2020-26764. Airworthiness Directives; Airbus Canada Limited Partnership (Type Certificate Previously Held by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.) Airplanes  

  • Start Preamble

    AGENCY:

    Federal Aviation Administration (FAA), DOT.

    ACTION:

    Notice of proposed rulemaking (NPRM).

    SUMMARY:

    The FAA proposes to supersede Airworthiness Directive (AD) 2019-23-15, which applies to certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500-1A11 airplanes. AD 2019-23-15 requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. Since the FAA issued AD 2019-23-15, the FAA has determined that new or more restrictive airworthiness limitations are necessary. This proposed AD would require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. The FAA is proposing this AD to Start Printed Page 78806address the unsafe condition on these products.

    DATES:

    The FAA must receive comments on this proposed AD by January 21, 2021.

    ADDRESSES:

    You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods:

    • Federal eRulemaking Portal: Go to https://www.regulations.gov. Follow the instructions for submitting comments.
    • Fax: 202-493-2251.
    • Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.
    • Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

    For service information identified in this NPRM, contact Airbus Canada Limited Partnership, 13100 Henri-Fabre Boulevard, Mirabel, Québec, J7N 3C6, Canada; telephone 450-476-7676; email a220_crc@abc.airbus; internet http://a220world.airbus.com. You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195.

    Examining the AD Docket

    You may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-1110; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, any comments received, and other information. The street address for Docket Operations is listed above. Comments will be available in the AD docket shortly after receipt.

    Start Further Info

    FOR FURTHER INFORMATION CONTACT:

    Andrea Jimenez, Aerospace Engineer, Airframe and Propulsion Section, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone: 516-228-7330; fax: 516-794-5531; email: 9-avs-nyaco-cos@faa.gov.

    End Further Info End Preamble Start Supplemental Information

    SUPPLEMENTARY INFORMATION:

    Comments Invited

    The FAA invites you to send any written relevant data, views, or arguments about this proposal. Send your comments to an address listed under the ADDRESSES section. Include “Docket No. FAA-2020-1110; Project Identifier MCAI-2020-01003-T” at the beginning of your comments. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. The FAA will consider all comments received by the closing date and may amend the proposal because of those comments.

    Except for Confidential Business Information (CBI) as described in the following paragraph, and other information as described in 14 CFR 11.35, the FAA will post all comments received, without change, to https://www.regulations.gov,, including any personal information you provide. The agency will also post a report summarizing each substantive verbal contact received about this proposed AD.

    Confidential Business Information

    CBI is commercial or financial information that is both customarily and actually treated as private by its owner. Under the Freedom of Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public disclosure. If your comments responsive to this NPRM contain commercial or financial information that is customarily treated as private, that you actually treat as private, and that is relevant or responsive to this NPRM, it is important that you clearly designate the submitted comments as CBI. Please mark each page of your submission containing CBI as “PROPIN.” The FAA will treat such marked submissions as confidential under the FOIA, and they will not be placed in the public docket of this NPRM. Submissions containing CBI should be sent to Andrea Jimenez, Aerospace Engineer, Airframe and Propulsion Section, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone: 516-228-7330; fax: 516-794-5531; email: 9-avs-nyaco-cos@faa.gov. Any commentary that the FAA receives which is not specifically designated as CBI will be placed in the public docket for this rulemaking.

    Discussion

    The FAA issued AD 2019-23-15, Amendment 39-19809 (84 FR 67830, December 12, 2019) (AD 2019-23-15), for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500-1A11 airplanes. AD 2019-23-15 requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. AD 2019-23-15 resulted from a determination that new or more restrictive airworthiness limitations are necessary. The FAA issued AD 2019-23-15 to address reduced structural integrity of the airplane or reduced controllability of the airplane.

    Actions Since AD 2019-23-15 Was Issued

    Since the FAA issued AD 2019-23-15, the FAA has determined that new or more restrictive airworthiness limitations are necessary.

