2023-26884. Stainless Steel Sheet and Strip in Coils From Japan, the Republic of Korea, and Taiwan: Continuation of Antidumping Duty Orders and Countervailing Duty Order

AGENCY:

Enforcement and Compliance, International Trade Administration, Department of Commerce.

SUMMARY:

As a result of the determinations by the U.S. Department of Commerce (Commerce) and the U.S. International Trade Commission (ITC) that revocation of the antidumping duty (AD) orders on stainless steel sheet and strip in coils (SSSSC) from Japan, the Republic of Korea (Korea), and Taiwan and the countervailing duty (CVD) order on SSSSC from Korea would likely lead to the continuation or recurrence of dumping, countervailable subsidies, and material injury to an industry in the United States, Commerce is publishing a notice of continuation of these AD and CVD orders.

DATES:

Applicable October 24, 2023.

FOR FURTHER INFORMATION CONTACT:

Andrew Hart, AD/CVD Operations, Office II, Enforcement and Compliance, International Trade Administration, U.S. Department of Commerce, 1401 Constitution Avenue NW, Washington, DC 20230; telephone: [phone].

SUPPLEMENTARY INFORMATION:

Background

On July 27, 1999, Commerce published in the Federal Register the AD orders on SSSSC from Japan, Korea, and Taiwan, and, on August 6, 1999, Commerce published the CVD order on SSSSC from Korea.^[1] On September 1, 2022, the ITC instituted,^[2] and Commerce initiated,^[3] the fourth sunset review of the Orders, pursuant to section 751(c) of the Tariff Act of 1930, as amended (the Act). As a result of its reviews, Commerce determined that revocation of the Orders would likely lead to the continuation or recurrence of dumping and countervailable subsidies and, therefore, notified the ITC of the magnitude of the margins of dumping and subsidy rates likely to prevail should the Orders be revoked.^[4]

On October 24, 2023, the ITC published its determination, pursuant to sections 751(c) and 752(a) of the Act, that revocation of the Orders would likely lead to continuation or recurrence of material injury to an industry in the United States within a reasonably foreseeable time.^[5]

Scope of the Orders

The merchandise under review is certain stainless steel sheet and strip in coils. Stainless steel is an alloy steel containing, by weight, 1.2 percent or less of carbon and 10.5 percent or more of chromium, with or without other elements. The subject sheet and strip is a flat-rolled product in coils that is greater than 9.5 mm in width and less than 4.75 mm in thickness, and that is annealed or otherwise heat treated and pickled or otherwise descaled. The subject sheet and strip may also be further processed ( e.g., cold-rolled, polished, aluminized, coated, etc.) provided that it maintains the specific dimensions of sheet and strip following such processing.

The merchandise subject to this review is classified in the Harmonized Tariff Schedule of the United States (HTSUS) at subheadings: 7219.13.00.31, 7219.13.00.51, 7219.13.00.71, 7219.13.00.81, 7219.14.00.30, 7219.14.00.65, 7219.14.00.90, 7219.32.00.05, 7219.32.00.20, 7219.32.00.25, 7219.32.00.35, 7219.32.00.36, 7219.32.00.38, 7219.32.00.42, 7219.32.00.44, 7219.33.00.05, 7219.33.00.20, 7219.33.00.25, 7219.33.00.35, 7219.33.00.36, 7219.33.00.38, 7219.33.00.42, 7219.33.00.44, 7219.34.00.05, 7219.34.00.20, 7219.34.00.25, 7219.34.00.30, 7219.34.00.35, 7219.35.00.05, 7219.35.00.15, 7219.35.00.30, 7219.35.00.35, 7219.90.00.10, 7219.90.00.20, 7219.90.00.25, 7219.90.00.60, 7219.90.00.80, 7220.12.10.00, 7220.12.50.00, 7220.20.10.10, 7220.20.10.15, 7220.20.10.60, 7220.20.10.80, 7220.20.60.05, 7220.20.60.10, 7220.20.60.15, 7220.20.60.60, 7220.20.60.80, 7220.20.70.05, 7220.20.70.10, 7220.20.70.15, 7220.20.70.60, 7220.20.70.80, 7220.20.80.00, 7220.20.90.30, 7220.20.90.60, 7220.90.00.10, 7220.90.00.15, 7220.90.00.60, and 7220.90.00.80. Although the HTSUS subheadings are provided for convenience and Customs purposes, Commerce's written description of the merchandise under review is dispositive.

Excluded from the scope of this review are the following: (1) sheet and strip that is not annealed or otherwise heat treated and pickled or otherwise descaled, (2) sheet and strip that is cut to length, (3) plate ( i.e., flat-rolled stainless steel products of a thickness of 4.75 mm or more), (4) flat wire ( i.e., cold-rolled sections, with a prepared edge, rectangular in shape, of a width of not more than 9.5 mm), and (5) razor blade steel. Razor blade steel is a flat-rolled product of stainless steel, not further worked than cold-rolled (cold-reduced), in coils, of a width of not more than 23 mm and a thickness of 0.266 mm or less, containing, by weight, 12.5 to 14.5 percent chromium, and certified at the time of entry to be used in the manufacture of razor blades. See Chapter 72 of the HTSUS, “Additional U.S. Note” 1(d).

