2019-08699. Test Procedure Interim Waiver Process  

  • Start Preamble Start Printed Page 18414

    AGENCY:

    Office of Energy Efficiency and Renewable Energy, U.S. Department of Energy.

    ACTION:

    Notice of proposed rulemaking; request for comment.

    SUMMARY:

    The U.S. Department of Energy (DOE) proposes to streamline its test procedure waiver decision-making process to require the Department to notify, in writing, an applicant for an interim waiver of the disposition of the request within 30 business days of receipt of the application. Should DOE fail to satisfy this requirement, the request for interim waiver would be deemed granted based on the criteria in DOE regulations. Specifically, DOE regulations require that DOE grant an interim waiver if it determines that it is desirable for public policy reasons to grant immediate relief pending a determination of the petition for waiver. An interim waiver would remain in effect until a waiver decision is published or until DOE publishes a new or amended test procedure that addresses the issues presented in the application, whichever is earlier. This proposal is intended to address delays in DOE's current process for considering requests for interim waivers and waivers from the DOE test method, which in turn can result in significant delays for manufacturers in bringing new and innovative products to market.

    DATES:

    The comment period for this proposed rule will end on July 1, 2019.

    ADDRESSES:

    You may submit comments, identified by docket number [EERE-2019-BT-NOA-0011], and/or Regulation Identification Number (RIN) 1904-AE24 in one of four ways (please select only one of the ways listed):

    1. Federal e-Rulemaking Portal: http://www.regulations.gov. Follow the instructions for submitting comments.

    2. Email: TPWaiverProcess2019NOA0011@ee.doe.gov. Include docket number [EERE-2019-BT-NOA-0011] and/or RIN 1904-AE24 in the subject line of the email. Please include the full body of your comments in the text of the message or as an attachment. If you have additional information such as studies or journal articles and cannot attach them to your electronic submission, please send them on a CD or USB flash drive to the address listed in paragraph 4. The additional material must clearly identify your electronic comments by name, date, subject, and docket number [EERE-2019-BT-NOA-0011].

    3. Mail: Address written comments to Appliance and Equipment Standards Program, U.S. Department of Energy, Building Technologies Office, Mailstop EE-5B, 1000 Independence Avenue SW, Washington, DC 20585-0121 (due to potential delays in DOE's receipt and processing of mail sent through the U.S. Postal Service, we encourage respondents to submit comments electronically to ensure timely receipt). If possible, please submit all items on a CD or USB flash drive, in which case it is not necessary to include printed copies.

    4. Hand Delivery/Courier: Appliance and Equipment Standards Program, U.S. Department of Energy, Building Technologies Office, 950 L'Enfant Plaza SW, Suite 600, Washington, DC 20024. Telephone (202) 287-1445. If possible, please submit all items on a CD or USB flash drive, in which case it is not necessary to include printed copies.

    For detailed instructions on submitting comments and additional information on the rulemaking process, see Section IV of this document (Public Participation).

    Docket: The docket, which includes Federal Register notices, public meeting attendee lists and transcripts, comments, and other supporting documents/materials, is available for review at http://www.regulations.gov. All documents in the docket are listed in the http://www.regulations.gov index. However, some documents listed in the index, such as those containing information that is exempt from public disclosure, may not be publicly available. A link to the docket web page can be found at: http://www.regulations.gov/​docket?​D=​EERE-2019-BT-NOA-0011. The http://www.regulations.gov web page contains instructions on how to access all documents, including public comments, in the docket. See Section IV of this document (Public Participation) for further information on how to submit comments through http://www.regulations.gov.

    Start Further Info

    FOR FURTHER INFORMATION CONTACT:

    Ms. Jennifer Tiedeman, U.S. Department of Energy, Office of the General Counsel, GC-33, 1000 Independence Avenue SW, Washington, DC 20585-0121. Telephone: (202) 287-6111. Email: Jennifer.Tiedeman@hq.doe.gov.