    Transport Canada Civil Aviation (TCCA), which is the aviation authority for Canada, has issued Canadian AD CF-2020-25, dated July 16, 2020 (also referred to after this as the Mandatory Continuing Airworthiness Information, or the MCAI), to correct an unsafe condition for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500-1A11 airplanes. You may examine the MCAI in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-1110.

    This proposed AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. The FAA is proposing this AD to address reduced structural integrity of the airplane or reduced controllability of the airplane. See the MCAI for additional background information.

    Related Service Information Under 1 CFR Part 51

    Airbus Canada Limited Partnership has issued A220 Airworthiness Limitations BD500-3AB48-11400-02, Issue 011.00, dated June 18, 2020. This service information describes airworthiness limitations for fuel tank systems, safe life limits, and certification maintenance requirements. This service information is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section.

    FAA's Determination

    This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to the FAA's bilateral agreement with the State of Design Authority, the FAA has been notified of the unsafe condition described in the MCAI and service information referenced above. The FAA is proposing this AD because the FAA evaluated all the relevant information and determined the unsafe condition described previously is likely to exist or develop on other products of the same type design.Start Printed Page 78807

    Proposed Requirements of This NPRM

    This proposed AD would retain none of the requirements of AD 2019-23-15. This proposed AD would require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations.

    This proposed AD would require revisions to certain operator maintenance documents to include new actions (e.g., inspections) and Critical Design Configuration Control Limitations (CDCCLs). Compliance with these actions and CDCCLs is required by 14 CFR 91.403(c). For airplanes that have been previously modified, altered, or repaired in the areas addressed by this proposed AD, the operator may not be able to accomplish the actions described in the revisions. In this situation, to comply with 14 CFR 91.403(c), the operator must request approval for an alternative method of compliance according to paragraph (i)(1) of this proposed AD.

    Costs of Compliance

    The FAA estimates that this proposed AD affects 11 airplanes of U.S. registry. The FAA estimates the following costs to comply with this proposed AD:

    The FAA has determined that revising the maintenance or inspection program takes an average of 90 work-hours per operator, although the agency recognizes that this number may vary from operator to operator. Since operators incorporate maintenance or inspection program changes for their affected fleet(s), the FAA has determined that a per-operator estimate is more accurate than a per-airplane estimate. Therefore, the agency estimates the average total cost per operator to be $7,650 (90 work-hours × $85 per work-hour).

    Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority.

    The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

    Regulatory Findings

    The FAA determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

    For the reasons discussed above, I certify this proposed regulation:

    (1) Is not a “significant regulatory action” under Executive Order 12866,

    (2) Will not affect intrastate aviation in Alaska, and

    (3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

    Start List of Subjects

    List of Subjects in 14 CFR Part 39

    • Air transportation
    • Aircraft
    • Aviation safety
    • Incorporation by reference
    • Safety
    End List of Subjects

    The Proposed Amendment

    Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

    Start Part

    PART 39—AIRWORTHINESS DIRECTIVES

    End Part Start Amendment Part

    1. The authority citation for part 39 continues to read as follows:

    End Amendment Part Start Authority

    Authority: 49 U.S.C. 106(g), 40113, 44701.

    End Authority
    [Amended]
    Start Amendment Part

    2. The FAA amends § 39.13 by:

    End Amendment Part Start Amendment Part

    a. Removing Airworthiness Directive (AD) 2019-23-15, Amendment 39-19809 ( 84 FR 67830, December 12, 2019), and

    End Amendment Part Start Amendment Part

    b. Adding the following new AD:

    End Amendment Part

    Airbus Canada Limited Partnership (Type Certificate Previously Held by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.): Docket No. FAA-2020-1110; Project Identifier MCAI-2020-01003-T.

    (a) Comments Due Date

    The FAA must receive comments by January 21, 2021.

    (b) Affected ADs

    This AD replaces AD 2019-23-15, Amendment 39-19809 (84 FR 67830, December 12, 2019).

    (c) Applicability

    This AD applies to the Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500-1A11 airplanes, certificated in any category, identified in paragraphs (c)(1) and (2) of this AD.

    (1) Model BD-500-1A10 airplanes, serial numbers 50001 and subsequent with an original airworthiness certificate or original export certificate of airworthiness issued on or before June 18, 2020.

