[Federal Register Volume 64, Number 203 (Thursday, October 21, 1999)]
[Proposed Rules]
[Pages 56712-56715]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 99-27565]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. 98-NM-248-AD]
RIN 2120-AA64
Airworthiness Directives; Airbus Model A300 B2 and B4 Series
Airplanes
AGENCY: Federal Aviation Administration, DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: This document proposes the adoption of a new airworthiness
directive (AD) that is applicable to certain Airbus Model A300 B2 and
B4 series airplanes. This proposal would require repetitive inspections
to detect cracking of the inner skin panel of the longitudinal lap
joint; and repair, or modification and new repetitive inspections, if
necessary. This proposal is prompted by issuance of mandatory
continuing airworthiness information by a foreign civil airworthiness
authority. The actions specified by the proposed AD are intended to
detect and correct stress corrosion cracking of the inner skin panel of
the longitudinal lap joint, which could result in rapid
depressurization of the airplane.
DATES: Comments must be received by November 22, 1999.
ADDRESSES: Submit comments in triplicate to the Federal Aviation
Administration (FAA), Transport Airplane Directorate, ANM-114,
Attention: Rules Docket No. 98-NM-248-AD, 1601 Lind Avenue, SW.,
Renton, Washington 98055-4056. Comments may be inspected at this
location between 9:00 a.m. and 3:00 p.m., Monday through Friday, except
Federal holidays.
The service information referenced in the proposed rule may be
obtained from Airbus Industrie, 1 Rond Point Maurice Bellonte, 31707
Blagnac Cedex, France. This information may be examined at the FAA,
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton,
Washington.
FOR FURTHER INFORMATION CONTACT: Norman B. Martenson, Manager,
International Branch, ANM-116, FAA, Transport Airplane Directorate,
1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425)
227-2110; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Comments Invited
Interested persons are invited to participate in the making of the
[[Page 56713]]
proposed rule by submitting such written data, views, or arguments as
they may desire. Communications shall identify the Rules Docket number
and be submitted in triplicate to the address specified above. All
communications received on or before the closing date for comments,
specified above, will be considered before taking action on the
proposed rule. The proposals contained in this notice may be changed in
light of the comments received.
Comments are specifically invited on the overall regulatory,
economic, environmental, and energy aspects of the proposed rule. All
comments submitted will be available, both before and after the closing
date for comments, in the Rules Docket for examination by interested
persons. A report summarizing each FAA-public contact concerned with
the substance of this proposal will be filed in the Rules Docket.
Commenters wishing the FAA to acknowledge receipt of their comments
submitted in response to this notice must submit a self-addressed,
stamped postcard on which the following statement is made: ``Comments
to Docket Number 98-NM-248-AD.'' The postcard will be date stamped and
returned to the commenter.
Availability of NPRMs
Any person may obtain a copy of this NPRM by submitting a request
to the FAA, Transport Airplane Directorate, ANM-114, Attention: Rules
Docket No. 98-NM-248-AD, 1601 Lind Avenue, SW., Renton, Washington
98055-4056.
Discussion
The Direction Generale de l' Aviation Civile (DGAC), which is the
airworthiness authority for France, notified the FAA that an unsafe
condition may exist on certain Airbus Model A300 B2 and B4 series
airplanes. The DGAC advises that, on four in-service Airbus Model A300
series airplanes, cracking of the inner skin panel of the longitudinal
lap joint was detected between frames 67 and 70 at stringer 57. The
cracking of the fuselage skin panel was attributed to stress corrosion.
On two of the airplanes, corrosion was found previously in the long lap
joints, and those areas were reworked beyond the limits provided in the
Airbus A300 Structural Repair Manual. Subsequent stress corrosion
cracking is attributed to the improper rework. Such cracking of the
inner skin panel of the longitudinal lap joint, if not corrected, could
result in rapid depressurization of the airplane.
Explanation of Relevant Service Information
The manufacturer has issued Airbus Service Bulletin A300-53-305,
Revision 1, dated January 29, 1999. That service bulletin describes
procedures for repetitive external and internal eddy current
inspections to detect cracking of the inner skin panel of the
longitudinal lap joint between frames 65 and 72 at stringer 57, and
repair, if necessary. For repaired areas, the service bulletin also
specifies new repetitive inspections. The DGAC classified the service
bulletin as mandatory and issued French airworthiness directive 98-150-
246(B), dated April 8, 1998, in order to assure the continued
airworthiness of these airplanes in France.
The manufacturer also has issued Airbus Service Bulletin A300-53-
306, dated September 5, 1995, which describes procedures for
modification of the inner skin panel of the longitudinal lap joint
between frames 65 and 72 at stringer 57 by installation of a doubler.
That modification is intended to delay the onset of cracking of the
inner skin panel of the longitudinal lap joint, and would eliminate the
need to accomplish the repetitive inspections described in Airbus
Service Bulletin A300-53-305, Revision 1, for all modified areas.