    End Further Info End Preamble Start Supplemental Information

    SUPPLEMENTARY INFORMATION:

    I. Legal Background

    II. Discussion of Proposed Amendments

    III. Discussion of Data

    IV. Procedural Requirements

    A. Review Under Executive Orders 12866 and 13563

    B. Review Under Executive Orders 13771 and 13777

    C. Review Under the Regulatory Flexibility Act

    D. Review Under the Paperwork Reduction Act

    E. Review Under the National Environmental Policy Act

    F. Review Under Executive Order 12988

    G. Review Under Executive Order 13132

    H. Review Under Executive Order 13175

    I. Review Under the Unfunded Mandates Reform Act of 1995

    J. Review Under Executive Order 13211

    K. Review Under the Treasury and General Government Appropriations Act, 1999

    L. Review Under the Treasury and General Government Appropriations Act, 2001

    V. Public Participation

    A. Submission of Information

    B. Issues on Which DOE Seeks Information

    VI. Approval of the Office of the Secretary

    I. Legal Background

    The Energy Policy and Conservation Act of 1975 (“EPCA” or “the Act”),[1] Public Law 94-163 (42 U.S.C. 6291-6317) authorizes DOE to regulate the energy efficiency of a number of consumer products and industrial equipment types. Title III, Part B [2] of EPCA established the Energy Conservation Program for Consumer Products Other Than Automobiles. Title Start Printed Page 18415III, Part C [3] of EPCA established the Energy Conservation Program for Certain Industrial Equipment. Under EPCA, DOE's energy conservation program consists essentially of four parts: (1) Testing, (2) labeling, (3) Federal energy conservation standards, and (4) certification and enforcement procedures.

    The Federal testing requirements consist of test procedures that manufacturers of covered products and equipment must use as the basis for: (1) Certifying to DOE that their products or equipment complies with the applicable energy conservation standards adopted pursuant to EPCA (42 U.S.C. 6295(s); 42 U.S.C. 6316(a)), and (2) making representations about the efficiency of those products or equipment (42 U.S.C. 6293(c); 42 U.S.C. 6314(d)). Similarly, DOE must use these test procedures to determine whether the products or equipment complies with relevant standards promulgated under EPCA. (42 U.S.C. 6295(s); 42 U.S.C.6316 (a))

    Under 42 U.S.C. 6293 and 6314, EPCA sets forth the criteria and procedures DOE is required to follow when prescribing or amending test procedures for covered products and equipment. EPCA requires that test procedures must be reasonably designed to produce test results that reflect energy efficiency, energy use or estimated annual operating cost of a covered product or covered equipment during a representative average use cycle or period of use and requires that test procedures not be unduly burdensome to conduct (42 U.S.C. 6293(b)(3); 42 U.S.C. 6314(a)(2)). DOE's regulations provide that upon receipt of a petition, DOE will grant a waiver from the test procedure requirements if DOE determines either that the basic model for which the waiver was requested contains a design characteristic that prevents testing of the basic model according to the prescribed test procedures, or that the prescribed test procedures evaluate the basic model in a manner so unrepresentative of its true energy consumption characteristics as to provide materially inaccurate comparative data. 10 CFR 430.27(a)(1) and 10 CFR 431.401(f)(2). DOE may grant the waiver subject to conditions, including adherence to alternate test procedures.

    In addition to the full waiver (“decision and order”) described above, the waiver process permits parties submitting a petition for waiver to also file an application for interim waiver from the applicable test procedure requirements. 10 CFR 430.27(a) and 10 CFR 431.401(a). The current regulations specify that, if administratively feasible, DOE will notify the applicant in writing of the disposition of a petition for interim waiver within 30 business days of receipt of the application. The Assistant Secretary will grant an interim waiver if it appears likely that the petition for waiver will be granted, and/or the Assistant Secretary determines that it would be desirable for public policy reasons to grant immediate relief pending a determination of the petition for waiver. 10 CFR 430.27(e)(2) and 10 CFR 430.401(e)(2). Notice of DOE's determination on the petition for interim waiver will also be published in the Federal Register. 10 CFR 430.27(e)(1) and 10 CFR 431.401(e)(1). Within one year of issuance of an interim waiver, DOE will either: (i) Publish in the Federal Register a determination on the petition for waiver; or (ii) publish in the Federal Register a new or amended test procedure that addresses the issues presented in the waiver. 10 CFR 430.27(h)(1) and 10 CFR 431.401(h)(2). When DOE amends the test procedure to address the issues presented in a waiver, the waiver will automatically terminate on the date on which use of that test procedure is required to demonstrate compliance. 10 CFR 430.27(h)(2) and 10 CFR 431.401(h)(2).

