[Federal Register Volume 63, Number 207 (Tuesday, October 27, 1998)]
[Proposed Rules]
[Pages 57260-57262]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 98-28668]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. 98-NM-244-AD]
RIN 2120-AA64
Airworthiness Directives; Saab Model SAAB SF340A and SAAB 340B
Series Airplanes
AGENCY: Federal Aviation Administration, DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: This document proposes the adoption of a new airworthiness
directive (AD) that is applicable to certain Saab Model SAAB SF340A and
SAAB 340B series airplanes. This proposal would require removing the
control quadrant, securing the power lever cam screws with Loctite, and
reinstalling the control quadrant. This proposal is prompted by
issuance of mandatory continuing airworthiness information by a foreign
civil airworthiness authority. The actions specified by the proposed AD
are intended to prevent the cam screws of the engine power levers from
backing out and interfering with the movement of the engine power
levers, which could result in limited engine power, and consequent
reduced controllability of the airplane.
DATES: Comments must be received by November 27, 1998.
ADDRESSES: Submit comments in triplicate to the Federal Aviation
Administration (FAA), Transport Airplane Directorate, ANM-114,
Attention: Rules Docket No. 98-NM-244-AD, 1601 Lind Avenue, SW.,
Renton, Washington 98055-4056. Comments may be inspected at this
location between 9:00 a.m. and 3:00 p.m., Monday through Friday, except
Federal holidays.
The service information referenced in the proposed rule may be
obtained from Saab Aircraft AB, SAAB Aircraft Product Support, S-
581.88, Linkoping, Sweden. This information may be examined at the FAA,
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton,
Washington.
FOR FURTHER INFORMATION CONTACT: Norman B. Martenson, Manager,
International Branch, ANM-116, FAA, Transport Airplane Directorate,
1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425)
227-2110; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Comments Invited
Interested persons are invited to participate in the making of the
proposed rule by submitting such written data, views, or arguments as
they may desire. Communications shall identify the Rules Docket number
and be submitted in triplicate to the address specified above. All
communications received on or before the closing date for comments,
specified above, will be considered before taking action on the
proposed rule. The proposals contained in this notice may be changed in
light of the comments received.
Comments are specifically invited on the overall regulatory,
economic, environmental, and energy aspects of the proposed rule. All
comments submitted will be available, both before and after the closing
date for comments, in the Rules Docket for examination by interested
persons. A report summarizing each FAA-public contact concerned with
the substance of this proposal will be filed in the Rules Docket.
Commenters wishing the FAA to acknowledge receipt of their comments
[[Page 57261]]
submitted in response to this notice must submit a self-addressed,
stamped postcard on which the following statement is made: ``Comments
to Docket Number 98-NM-244-AD.'' The postcard will be date stamped and
returned to the commenter.
Availability of NPRMs
Any person may obtain a copy of this NPRM by submitting a request
to the FAA, Transport Airplane Directorate, ANM-114, Attention: Rules
Docket No. 98-NM-244-AD, 1601 Lind Avenue, SW., Renton, Washington
98055-4056.
Discussion
The Luftfartsverket (LFV), which is the airworthiness authority for
Sweden, notified the FAA that an unsafe condition may exist on certain
Saab Model SAAB SF340A and SAAB 340B series airplanes. The LFV advises
that it has received reports of the engine power levers binding.
Investigation revealed that, during a previous modification of the
control quadrant, the incorrect screws were used to install the spacer
between the two power lever cams in the flight idle stop unit.
Incorrect screws may also have been used during modification of the
control quadrant on other airplanes. Consequently, the cams screws were
not properly secured, which allowed the screws to back out and
interfere with the movement of the engine power levers. Such
interference, if not corrected, could result in limited engine power,
and consequent reduced controllability of the airplane.
Explanation of Relevant Service Information
SAAB has issued Service Bulletin 340-76-042, dated May 28, 1998,
including Attachments 1, 2, and 3, dated May 1, 1998, which describes
procedures for removing the control quadrant, securing the power lever
cam screws with Loctite, and reinstalling the control quadrant.
Accomplishment of the actions specified in the service bulletin is
intended to adequately address the identified unsafe condition. The LFV
classified this service bulletin as mandatory and issued Swedish
airworthiness directive 1-128, dated May 29, 1998, in order to assure
the continued airworthiness of these airplanes in Sweden.
FAA's Conclusions
These airplane models are manufactured in Sweden and are type
certificated for operation in the United States under the provisions of
section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and
the applicable bilateral airworthiness agreement. Pursuant to this
bilateral airworthiness agreement, the LFV has kept the FAA informed of
the situation described above. The FAA has examined the findings of the
LFV, reviewed all available information, and determined that AD action
is necessary for products of this type design that are certificated for
operation in the United States.