The manufacturer also has issued Airbus Service Bulletin A300-53-
211, Revision 5, dated April 29, 1999. That service bulletin describes
inspection criteria to detect cracking of, among other areas, the inner
skin panel of the longitudinal lap joint between frames 65 and 72 at
stringer 57 after it has been modified in accordance with Airbus
Service Bulletin A300-53-306.
FAA's Conclusions
This airplane model is manufactured in France and is type
certificated for operation in the United States under the provisions of
section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and
the applicable bilateral airworthiness agreement. Pursuant to this
bilateral airworthiness agreement, the DGAC has kept the FAA informed
of the situation described above. The FAA has examined the findings of
the DGAC, reviewed all available information, and determined that AD
action is necessary for products of this type design that are
certificated for operation in the United States.
Explanation of Requirements of Proposed Rule
Since an unsafe condition has been identified that is likely to
exist or develop on other airplanes of the same type design registered
in the United States, the proposed AD would require accomplishment of
the actions specified in the service bulletins described previously,
except as discussed below.
Difference Between Proposed Rule and Service Bulletins
Operators should note that, unlike the procedures described in
Airbus Service Bulletin A300-53-305, Revision 1, and Airbus Service
Bulletin A300-53-211, Revision 5, this proposed AD would not permit
further flight if a crack is detected in the inner skin panel of the
longitudinal lap joint. The FAA has determined that, because of the
safety implications and consequences associated with such cracking, any
subject inner skin panel that is found to be cracked must be repaired
or modified prior to further flight.
Difference Between Proposed Rule and Foreign Airworthiness
Directive
Operators should note that, although French airworthiness directive
98-150-246(B) states that no inspections in accordance with that
airworthiness directive are necessary after accomplishment of Airbus
Service Bulletin A300-53-306, this proposed AD would require repetitive
inspections in accordance with Airbus Service Bulletin A300-53-211,
Revision 5, for areas modified in accordance with Airbus Service
Bulletin A300-53-306. The modification described in Airbus Service
Bulletin A300-53-306 is intended to delay the onset of cracking of the
inner skin panel of the longitudinal lap joint. However, cracking may
still occur in the modified area. The FAA finds that repetitive
inspections of the modified area are necessary to ensure that any
cracking is detected in a timely manner.
Other Relevant Rulemaking
On May 28, 1996, the FAA issued AD 96-12-02, Amendment 39-9644 (61
FR 28497, June 5, 1996). The applicability statement of that AD is the
same as for this proposed AD. That AD requires measurements of the
thickness of the inner skin of, and inspections to detect cracking of,
the longitudinal lap joint from the inside of the fuselage at certain
stringers, and repair, if necessary, in accordance with Airbus All
Operator Telex (AOT) 53-05, Revision 1, dated August 16, 1993. Airbus
Service Bulletin A300-53-305, Revision 1, specifies separate compliance
times for airplanes on which Airbus AOT 53-05, Revision 1, has been
accomplished. Because the actions specified in that AOT are already
required by AD 96-12-02, this proposed AD does not specify compliance
times for airplanes on
[[Page 56714]]
which the AOT has not been accomplished.
Cost Impact
The FAA estimates that 3 airplanes of U.S. registry would be
affected by this proposed AD, that it would take approximately 4 work
hours per airplane to accomplish the proposed eddy current inspection
(either internal or external), and that the average labor rate is $60
per work hour. Based on these figures, the cost impact of the proposed
AD on U.S. operators is estimated to be $720, or $240 per airplane, per
inspection cycle.
The cost impact figure discussed above is based on assumptions that
no operator has yet accomplished any of the proposed requirements of
this AD action, and that no operator would accomplish those actions in
the future if this AD were not adopted.
Regulatory Impact
The regulations proposed herein would not have substantial direct
effects on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, in
accordance with Executive Order 12612, it is determined that this
proposal would not have sufficient federalism implications to warrant
the preparation of a Federalism Assessment.
For the reasons discussed above, I certify that this proposed
regulation (1) is not a ``significant regulatory action'' under
Executive Order 12866; (2) is not a ``significant rule'' under the DOT
Regulatory Policies and Procedures (44 FR 11034, February 26, 1979);
and (3) if promulgated, will not have a significant economic impact,
positive or negative, on a substantial number of small entities under
the criteria of the Regulatory Flexibility Act. A copy of the draft
regulatory evaluation prepared for this action is contained in the
Rules Docket. A copy of it may be obtained by contacting the Rules
Docket at the location provided under the caption ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration proposes to amend
part 39 of the Federal Aviation Regulations (14 CFR part 39) as
follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. Section 39.13 is amended by adding the following new
airworthiness directive:
Airbus Industrie: Docket 98-NM-248-AD.
Applicability: Model A300 B2 and B4 series airplanes,
manufacturer serial numbers 003 through 156 inclusive; certificated
in any category.