    II. Discussion of Proposed Amendments

    In this proposed rule, DOE is proposing amendments to its regulations that would reduce manufacturers' burden associated with the interim waiver application process, provide them with greater certainty, and speed the availability of innovative product options to consumers. DOE's proposal responds to stakeholder concerns regarding lengthy waiting times following submission of interim waiver and waiver applications, and the burden that lengthy processing time imposes on manufacturers, who are unable to sell their products or equipment absent an interim waiver or waiver from DOE.[4] This burden may be especially pronounced for manufacturers of seasonal appliances, such as room air conditioners, in cases where interim waiver delays cause a product to miss the applicable seasonal sale window.

    Specifically, this proposal is intended to address delays in DOE's current process for considering requests for interim waivers and waivers from the DOE test method, which in turn can result in significant delays for manufacturers in bringing new and innovative products to market. DOE has in the past incurred delays by not responding to petitions in a timely manner, and this delay has imposed negative consequences for manufacturers who cannot bring their products to market absent a waiver from the Department that allows them to test their products and certify them as compliant with DOE energy conservation standards. Additional information on the length and cost to manufacturers of the delays is described in Section III. DOE's proposal would ensure that manufacturers would need to wait only a maximum of 30 business days before selling products under an approved interim waiver. If the petition for waiver ultimately requires the use of a different test method than that granted under the interim waiver, manufacturers would have an additional grace period of 180 days to begin using the test method required by the waiver.

    DOE regulations currently require the Department to notify an applicant in writing of the disposition of a petition for interim waiver within 30 business days of receipt of the application “[i]f administratively feasible.” 10 CFR 430.27(e)(1) and 10 CFR 431.401(e)(1). DOE proposes in this notice to amend 10 CFR 430.27(e)(1) and 10 CFR 431.401(e)(1) to require the Department to issue decisions on interim waiver applications within 30 business days, removing the language “[i]f administratively feasible.” Under the proposal, an application for interim waiver would be deemed granted, thereby permitting use of the alternate test procedure suggested by the applicant in its application, if DOE fails to notify the applicant in writing of the disposition of an application within 30 business days of receipt of the application. DOE's decision on the interim waiver request will not depend on DOE's view of the sufficiency of the associated petition for waiver, because DOE can work with the petitioner to gather any additional information or conduct any additional analysis deemed necessary to reach a decision on the petition while the manufacturer is able to sell the product or equipment at issue under the interim waiver. DOE's regulations specify that DOE may grant an interim waiver if DOE determines that it would be desirable for public policy reasons to grant immediate relief pending a determination of the

    petition for waiver. 10 CFR 430.27(e)(2) and 10 CFR 430.401(e)(2). Start Printed Page 18416

    Because manufacturers may not distribute covered products or equipment in commerce without demonstrating compliance with an applicable energy conservation standard pursuant to testing under the DOE test procedure or a waiver or interim waiver approved by DOE, DOE determines that it is desirable for public policy reasons, including burden reduction on regulated parties and administrative efficiency, to grant immediate relief on each application for interim waiver where DOE has not notified the applicant of its interim waiver decision within the 30-business day period.[5]

    This proposal would dovetail with DOE's proposed amendments to 10 CFR 430.27(h) and 10 CFR 431.401(h), which would specify that an interim waiver remains in effect until the earlier of the following: (1) DOE publishes in the Federal Register a determination on the petition for waiver or (2) DOE publishes in the Federal Register a new or amended test procedure that addresses the issues presented in the waiver application. Under these proposals, manufacturers would receive a decision on their application from DOE within a reasonable time period and would no longer be precluded from distributing covered products or equipment in commerce while waiting for DOE to conclude its analysis, which often stretches significantly beyond 30 business days (see section III, Discussion of Data).

