97-29822. Airworthiness Directives; Boeing Model 757-200 Series Airplanes  

  • [Federal Register Volume 62, Number 219 (Thursday, November 13, 1997)]
    [Proposed Rules]
    [Pages 60807-60808]
    From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
    [FR Doc No: 97-29822]
    
    
    =======================================================================
    -----------------------------------------------------------------------
    
    DEPARTMENT OF TRANSPORTATION
    
    Federal Aviation Administration
    
    14 CFR Part 39
    
    [Docket No. 96-NM-232-AD]
    RIN 2120-AA64
    
    
    Airworthiness Directives; Boeing Model 757-200 Series Airplanes
    
    AGENCY: Federal Aviation Administration, DOT.
    
    ACTION: Notice of proposed rulemaking (NPRM).
    
    -----------------------------------------------------------------------
    
    SUMMARY: This document proposes the adoption of a new airworthiness 
    directive (AD) that is applicable to certain Boeing Model 757-200 
    series airplanes. This proposal would require modification of certain 
    passenger doors. This proposal is prompted by reports that certain 
    passenger doors could not be opened due to the escape slide shelf 
    assembly and escape slide falling onto the girt bar lifting mechanism 
    of the door. The actions specified by the proposed AD are intended to 
    prevent the escape slide shelf assembly and escape slide from falling 
    on the girt bar of a passenger door due to failed rivets of the escape 
    slide shelf assembly, and consequent inability to open the passenger 
    door and to use the escape slide at that door during an emergency 
    evacuation of the airplane.
    
    DATES: Comments must be received by December 29, 1997.
    
    ADDRESSES: Submit comments in triplicate to the Federal Aviation 
    Administration (FAA), Transport Airplane Directorate, ANM-103, 
    Attention: Rules Docket No. 96-NM-232-AD, 1601 Lind Avenue, SW., 
    Renton, Washington 98055-4056. Comments may be inspected at this 
    location between 9:00 a.m. and 3:00 p.m., Monday through Friday, except 
    Federal holidays.
        The service information referenced in the proposed rule may be 
    obtained from Boeing Commercial Airplane Group, P.O. Box 3707, Seattle, 
    Washington 98124-2207. This information may be examined at the FAA, 
    Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, 
    Washington.
    
    FOR FURTHER INFORMATION CONTACT: Keith Ladderud, Aerospace Engineer, 
    Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office, 
    1601 Lind Avenue, SW., Renton, Washington; telephone (425) 227-2780; 
    fax (425) 227-1181.
    
    SUPPLEMENTARY INFORMATION:
    
    Comments Invited
    
        Interested persons are invited to participate in the making of the 
    proposed rule by submitting such written data, views, or arguments as 
    they may desire. Communications shall identify the Rules Docket number 
    and be submitted in triplicate to the address specified above. All 
    communications received on or before the closing date for comments, 
    specified above, will be considered before taking action on the 
    proposed rule. The proposals contained in this notice may be changed in 
    light of the comments received.
        Comments are specifically invited on the overall regulatory, 
    economic, environmental, and energy aspects of the proposed rule. All 
    comments submitted will be available, both before and after the closing 
    date for comments, in the Rules Docket for examination by interested 
    persons. A report summarizing each FAA-public contact concerned with 
    the substance of this proposal will be filed in the Rules Docket.
        Commenters wishing the FAA to acknowledge receipt of their comments 
    submitted in response to this notice must submit a self-addressed, 
    stamped postcard on which the following statement is made: ``Comments 
    to Docket Number 96-NM-232-AD.'' The postcard will be date stamped and 
    returned to the commenter.
    
    Availability of NPRMs
    
        Any person may obtain a copy of this NPRM by submitting a request 
    to the FAA, Transport Airplane Directorate, ANM-103, Attention: Rules 
    Docket No. 96-NM-232-AD, 1601 Lind Avenue, SW., Renton, Washington 
    98055-4056.
    
    Discussion
    
        The FAA has received reports indicating that various passenger 
    doors (Number 1, 2, or 4) could not be opened. Investigation revealed 
    that the escape slide shelf assembly and escape slide had fallen onto 
    the girt bar lifting mechanism of the passenger door due to failure of 
    four rivets of the shelf assembly. Such failure, if not corrected, 
    could result in inability to open the Number 1, 2, or 4 passenger door, 
    and consequent inability to use the escape slide at the door during an 
    emergency evacuation of the airplane.
    
    Explanation of Relevant Service Information
    
        The FAA has reviewed and approved Boeing Service Bulletin 757-25-
    0175, dated May 30, 1996, and Revision 1, dated March 6, 1997, which 
    describes procedures for modifying the escape slide shelf assemblies of 
    the Number 1, 2, and 4 passenger doors. The modification entails 
    replacing the four existing rivets of the escape slide shelf assembly 
    of the passenger doors with steel rivets. The modification will ensure 
    that the escape slide shelf assembly and escape slide do not fall onto 
    the girt bar lifting mechanism.
    
    Explanation of Requirements of Proposed Rule
    
        Since an unsafe condition has been identified that is likely to 
    exist or develop on other products of this same type design, the 
    proposed AD would require modification of the escape slide shelf 
    assemblies of the Numbers 1, 2,
    
    [[Page 60808]]
    
    and 4 passenger doors. The actions would be required to be accomplished 
    in accordance with the service bulletin described previously.
    