Note 1: This AD applies to each airplane identified in the
preceding applicability provision, regardless of whether it has been
modified, altered, or repaired in the area subject to the
requirements of this AD. For airplanes that have been modified,
altered, or repaired so that the performance of the requirements of
this AD is affected, the owner/operator must request approval for an
alternative method of compliance in accordance with paragraph (f) of
this AD. The request should include an assessment of the effect of
the modification, alteration, or repair on the unsafe condition
addressed by this AD; and, if the unsafe condition has not been
eliminated, the request should include specific proposed actions to
address it.
Compliance: Required as indicated, unless accomplished
previously.
To detect and correct stress corrosion cracking of the inner
skin panel of the longitudinal lap joint, which could result in
rapid depressurization of the airplane, accomplish the following:
Initial Inspection
(a) Within 400 flight cycles after the effective date of this
AD, perform an external eddy current inspection for cracking of the
inner skin panel of the longitudinal lap joint between frames 65 and
72 at stringer 57, in accordance with Airbus Service Bulletin A300-
53-305, Revision 1, dated January 29, 1999.
Repetitive Inspections
(b) If no cracking is detected during the inspection performed
in accordance with paragraph (a) of this AD: Thereafter, perform an
internal or external eddy current inspection, as specified in
paragraphs (b)(1) and (b)(2) of this AD, as applicable; at intervals
not to exceed 1,250 flight cycles or 7 months, whichever occurs
first; in accordance with Airbus Service Bulletin A300-53-305,
Revision 1, dated January 29, 1999; until the requirements of
paragraph (e) of this AD have been accomplished.
(1) If the most recent inspection was an internal eddy current
inspection, perform an external eddy current inspection of the inner
skin panel of the longitudinal lap joint.
(2) If the most recent inspection was an external eddy current
inspection, perform an internal eddy current inspection of the inner
skin panel of the longitudinal lap joint.
Corrective Actions
(c) If any cracking is detected during any inspection performed
in accordance with paragraph (a) or (b) of this AD, prior to further
flight, accomplish the actions required by either paragraph (c)(1)
or paragraph (c)(2) of this AD.
(1) Repair the inner skin panel of the longitudinal lap joint in
accordance with Airbus Service Bulletin A300-53-305, Revision 1,
dated January 29, 1999. Thereafter, repeat the inspection of areas
in which no cracking is detected at the interval specified in, and
in accordance with, paragraph (b) of this AD; and repeat the
inspection of the repaired area at the intervals specified in the
service bulletin, in accordance with the service bulletin. If any
cracking is found in the repaired area during any repetitive
inspection, prior to further flight, repair in accordance with the
service bulletin.
Note 2: Airbus Service Bulletin A300-53-305, Revision 1, dated
January 29, 1999, references Airbus Structural Repair Manual Chapter
53-17-00, as an additional source of service information to
accomplish the repair specified in paragraph (c)(1) of this AD.
(2) Modify the inner skin panel of the longitudinal lap joint in
accordance with Airbus Service Bulletin A300-53-306, dated September
5, 1995, and accomplish the requirements of paragraph (d) of this
AD.
(d) For airplanes modified in accordance with Airbus Service
Bulletin A300-53-306, dated September 5, 1995: Inspect the modified
inner skin panel of the longitudinal lap joint to detect cracking at
the applicable threshold and repetitive intervals specified in Table
1A, 1B, or 2 of Airbus Service Bulletin A300-53-211, Revision 5,
dated April 29, 1999, in accordance with Airbus Service Bulletin
A300-53-211, Revision 5. If any cracking is found during any
repetitive inspection, prior to further flight, repair in accordance
with Airbus Service Bulletin A300-53-211, Revision 5.
Optional Modification
(e) Modification of the inner skin panel of the longitudinal lap
joint in accordance with Airbus Service Bulletin A300-53-306, dated
September 5, 1995, constitutes terminating action for the repetitive
inspections required by paragraph (b) of this AD. Such modification
does not terminate the repetitive inspections required by paragraph
(d) of this AD.
Alternative Method of Compliance
(f) An alternative method of compliance or adjustment of the
compliance time that provides an acceptable level of safety may be
used if approved by the Manager, International Branch, ANM-116.
Operators shall submit their requests through an appropriate FAA
Principal Maintenance Inspector, who may add comments and then send
it to the Manager, International Branch, ANM-116.
Note 3: Information concerning the existence of approved
alternative methods of compliance with this AD, if any, may be obtained
from the International Branch, ANM-116.
[[Page 56715]]
Special Flight Permits
(g) Special flight permits may be issued in accordance with
sections 21.197 and 21.199 of the Federal Aviation Regulations (14
CFR 21.197 and 21.199) to operate the airplane to a location where
the requirements of this AD can be accomplished.
Note 4: The subject of this AD is addressed in French
airworthiness directive 98-150-246(B), dated April 8, 1998.
Issued in Renton, Washington, on October 15, 1999.
D.L. Riggin,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 99-27565 Filed 10-20-99; 8:45 am]
BILLING CODE 4910-13-P