    DOE's intent in issuing these proposals is to provide certainty to regulated entities while reducing regulatory burden and achieving cost savings for manufacturers by reducing the delay in revenue from products pending an interim waiver. Manufacturers who cannot test their products under the DOE test procedure or for whom use of the test procedure produces results that do not reflect the energy consumption of their products cannot sell their products absent an interim waiver or waiver from DOE. To the extent that DOE previously has issued interim waiver decisions in excess of 30 business days after receipt of petitions, the time saved under this proposal is expected to significantly reduce the costs imposed on these manufacturers who cannot sell their products during the time it takes DOE to process an application for interim waiver or waiver request. Additionally, the certainty of a prescribed period prior to the issuance of a decision by the Department should provide manufacturers better information with which to plan for testing requirements. Manufacturers would also be able to proceed with distribution under the interim waiver pending any decision on a waiver application or publication of a new or amended test procedure by the Department. The expected cost savings from this proposed rule, if adopted, are discussed in Section III of this document.

    DOE also proposes that if DOE ultimately denies the petition for waiver or grants the petition with a different alternate test procedure than specified in the interim waiver, DOE will provide a grace period of 180 days for the manufacturer to begin to use the alternate test procedure specified in the decision and order on the petition. This is consistent with the EPCA provision providing 180 days from issuance of a new or amended test procedure for manufacturers to begin using the test procedure for representations of energy efficiency. See 42 U.S.C. 6293(c)(2).

    Issue: DOE requests comment on its proposal to specify that an interim waiver would remain in effect until the earlier of the following: A waiver decision is published or DOE publishes a new or amended test procedure that addresses the issues presented in the waiver.

    III. Discussion of Data

    DOE has reviewed data on the time lags between receipt of an application for interim waiver and issuance of an interim waiver. To the extent that this proposed change would deem as granted interim waiver applications that would be eventually granted under DOE's current process for granting waivers, DOE anticipates cost savings to accrue to manufacturers and consumer surplus to accrue to consumers who benefit from the timely availability of desired products.

    Between 2016 and 2018, DOE received 40 waiver applications, 33 of which also included a request for an interim waiver. Of these, two waivers were withdrawn and one waiver was delayed pending ongoing litigation. DOE presents data on the remaining 37 waiver applications below.[6]

    Total Waivers Requested 2016-2018

    Waivers requested40
    % of waivers concluded in under 1 year69
    % of waivers concluded in over 1 year31
    Interim waivers requested32
    % of interim waivers concluded in under 100 days20
    % of interim waivers concluded in more than 100 days80

    Although DOE regulations specify that, if administratively feasible, DOE will notify the applicant in writing of the disposition of a petition for interim waiver within 30 business days of receipt of the application, only one of the interim waiver requests in this dataset met this timeframe; one-fifth of interim waiver requests were resolved in under 100 days. On average, interim waiver requests received in 2016 took 162 days to resolve; those received in 2017 took 202 days on average, and those received in 2018 took on average 208 days.[7] This significantly exceeds DOE's objective of turning around interim waiver petitions within 30 business days, or approximately 45 Start Printed Page 18417days. In 2017 alone, four requests for interim waiver took longer than 350 days each to resolve.

    This time lag between submission of waiver and interim waiver requests and DOE's decision on interim waivers would be somewhat less significant if waiver decisions and orders were issued in a timely manner. However, on average it took DOE nearly one year to issue decisions and orders on waiver petitions submitted in 2016 and 2017.8 As of this writing, DOE had one outstanding petition for waiver from 2016 and 3 outstanding petitions submitted in 2017, and has yet to reach a decision on 90% of the petitions for waiver received in 2018. These data illustrate the need for issuance of a timely interim waiver while the full waiver application is pending. Enhancing the efficiency of DOE's interim waiver approval process has the potential to reduce uncertainty for manufacturers and provide consumers with more options.

    Issue: DOE requests comment on the length of time manufacturers have previously waited for DOE to provide notification of the disposition of applications for interim waiver (or final decisions on waiver petitions), and the correlated extent of cost savings and any other benefits they expect to realize as a result of the proposal to specify in the regulations that if the Department fails to issue an interim waiver decision within 30 business days following receipt of an application, the application is deemed granted. DOE seeks, in particular, comment on whether interim waiver delays have affected the availability of seasonal products during peak season, and the effects of these delays on manufacturers and consumers.