    Cost Impact
    
        There are approximately 673 Boeing Model 757-200 series airplanes 
    of the affected design in the worldwide fleet. The FAA estimates that 
    381 airplanes of U.S. registry would be affected by this proposed AD, 
    that it would take approximately 6 work hours per airplane to 
    accomplish the proposed actions, and that the average labor rate is $60 
    per work hour. Required parts would cost approximately $234 per 
    airplane. Based on these figures, the cost impact of the proposed AD on 
    U.S. operators is estimated to be $226,314, or $594 per airplane.
        The cost impact figure discussed above is based on assumptions that 
    no operator has yet accomplished any of the proposed requirements of 
    this AD action, and that no operator would accomplish those actions in 
    the future if this AD were not adopted.
    
    Regulatory Impact
    
        The regulations proposed herein would not have substantial direct 
    effects on the States, on the relationship between the national 
    government and the States, or on the distribution of power and 
    responsibilities among the various levels of government. Therefore, in 
    accordance with Executive Order 12612, it is determined that this 
    proposal would not have sufficient federalism implications to warrant 
    the preparation of a Federalism Assessment.
        For the reasons discussed above, I certify that this proposed 
    regulation (1) is not a ``significant regulatory action'' under 
    Executive Order 12866; (2) is not a ``significant rule'' under the DOT 
    Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); 
    and (3) if promulgated, will not have a significant economic impact, 
    positive or negative, on a substantial number of small entities under 
    the criteria of the Regulatory Flexibility Act. A copy of the draft 
    regulatory evaluation prepared for this action is contained in the 
    Rules Docket. A copy of it may be obtained by contacting the Rules 
    Docket at the location provided under the caption ADDRESSES.
    
    List of Subjects in 14 CFR Part 39
    
        Air transportation, Aircraft, Aviation safety, Safety.
    
    The Proposed Amendment
    
        Accordingly, pursuant to the authority delegated to me by the 
    Administrator, the Federal Aviation Administration proposes to amend 
    part 39 of the Federal Aviation Regulations (14 CFR part 39) as 
    follows:
    
    PART 39--AIRWORTHINESS DIRECTIVES
    
        1. The authority citation for part 39 continues to read as follows:
    
        Authority: 49 U.S.C. 106(g), 40113, 44701.
    
    
    Sec. 39.13  [Amended]
    
        2. Section 39.13 is amended by adding the following new 
    airworthiness directive:
    
    Boeing: Docket 96-NM-232-AD.
    
        Applicability: Model 757-200 series airplanes, as listed in 
    Boeing Service Bulletin 757-25-0175, Revision 1, dated March 6, 
    1997, certificated in any category.
    
        Note 1: This AD applies to each airplane identified in the 
    preceding applicability provision, regardless of whether it has been 
    otherwise modified, altered, or repaired in the area subject to the 
    requirements of this AD. For airplanes that have been modified, 
    altered, or repaired so that the performance of the requirements of 
    this AD is affected, the owner/operator must request approval for an 
    alternative method of compliance in accordance with paragraph (c) of 
    this AD. The request should include an assessment of the effect of 
    the modification, alteration, or repair on the unsafe condition 
    addressed by this AD; and, if the unsafe condition has not been 
    eliminated, the request should include specific proposed actions to 
    address it.
    
        Compliance: Required as indicated, unless accomplished 
    previously.
        To prevent inability to open the Number 1, 2, or 4 passenger 
    door and to use the escape slide at that door during an emergency 
    evacuation of the airplane, accomplish the following:
        (a) Within 18 months after the effective date of this AD, modify 
    the escape slide shelf assemblies of the Numbers 1, 2, and 4 
    passenger doors in accordance with Boeing Service Bulletin 757-25-
    0175, dated May 30, 1996, or Revision 1, dated March 6, 1997.
        (b) As of the effective date of this AD, no person shall install 
    an escape slide shelf assembly having part number 416N2400-6 or 
    416N2400-7 on any airplane.
        (c) An alternative method of compliance or adjustment of the 
    compliance time that provides an acceptable level of safety may be 
    used if approved by the Manager, Seattle Aircraft Certification 
    Office (ACO), FAA, Transport Airplane Directorate. Operators shall 
    submit their requests through an appropriate FAA Principal 
    Maintenance Inspector, who may add comments and then send it to the 
    Manager, Seattle ACO.
    
        Note 2: Information concerning the existence of approved 
    alternative methods of compliance with this AD, if any, may be 
    obtained from the Seattle ACO.
    
        (d) Special flight permits may be issued in accordance with 
    sections 21.197 and 21.199 of the Federal Aviation Regulations (14 
    CFR 21.197 and 21.199) to operate the airplane to a location where 
    the requirements of this AD can be accomplished.
    
        Issued in Renton, Washington, on November 6, 1997.
    Darrell M. Pederson,
    Acting Manager, Transport Airplane Directorate, Aircraft Certification 
    Service.
    [FR Doc. 97-29822 Filed 11-12-97; 8:45 am]
    BILLING CODE 4910-13-U
    
    
    

Document Information

Published:
11/13/1997
Department:
Federal Aviation Administration
Entry Type:
Proposed Rule
Action:
Notice of proposed rulemaking (NPRM).
Document Number:
97-29822
Dates:
Comments must be received by December 29, 1997.
Pages:
60807-60808 (2 pages)
Docket Numbers:
Docket No. 96-NM-232-AD
RINs:
2120-AA64: Airworthiness Directives
RIN Links:
https://www.federalregister.gov/regulations/2120-AA64/airworthiness-directives
PDF File:
97-29822.pdf
CFR: (1)
14 CFR 39.13