelines and standards for the 
    Metal Products and Machinery category. EPA intends to propose a rule in 
    November 1994, and this is the only public meeting that the Agency 
    plans to sponsor prior to proposal. The meeting is intended to be a 
    forum in which EPA can report on the status of regulatory development 
    and in which interested parties can provide information and ideas to 
    the Agency on key technical, scientific, and other issues.
    DATES: The meeting will be held on February 23, 1994 from 9 a.m. to 5 
    p.m.
    
    ADDRESSES: The meeting will be held at the U.S. Geological Survey 
    (USGS) National Center Auditorium, 12201 Sunrise Valley Drive, Reston, 
    Virginia. Seating will be available for approximately 300 attendees.
        The USGS National Center is located approximately five miles from 
    Dulles International Airport. To reach USGS, take the Dulles Toll Road 
    to Reston Parkway, go south on Reston Parkway to Sunrise Valley Drive, 
    right on Sunrise Valley Drive, 1/4 mile to the USGS entrance on the 
    left side of the road.
    
    FOR FURTHER INFORMATION CONTACT: Bill Cleary, Engineering and Analysis 
    Division, Office of Science and Technology/Office of Water, Mail Code 
    4303, US EPA, 401 M Street, SW., Washington, DC 20460. Telephone (202) 
    260-9817, fax (202) 260-7185.
    
    SUPPLEMENTARY INFORMATION: EPA is developing effluent limitations 
    guidelines and standards for the metal products and machinery category 
    under authority of the Clean Water Act (33 U.S.C. 1251 et seq.). The 
    metal products and machinery (MP&M) category includes facilities that 
    manufacture, rebuild and maintain finished metal parts, products, or 
    machines.
        The public meeting will include discussions of the effluent 
    guidelines regulatory development process, applicability of the 
    forthcoming rule, regulatory approach (i.e. mass-based vs. 
    concentration-based effluent limits), affected population estimates, 
    and general MP&M issues. The meeting will not be recorded by a reporter 
    or transcribed for inclusion in the record for the MP&M industry 
    rulemaking.
        Documents relating to the topics mentioned above and a more 
    detailed agenda will be available at the meeting.
        Dated: January 24, 1994.
    Tudor T. Davies,
    Director, Office of Science and Technology.
    [FR Doc. 94-1965 Filed 1-27-94; 8:45 am]
    BILLING CODE 6560-50-F
    
    
    

Document Information

Published:
01/28/1994
Department:
Environmental Protection Agency
Entry Type:
Uncategorized Document
Action:
Announcement of public meeting.
Document Number:
94-1965
Dates:
The meeting will be held on February 23, 1994 from 9 a.m. to 5 p.m.
Pages:
0-0 (None pages)
Docket Numbers:
Federal Register: January 28, 1994, FRL-4830-8
CFR: (1)
40 CFR 438