    IV. Procedural Requirements

    A. Review Under Executive Order 12866 and 13563

    This regulatory action has been determined to be “significant” under Executive Order 12866, “Regulatory Planning and Review” (58 FR 51735, October 4, 1993). Accordingly, this action was subject to review under that Executive Order by the Office of Information and Regulatory Affairs (OIRA) of the Office of Management and Budget (OMB).

    DOE has also reviewed this proposed regulation pursuant to Executive Order 13563, issued on January 18, 2011 (76 FR 3281, Jan. 21, 2011). E.O. 13563 is supplemental to and explicitly reaffirms the principles, structures, and definitions governing regulatory review established in Executive Order 12866. To the extent permitted by law, agencies are required by Executive Order 13563 to: (1) Propose or adopt a regulation only upon a reasoned determination that its benefits justify its costs (recognizing that some benefits and costs are difficult to quantify); (2) tailor regulations to impose the least burden on society, consistent with obtaining regulatory objectives, taking into account, among other things, and to the extent practicable, the costs of cumulative regulations; (3) select, in choosing among alternative regulatory approaches, those approaches that maximize net benefits (including potential economic, environmental, public health and safety, and other advantages; distributive impacts; and equity); (4) to the extent feasible, specify performance objectives, rather than specifying the behavior or manner of compliance that regulated entities must adopt; and (5) identify and assess available alternatives to direct regulation, including providing economic incentives to encourage the desired behavior, such as user fees or marketable permits, or providing information upon which choices can be made by the public. DOE concludes that this proposed rule is consistent with these principles. The proposed amendments to DOE's regulations are intended to expedite DOE's processing of test procedure interim waiver applications, thereby reducing financial and administrative burdens for all manufacturers; as such, the proposed Start Printed Page 18418rule satisfies the criteria in Executive Order 13563.

    B. Review Under Executive Orders 13771 and 13777

    On January 30, 2017, the President issued Executive Order 13771, “Reducing Regulation and Controlling Regulatory Costs.” That Order stated the policy of the executive branch is to be prudent and financially responsible in the expenditure of funds, from both public and private sources. The Order stated that it is essential to manage the costs associated with the governmental imposition of private expenditures required to comply with Federal regulations. DOE considers this proposed rule to be an E.O. 13771 deregulatory action, resulting in expected cost savings to manufacturers.

    Additionally, on February 24, 2017, the President issued Executive Order 13777, “Enforcing the Regulatory Reform Agenda.” The Order required the head of each agency designate an agency official as its Regulatory Reform Officer (RRO). Each RRO shall oversee the implementation of regulatory reform initiatives and policies to ensure that agencies effectively carry out regulatory reforms, consistent with applicable law. Further, E.O. 13777 requires the establishment of a regulatory task force at each agency. The regulatory task force will make recommendations to the agency head regarding the repeal, replacement, or modification of existing regulations, consistent with applicable law. At a minimum, each regulatory reform task force shall attempt to identify regulations that:

    (i) Eliminate jobs, or inhibit job creation;

    (ii) Are outdated, unnecessary, or ineffective;

    (iii) Impose costs that exceed benefits;

    (iv) Create a serious inconsistency or otherwise interfere with regulatory reform initiatives and policies;

    (v) Are inconsistent with the requirements of Information Quality Act, or the guidance issued pursuant to that Act, in particular those regulations that rely in whole or in part on data, information, or methods that are not publicly available or that are insufficiently transparent to meet the standard for reproducibility; or

    (vi) Derive from or implement Executive Orders or other Presidential directives that have been subsequently rescinded or substantially modified.

