[Federal Register Volume 66, Number 27 (Thursday, February 8, 2001)]
[Corrections]
[Pages 9635-9636]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: C0-24472]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Parts 413, 415, and 417
[Docket No. FAA-2000-7953; Notice No. 00-10]
RIN 2120-AG37
Licensing and Safety Requirements for Launch
Correction
In proposed rule document 00-24472 beginning on page 63922 in the
issue of Wednesday, October 25, 2000, make the following corrections:
1. On page 63922, in the first column, the docket number is
corrected to read as set forth above.
Sec. 417.233 [Corrected]
2. On page 64022, in the second column, in Sec. 417.233(c)(5)(ii),
in the fourth line, after ``the'' add ``EFG''.
Appendix A to 417 [Corrected]
3. On page 64043, in the second column, in paragraph (ii), in the
fifth line, ``1 x 100@5'' should read ``1 x
10@5''.
4. On page 64044, in the second column, in paragraph (7), in the
eighth line, ``(i.e. log10)Pc'' should read
``(i.e. log10(Pc'').
Appendix B to Part 417 [Corrected]
5. On page 64051, in the first column, in the value description of
y, ``diviation'' should read ``deviation ''.
Appendix C to Part 417 [Corrected]
6. On page 64058, table C417-1 is corrected to read as set forth
below:
Table C417-1, Illustrative Simulation Runs Required to Determine Drag Impact Point Dispersions for a Three Stage
Launch Vehicle
----------------------------------------------------------------------------------------------------------------
Dispersion being determined
Trajectory simulation runs Stage performance error --------------------------------------------------
parameters Stage 1 Stage 2 Stage 3
----------------------------------------------------------------------------------------------------------------
Stage 1 errors............................................... X \1\ ............... ...............
Stage 1 errors, Stage 2 nominal.............................. ............... X ...............
Stage 1 nominal, Stage 2 errors.............................. ............... X ...............
Stage 1 errors, Stage 2 nominal, Stage 3 nominal............. ............... ............... X
Stage 1 nominal, Stage 2 errors, Stage 3 nominal............. ............... ............... X
Stage 1 nominal, Stage 2 nominal, Stage 3 errors............. ............... ............... X
----------------------------------------------------------------------------------------------------------------
\1\ An X in a given stage column indicates that the noted simulation runs are required to determine the
dispersion for that stage.
[[Page 9636]]
Appendix E to Part 417 [Corrected]
7. On page 64091, in table E417.25-3, under the ``Quality''
heading, after each ``100'' entry, add a ``%'' sign.
8. On page 64094, the second table heading, ``Table E417.25-75''
should read ``Table E417.25-7''.
9. On page 64096, in table E417.27-2, for the entry ``Performance
Verification'' remove the ``X'' in each column.
10. On the same page, in the same table, for the entry ``Non-
Operating Environment Tests'' remove the ``X '' in each column.
11. On page 64099, in table E417.27-5, for the entry ``High
Temperature Storage'', remove the ``X'' in the column named ``1
year\4\''.
12. On page 64101, in table E417.29-2, for the entry ``Firing
Test'', in the Reference column, ``E417.(g)'' should read
``E417.29(g)''.
13. On page 64104, in table E417.31-2, for the entry ``Non-
Operating Environment Tests and Operating Environment Tests'', remove
the ``X'' in the third column.
14. On the same page, in table E417.31-3, under the ``Quality''
heading, before each ``100%'' entry, remove the footnote reference
``\1\''.
15. On page 64105, in table E417.31-4, for the entry ``Low
Temperature'', remove the ``5'' in the column named ``105 ''.
16. On page 64107, in table E417.33-3, for the entry ``Component
Examination'', remove the ``X'' in each column.
17. On page 64109, in table E417-37-1, under the entry ``Shock'',
add an ``X'' in the ``Quantity'' column.
[FR Doc. C0-24472 Filed 2-7-01; 8:45 am]
BILLING CODE 1505-01-D