    (2) Model BD-500-1A11 airplanes, serial numbers 55001 and subsequent with an original airworthiness certificate or original export certificate of airworthiness issued on or before June 18, 2020.

    (d) Subject

    Air Transport Association (ATA) of America Code 05, Time Limits/Maintenance Checks.

    (e) Reason

    This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. The FAA is issuing this AD to address reduced structural integrity of the airplane or reduced controllability of the airplane.

    (f) Compliance

    Comply with this AD within the compliance times specified, unless already done.

    (g) New Maintenance or Inspection Program Revision

    Within 90 days after the effective date of this AD, revise the existing maintenance or inspection program, as applicable, to incorporate the information specified in Airbus Canada Limited Partnership A220 Airworthiness Limitations, BD500-3AB48-11400-02, Issue 011.00, dated June 18, 2020. The initial compliance time for doing the tasks is at the time specified in Airbus Canada Limited Partnership A220 Airworthiness Limitations, BD500-3AB48-11400-02, Issue 011.00, dated June 18, 2020, or within 90 days after the effective date of this AD, whichever occurs later.

    (h) New No Alternative Actions, Intervals, or Critical Design Configuration Control Limitations (CDCCLs)

    After the existing maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions (e.g., inspections), intervals, or CDCCLs may be used unless the actions, intervals, and CDCCLs are approved as an alternative method of compliance (AMOC) in accordance with the procedures specified in paragraph (i)(1) of this AD.

    (i) Other FAA AD Provisions

    The following provisions also apply to this AD:

    (1) Alternative Methods of Compliance (AMOCs): The Manager, New York ACO Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the certification office, send it to ATTN: Program Manager, Continuing Operational Safety, FAA, New Start Printed Page 78808York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.

    (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, New York ACO Branch, FAA; or Transport Canada Civil Aviation (TCCA); or Airbus Canada Limited Partnership's TCCA Design Approval Organization (DAO). If approved by the DAO, the approval must include the DAO-authorized signature.

    (j) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) Canadian AD CF-2020-25, dated July 16, 2020, for related information. This MCAI may be found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-1110.

    (2) For more information about this AD, contact Andrea Jimenez, Aerospace Engineer, Airframe and Propulsion Section, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone: 516-228-7330; fax: 516-794-5531; email: 9-avs-nyaco-cos@faa.gov.

    (3) For service information identified in this AD, contact Airbus Canada Limited Partnership, 13100 Henri-Fabre Boulevard, Mirabel, Québec, J7N 3C6, Canada; telephone 450-476-7676; email a220_crc@abc.airbus; internet http://a220world.airbus.com. You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195.

    Start Signature

    Issued on December 1, 2020.

    Gaetano A. Sciortino,

    Deputy Director for Strategic Initiatives, Compliance & Airworthiness Division, Aircraft Certification Service.

    End Signature End Supplemental Information

    [FR Doc. 2020-26764 Filed 12-4-20; 8:45 am]

    BILLING CODE 4910-13-P

Document Information

Published:
12/07/2020
Department:
Federal Aviation Administration
Entry Type:
Proposed Rule
Action:
Notice of proposed rulemaking (NPRM).
Document Number:
2020-26764
Dates:
The FAA must receive comments on this proposed AD by January 21, 2021.
Pages:
78805-78808 (4 pages)
Docket Numbers:
Docket No. FAA-2020-1110, Project Identifier MCAI-2020-01003-T
RINs:
2120-AA64: Airworthiness Directives
RIN Links:
https://www.federalregister.gov/regulations/2120-AA64/airworthiness-directives
Topics:
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety
PDF File:
2020-26764.Pdf
Supporting Documents:
» Airworthiness Directives: Airbus Canada Limited Partnership (Type Certificate Previously Held by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.) Airplanes
» Supporting AD Document
» Airworthiness Directives: Airbus Canada Limited Partnership (Type Certificate Previously Held by C Series Aircraft Limited Partnership (CSALP); Bombardier, Inc.) Airplanes
CFR: (1)
14 CFR 39.13