    As noted, this proposed rule is deregulatory, and is expected to reduce both financial and administrative burdens on regulated parties. Specifically, the proposed amendments to DOE's regulations discussed in the proposal should improve upon current waiver regulations, which potentially are inhibiting job creation; are ineffective in creating certainty for manufacturers with respect to business decisions; and impose costs that exceed benefits. Specifically, the length of time manufacturers have previously waited for DOE to provide notification of the disposition of applications for interim waiver (or final decisions on waiver petitions), made possible by the open-ended nature of the current regulations, would be significantly shortened by the current proposal. As noted above, the cost savings and other benefits manufacturers should realize by waiting no more than 30 days for an interim waiver should create cost savings, as manufacturers would be able to introduce their products and equipment into commerce in a timely fashion. These cost savings may lead to increased job creation, and create other potentially significant economic benefits.

    i. National Cost Savings and Foregone Benefits

    The primary anticipated cost saving is from reducing the number of days by which manufacturer revenues are delayed for affected products. This value is monetized using the interest that a manufacturer might have earned on product revenue if an interim waiver were approved within 30 business days (approximately 45 days). On average, between 2016 and 2018, DOE concluded interim waivers after 185 days, or 140 days beyond the 30 business days specified in DOE's regulations. DOE uses 7% interest per the Office of Management and Budget's Circular A-4,[9] and calculates the foregone interest that could have accrued for each affected product during the 140 day delay period.

    DOE monetized the scope of delay using average prices for products in interim waiver petitions and the proportion of affected shipments, based on the proportion of basic models listed in interim waiver petitions relative to the total number of basic models within each product category. A full list of petitions for interim waiver can be accessed at https://www.energy.gov/​eere/​buildings/​current-test-procedure-waivers. This list indicates how many interim waiver petitions were received for each product category. Each petition for interim waiver also lists the number of affected basic models, which DOE used to assess the proportion of shipments affected by each petition. Total numbers of basic models per product category are accessible via the DOE's Compliance Certification Database.[10]

    Between 2016 and 2018, 5,322 basic models of 12 residential and commercial products were affected by interim waiver delays, totaling 1.31 million in estimated annual shipments and $1.76 billion in annual sales. The affected products are outlined in Table IV.B.1 below.[11] While all affected shipments are represented in Table IV.B.1 below, DOE monetized the cost of delay only for those basic models for which manufacturers would be unable to test or certify absent an interim waiver. For one petition, the manufacturer was unable to test or certify half of the basic models requested absent a waiver; the estimated cost of delay is proportionate to those models. DOE calculated the interest that could have been earned on this revenue over the 140-day average delay period and multiplied the average cost of delay per petition by 11, the average number of interim waiver requests received per year, to reach an annual cost of delay. In undiscounted terms, DOE expects that this proposal will result in $17.3 million in annual cost savings. DOE assumes that these sales are delayed rather than foregone.

    Start Printed Page 18419

    Table IV.B.1—Shipments and Average Prices of Products/Equipment Affected by Interim Waiver Delays 2016-2018

    Product/equipmentAffected shipmentsAverage price (2016$) 12Estimated product salesCost of delay
    Residential
    Battery Chargers74,694$7.92$591,738$16,569
    Ceiling Fans48,397110.435,344,688149,651
    Central Air Conditioners & Heat Pumps481,2003,086.071,371,615,82938,405,243
    Clothes Washers31,780700.2422,253,510623,098
    Dishwashers24,912301.927,521,486210,602
    Refrigerators40,968655.3026,846,375751,699
    Commercial
    Commercial Refrigeration Equipment22,0363,902.7185,998,1892,407,949
    Walk-in Coolers & Freezers—Doors190,950585.60111,821,2713,097,477
    Walk-in Coolers & Freezers—Systems7002,681.821,876,01152,528
    Total45,714,816
    Average Cost of Delay per Petition (29 petitions total)1,576,373
    Average Cost of Delay per Year (11 petitions/year)17,340,103
    Note that totals may not add due to rounding.

    Foregone Benefits

    To the extent that this policy would cause DOE to automatically grant interim waiver requests that it would not have granted in the status quo, this proposal may result in foregone benefits to consumers or the environment. Based on historical data, these effects are anticipated to be relatively small. Of 21 concluded interim waiver petitions, DOE granted 18 in full and granted the remaining 3 with modifications. Of the modified interim waivers, one was granted in part, one was granted with minor modifications, and one was granted with a different alternative test measure than proposed. DOE estimated the foregone environmental benefits and energy savings of granting the petitions as received, rather than as modified by the Department.