Flapper valve steel is also excluded from the scope of the review. This product is defined as stainless steel strip in coils containing, by weight, between 0.37 and 0.43 percent carbon, between 1.15 and 1.35 percent molybdenum, and between 0.20 and 0.80 percent manganese. This steel also contains, by weight, phosphorus of 0.025 percent or less, silicon of between 0.20 and 0.50 percent, and sulfur of 0.020 percent or less. The product is manufactured by means of vacuum arc remelting, with inclusion controls for sulphide of no more than 0.04 percent and for oxide of no more than 0.05 percent. Flapper valve steel has a tensile strength of between 210 and 300 ksi, yield strength of between 170 and 270 ksi, plus or minus 8 ksi, and a hardness (Hv) of between 460 and 590. Flapper valve steel is most commonly used to produce specialty flapper valves in compressors.

Also excluded is a product referred to as suspension foil, a specialty steel product used in the manufacture of suspension assemblies for computer disk drives. Suspension foil is described as 302/304 grade or 202 grade stainless steel of a thickness between 14 and 127 microns, with a thickness tolerance of plus-or-minus 2.01 microns, and surface glossiness of 200 to 700 percent Gs. Suspension foil must be supplied in coil widths of not more than 407 mm, and with a mass of 225 kg or less. Roll marks may only be visible on one side, with no scratches of measurable depth. The material must exhibit residual stresses of 2 mm maximum deflection, and flatness of 1.6 mm over 685 mm length.

Certain stainless steel foil for automotive catalytic converters is also excluded from the scope of these Orders. This stainless steel strip in coils is a specialty foil with a thickness of between 20 and 110 microns used to produce a metallic substrate with a honeycomb structure for use in automotive catalytic converters. The steel contains, by weight, carbon of no more than 0.030 percent, silicon of no more than 1.0 percent, manganese of no more than 1.0 percent, chromium of between 19 and 22 percent, aluminum of no less than 5.0 percent, phosphorus of no more than 0.045 percent, sulfur of no more than 0.03 percent, lanthanum of less than 0.002 or greater than 0.05 percent, and total rare earth elements of more than 0.06 percent, with the balance iron.

Permanent magnet iron-chromium-cobalt alloy stainless strip is also excluded from the scope of this order. This ductile stainless steel strip contains, by weight, 26 to 30 percent chromium, and 7 to 10 percent cobalt, with the remainder of iron, in widths 228.6 mm or less, and a thickness between 0.127 and 1.270 mm. It exhibits magnetic remanence between 9,000 and 12,000 gauss, and a coercivity of between 50 and 300 oersteds. This product is most commonly used in electronic sensors and is currently available under proprietary trade names such as “Arnokrome III.” ^[6]

Certain electrical resistance alloy steel is also excluded from the scope of these Orders. This product is defined as a non-magnetic stainless steel manufactured to American Society of Testing and Materials (ASTM) specification B344 and containing, by weight, 36 percent nickel, 18 percent chromium, and 46 percent iron, and is most notable for its resistance to high temperature corrosion. It has a melting point of 1390 degrees Celsius and displays a creep rupture limit of 4 kilograms per square millimeter at 1000 degrees Celsius. This steel is most commonly used in the production of heating ribbons for circuit breakers and industrial furnaces, and in rheostats for railway locomotives. The product is currently available under proprietary trade names such as “Gilphy 36.” ^[7]

Certain martensitic precipitation-hardenable stainless steel is also excluded from the scope of these Orders. This high-strength, ductile stainless steel product is designated under the Unified Numbering System (UNS) as S45500-grade steel, and contains, by weight, 11 to 13 percent chromium, and 7 to 10 percent nickel. Carbon, manganese, silicon and molybdenum each comprise, by weight, 0.05 percent or less, with phosphorus and sulfur each comprising, by weight, 0.03 percent or less. This steel has copper, niobium, and titanium added to achieve aging, and will exhibit yield strengths as high as 1700 Mpa and ultimate tensile strengths as high as 1750 Mpa after aging, with elongation percentages of 3 percent or less in 50 mm. It is generally provided in thicknesses between 0.635 and 0.787 mm, and in widths of 25.4 mm. This product is most commonly used in the manufacture of television tubes and is currently available under proprietary trade names such as “Durphynox 17.” ^[8]