Explanation of Requirements of Proposed Rule
Since an unsafe condition has been identified that is likely to
exist or develop on other airplanes of the same type design registered
in the United States, the proposed AD would require accomplishment of
the actions specified in the service bulletin described previously.
Cost Impact
The FAA estimates that 283 airplanes of U.S. registry would be
affected by this proposed AD, that it would take approximately 9 work
hours per airplane to accomplish the proposed actions, and that the
average labor rate is $60 per work hour. Required parts would be
supplied by the manufacturer at no cost to the operators. Based on
these figures, the cost impact of the proposed AD on U.S. operators is
estimated to be $152,820, or $540 per airplane.
The cost impact figure discussed above is based on assumptions that
no operator has yet accomplished any of the proposed requirements of
this AD action, and that no operator would accomplish those actions in
the future if this AD were not adopted.
Regulatory Impact
The regulations proposed herein would not have substantial direct
effects on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, in
accordance with Executive Order 12612, it is determined that this
proposal would not have sufficient federalism implications to warrant
the preparation of a Federalism Assessment.
For the reasons discussed above, I certify that this proposed
regulation (1) is not a ``significant regulatory action'' under
Executive Order 12866; (2) is not a ``significant rule'' under the DOT
Regulatory Policies and Procedures (44 FR 11034, February 26, 1979);
and (3) if promulgated, will not have a significant economic impact,
positive or negative, on a substantial number of small entities under
the criteria of the Regulatory Flexibility Act. A copy of the draft
regulatory evaluation prepared for this action is contained in the
Rules Docket. A copy of it may be obtained by contacting the Rules
Docket at the location provided under the caption ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration proposes to amend
part 39 of the Federal Aviation Regulations (14 CFR part 39) as
follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. Section 39.13 is amended by adding the following new
airworthiness directive:
SAAB Aircraft AB: Docket 98-NM-244-AD.
Applicability: Model SAAB SF340A and SAAB 340B series airplanes,
as listed in Saab Service Bulletin 340-76-042, dated May 28, 1998,
certificated in any category.
Note 1: This AD applies to each airplane identified in the
preceding applicability provision, regardless of whether it has been
otherwise modified, altered, or repaired in the area subject to the
requirements of this AD. For airplanes that have been modified,
altered, or repaired so that the performance of the requirements of
this AD is affected, the owner/operator must request approval for an
alternative method of compliance in accordance with paragraph (c) of
this AD. The request should include an assessment of the effect of
the modification, alteration, or repair on the unsafe condition
addressed by this AD; and, if the unsafe condition has not been
eliminated, the request should include specific proposed actions to
address it.
Compliance: Required as indicated, unless accomplished
previously.
To prevent the cam screws of the engine power levers from
backing out and interfering with the movement of the engine power
levers, which could result in limited engine power, and consequent
reduced controllability of the airplane, accomplish the following:
(a) Within 1,200 flight hours or 6 months after the effective
date of this AD, whichever occurs first, remove the control
quadrant, secure the power lever cam screws with Loctite, and
reinstall the control quadrant, in accordance with Saab Service
Bulletin 340-76-042, dated May 28, 1998, including Attachments 1, 2,
and 3, all dated May 1, 1998.
(b) As of the effective date of this AD, no person shall install
on any airplane any control quandrant unit having part number
[[Page 57262]]
(P/N) 53082, 53162, or 53170, unless the control quandrant unit has
been modified in accordance with this AD.
(c) An alternative method of compliance or adjustment of the
compliance time that provides an acceptable level of safety may be
used if approved by the Manager, International Branch, ANM-116, FAA,
Transport Airplane Directorate. Operators shall submit their
requests through an appropriate FAA Principal Maintenance Inspector,
who may add comments and then send it to the Manager, International
Branch, ANM-116.
Note 2: Information concerning the existence of approved
alternative methods of compliance with this AD, if any, may be
obtained from the International Branch, ANM-116.
(d) Special flight permits may be issued in accordance with
sections 21.197 and 21.199 of the Federal Aviation Regulations (14
CFR 21.197 and 21.199) to operate the airplane to a location where
the requirements of this AD can be accomplished.
Note 3: The subject of this AD is addressed in Swedish
airworthiness directive 1-128, dated May 29, 1998.
Issued in Renton, Washington, on October 21, 1998.
Darrell M. Pederson,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 98-28668 Filed 10-26-98; 8:45 am]
BILLING CODE 4910-13-U
