E9-9866. Airworthiness Directives; Bombardier Model CL-600-2C10 (Regional Jet Series 700, 701 & 702), CL-600-2D15 (Regional Jet Series 705), and CL-600-2D24 (Regional Jet Series 900) Airplanes

AGENCY:

Federal Aviation Administration (FAA), DOT.

ACTION:

Notice of proposed rulemaking (NPRM).

SUMMARY:

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

A change in dimensions of the fuse blocks in the Auxiliary Power Unit (APU) Start Contactor Assembly (ASCA) box assembly can cause an incorrect interface between the bus bars and fuses. This condition can result in an increase in temperature, which could damage the ASCA box and/or compromise the availability of battery bus supply.

The unsafe condition could result in the ignition of a fire in the ASCA box. The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI.

DATES:

We must receive comments on this proposed AD by June 1, 2009.

ADDRESSES:

You may send comments by any of the following methods:

• Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
• Fax: [phone].
• Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590.
• Hand Delivery: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this proposed AD, contact Bombardier, Inc., 400 Côte-Vertu Road West, Dorval, Québec H4S 1Y9, Canada; telephone [phone]; fax [phone]; e-mail [e-mail]; Internet http://www.bombardier.com.

You may review copies of the referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221 or 425-227-1152.

Examining the AD Docket

You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone [phone]) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT:

Wing Chan, Aerospace Engineer, Systems and Flight Test Branch, ANE-172, FAA, New York Aircraft Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New York 11590; telephone [phone]; fax [phone].

SUPPLEMENTARY INFORMATION:

Comments Invited

We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include “Docket No. FAA-2009-0399; Directorate Identifier 2008-NM-226-AD” at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments.

We will post all comments we receive, without change, to http://www.regulations.gov,, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD.

Discussion

Transport Canada Civil Aviation (TCCA), which is the aviation authority for Canada, has issued Canadian Airworthiness Directive CF-2008-34, dated December 2, 2008 (referred to after this as “the MCAI”), to correct an unsafe condition for the specified products. The MCAI states:

A change in dimensions of the fuse blocks in the Auxiliary Power Unit (APU) Start Contactor Assembly (ASCA) box assembly can cause an incorrect interface between the bus bars and fuses. This condition can result in an increase in temperature, which could damage the ASCA box and/or compromise the availability of battery bus supply.

The unsafe condition could result in the ignition of a fire in the ASCA box. The required actions include inspecting the ASCA boxes to determine the part number; and for certain ASCA boxes, doing a detailed inspection of the fuse block date code, and replacement of the fuse block with new hardware if necessary. You may obtain further information by examining the MCAI in the AD docket.

Relevant Service Information

Bombardier has issued Service Bulletin 670BA-49-012, Revision A, dated August 28, 2008. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design.

Differences Between This AD and the MCAI or Service Information

We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.

We might also have proposed different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are highlighted in a NOTE within the proposed AD.

Costs of Compliance

Based on the service information, we estimate that this proposed AD would affect about 108 products of U.S. registry. We also estimate that it would take about 5 work-hours per product to comply with the basic requirements of this proposed AD. The average labor rate is $80 per work-hour. Based on these figures, we estimate the cost of the proposed AD on U.S. operators to be $43,200, or $400 per product.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. “Subtitle VII: Aviation Programs,” describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in “Subtitle VII, Part A, Subpart III, Section 44701: General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed regulation:

1. Is not a “significant regulatory action” under Executive Order 12866;

2. Is not a “significant rule” under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

• Air transportation
• Aircraft
• Aviation safety
• Incorporation by reference
• Safety

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39—AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13

[Amended]

2. The FAA amends § 39.13 by adding the following new AD:

Bombardier (Formerly Canadair): Docket No. FAA-2009-0399; Directorate Identifier 2008-NM-226-AD.

Comments Due Date

(a) We must receive comments by June 1, 2009.

Affected ADs

(b) None.

Applicability

(c) This AD applies to the airplanes, certificated in any category, identified in paragraphs (c)(1) and (c)(2) of this AD.

(1) Bombardier Model CL-600-2C10 (Regional Jet Series 700, 701 & 702), serial numbers 10112 through 10199, and 10201 through 10206.

(2) Bombardier Model CL-600-2D15 (Regional Jet Series 705) and CL-600-2D24 (Regional Jet Series 900), serial numbers 15007 through 15026, 15030, and 15031.

Subject

(d) Air Transport Association (ATA) of America Code 49: Airborne Auxiliary Power.

Reason

(e) The mandatory continuing airworthiness information (MCAI) states:

A change in dimensions of the fuse blocks in the Auxiliary Power Unit (APU) Start Contactor Assembly (ASCA) box assembly can cause an incorrect interface between the bus bars and fuses. This condition can result in an increase in temperature, which could damage the ASCA box and/or compromise the availability of battery bus supply.

The unsafe condition could result in the ignition of a fire in the ASCA box. The required actions include inspecting the ASCA boxes to determine the part number; and for certain ASCA boxes, doing a detailed inspection of the fuse block date code, and replacement of the fuse block with new hardware if necessary.

Actions and Compliance

(f) Unless already done, do the following actions:

(1) Within 1,500 flight hours after the effective date of this AD, perform an inspection of the ASCA box to determine the part number and, for ASCA boxes having part number BA670-53328-1 or BA670-53328-951, perform a detailed inspection of the fuse block date code, in accordance with Bombardier Service Bulletin 670BA-49-012, Revision A, dated August 28, 2008. Before further flight, replace all fuse blocks that have a date code between K23 (0323) through M08 (0508) inclusive, in accordance with Bombardier Service Bulletin 670BA-49-012, Revision A, dated August 28, 2008.

(2) Inspections and replacement actions are also acceptable for compliance with the requirements of paragraph (f)(1) of this AD, if done before the effective date of this AD in accordance with Bombardier Service Bulletin 670BA-49-012, dated June 28, 2007.

FAA AD Differences

Note 1:

This AD differs from the MCAI and/or service information as follows: No Differences.

Other FAA AD Provisions

(g) The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs): The Manager, Systems and Flight Test Branch, ANE-172, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Wing Chan, Aerospace Engineer, Systems and Flight Test Branch, ANE-172, FAA, New York Aircraft Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New York 11590; telephone [phone]; fax [phone]. Before using any approved AMOC on any airplane to which the AMOC applies, notify your principal maintenance inspector (PMI) or principal avionics inspector (PAI), as appropriate, or lacking a principal inspector, your local Flight Standards District Office.

(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service.

(3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act, the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056.

Related Information

(h) Refer to MCAI Transport Canada Civil Aviation Airworthiness Directive CF-2008-34, dated December 2, 2008; and Bombardier Service Bulletin 670BA-49-012, Revision A, dated August 28, 2008; for related information.

Issued in Renton, Washington, on April 22, 2009.

Stephen P. Boyd,

Acting Manager, Transport Airplane Directorate, Aircraft Certification Service.