Finally, three specialty stainless steels typically used in certain industrial blades and surgical and medical instruments are also excluded from the scope of these Orders. These include stainless steel strip in coils used in the production of textile cutting tools ( e.g., carpet knives).^[9] This steel is similar to AISI grade 420 but containing, by weight, 0.5 to 0.7 percent of molybdenum. The steel also contains, by weight, carbon of between 1.0 and 1.1 percent, sulfur of 0.020 percent or less, and includes between 0.20 and 0.30 percent copper and between 0.20 and 0.50 percent cobalt. This steel is sold under proprietary names such as “GIN4 Mo.” The second excluded stainless steel strip in coils is similar to AISI 420–J2 and contains, by weight, carbon of between 0.62 and 0.70 percent, silicon of between 0.20 and 0.50 percent, manganese of between 0.45 and 0.80 percent, phosphorus of no more than 0.025 percent and sulfur of no more than 0.020 percent. This steel has a carbide density on average of 100 carbide particles per 100 square microns. An example of this product is “GIN5” steel. The third specialty steel has a chemical composition similar to AISI 420 F, with carbon of between 0.37 and 0.43 percent, molybdenum of between 1.15 and 1.35 percent, but lower manganese of between 0.20 and 0.80 percent, phosphorus of no more than 0.025 percent, silicon of between 0.20 and 0.50 percent, and sulfur of no more than 0.020 percent. This product is supplied with a hardness of more than Hv 500 guaranteed after customer processing, and is supplied as, for example, “GIN6.” ^[10]

Continuation of the Orders

As a result of the determinations by Commerce and the ITC that revocation of the Orders would likely lead to continuation or recurrence of dumping, countervailable subsidies, and material injury to an industry in the United States, pursuant to section 751(d)(2) of the Act, Commerce hereby orders the continuation of the Orders. U.S. Customs and Border Protection will continue to collect AD and CVD cash deposits at the rates in effect at the time of entry for all imports of subject merchandise.

The effective date of the continuation of the Orders will be October 24, 2023.^[11] Pursuant to section 751(c)(2) of the Act and 19 CFR 351.218(c)(2), Commerce intends to initiate the next five-year reviews of the Orders not later than 30 days prior to fifth anniversary of the date of the last determination by the ITC.

Administrative Protective Order (APO)

This notice also serves as a final reminder to parties subject to an APO of their responsibility concerning the return or destruction of proprietary information disclosed under APO in accordance with 19 CFR 351.305(a)(3), which continues to govern business proprietary information in this segment of the proceedings. Timely written notification of the return or destruction of APO materials, or conversion to judicial protective order, is hereby requested. Failure to comply with the regulations and terms of an APO is a violation which is subject to sanction.

Notification to Interested Parties

These five-year (sunset) reviews and this notice are in accordance with sections 751(c) and 751(d)(2) of the Act and published in accordance with section 777(i) of the Act and 19 CFR 351.218(f)(4).

Dated: December 1, 2023.

Abdelali Elouaradia,

Deputy Assistant Secretary for Enforcement and Compliance.

Footnotes

1.   See Notice of Antidumping Duty Order: Stainless Steel Sheet and Strip in Coils from United Kingdom, Taiwan, and South Korea,64 FR 40555 (July 27, 1999); Notice of Amended Final Determination of Sales at Less Than Fair Value and Antidumping Duty Order: Stainless Steel Sheet and Strip in Coils from Japan,64 FR 40565 (July 27, 1999; and Amended Final Determination: Stainless Steel Sheet and Strip in Coils from the Republic of Korea; and Notice of Countervailing Duty Orders: Stainless Steel Sheet and Strip in Coils from France, Italy, and the Republic of Korea,64 FR 42923 (August 6, 1999) (collectively, Orders).

2.   See Stainless Steel Sheet and Strip from Japan, Korea, and Taiwan; Institution of Five-Year Review,87 FR 53780 (September 1, 2022).

3.   See Initiation of Five-Year (“Sunset”) Review,87 FR 53727 (September 1, 2022).

4.   See Stainless Steel Sheet and Strip in Coils from Japan, the Republic of Korea, and Taiwan: Final Results of the Expedited Fourth Sunset Review of the Antidumping Duty Orders,87 FR 74133 (December 2, 2022), and accompanying Issues and Decision Memorandum (IDM); and Stainless Steel Sheet and Strip in Coils from the Republic of Korea: Final Results of Expedited Sunset Review of the Countervailing Duty Order,87 FR 74130 (December 2, 2022), and accompanying IDM.

5.   See Stainless Steel Sheet and Strip from Japan, South Korea, and Taiwan Determinations,88 FR 73043 (October 24, 2023) ( ITC Final Determination).

6.  “Arnokrome III” is a trademark of the Arnold Engineering Company.

7.  “Gilphy 36” is a trademark of Imphy, S.A.

8.  “Durphynox 17” is a trademark of Imphy, S.A.

9.  This list of uses is illustrative and provided for descriptive purposes only.

10.  “GIN4 Mo,” “GIN5” and “GIN6” are the proprietary grades of Hitachi Metals America, Ltd.

11.   See ITC Final Determination.