    All foregone benefits and savings are annual, rather than one-time, and are projected in the table below using a perpetual time horizon and discounted to 2016. DOE expects these changes to result in $457.7 million or $204.4 million in total cost savings, discounted at 3% and 7%, respectively. In annualized terms, DOE expects $13.7 million in net cost savings, discounted at 3%, or $14.3 million in net cost savings discounted at 7%.

    Table IV.B.2—Cost Impact of Proposed Interim Waiver Rule (2016$)

    Costs or (Savings)Costs or (Savings) millions
    Annual Cost Savings of Reduced Delay($17,340,000)($17.34)
    Annual Foregone Energy Savings$164,000$0.16
    Annualized Carbon Emissions (SCC), 3% †$1,764,000$1.76
    Annualized Carbon Emissions (SCC), 7% †$827,000$0.83
    Net Present Value at 3%($457,763,000)($457.76)
    Net Present Value at 7%($204,428,000)($204.43)
    Annualized Costs or (Savings) at 3%($13,733,000)($13.73)
    Annualized Costs or (Savings) at 7%($14,310,000)($14.31)
     Undiscounted annual SCC values are not available for comparison.

    C. Review Under the Regulatory Flexibility Act

    The Regulatory Flexibility Act of 1980 (5 U.S.C. 601 et seq.) requires that a Federal agency prepare an initial regulatory flexibility analysis for any regulation for which a general notice of proposed rulemaking is required, unless the agency certifies that the rule, if promulgated, will not have a significant economic impact on a substantial number of small entities (5 U.S.C. 605(b)).

    This proposed rule would impose a requirement on the Department that it must make a decision on interim waiver applications within 30 business days after receipt of a petition. An interim waiver would remain in effect until a waiver decision is published or until DOE publishes a new or amended test procedure that addresses the issues presented in the waiver, whichever is earlier.

    The proposed rule would not impose any new requirements on any manufacturers, including small businesses. The proposed rule would provide greater certainty to manufacturers applying for interim waivers that their petitions would be considered and adjudicated promptly, allowing them, upon DOE grant of an interim waiver, to distribute their Start Printed Page 18420products or equipment in commerce while the Department considered its final decision on the petition for waiver. No additional requirements with respect to the waiver application process would be imposed.

    For these reasons, DOE certifies that this proposed rule, if promulgated, would not have a significant economic impact on a substantial number of small entities, and therefore, no regulatory flexibility analysis has been prepared. DOE's certification and supporting statement of factual basis will be provided to the Chief Counsel of Advocacy of the SBA pursuant to 5 U.S.C. 605(b).

    D. Review Under the Paperwork Reduction Act

    Manufacturers of covered products and equipment must certify to DOE that their products or equipment comply with any applicable energy conservation standards. In certifying compliance, manufacturers must test their products and equipment according to the DOE test procedures, including any amendments adopted for those test procedures. DOE has established regulations for the certification and recordkeeping requirements for all covered consumer products and commercial equipment. 76 FR 12422 (March 7, 2011); 80 FR 5099 (Jan. 30, 2015). The collection-of-information requirement for the certification and recordkeeping is subject to review and approval by OMB under the Paperwork Reduction Act (PRA). This requirement has been approved by OMB under OMB control number 1910-1400. Public reporting burden for the certification is estimated to average 30 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information.

    Notwithstanding any other provision of the law, no person is required to respond to, nor shall any person be subject to a penalty for failure to comply with, a collection of information subject to the requirements of the PRA, unless that collection of information displays a currently valid OMB Control Number.

    E. Review Under the National Environmental Policy Act

    DOE has concluded that promulgation of this proposed rule falls into a class of actions that would not individually or cumulatively have a significant impact on the human environment, as determined by DOE's regulations implementing the National Environmental Policy Act of 1969 (42 U.S.C. 4321 et seq.). Specifically, this proposed rule amends existing regulations without changing the environmental effect of the regulations being amended, and, therefore, is covered under the Categorical Exclusion in paragraph A5 of appendix A to subpart D, 10 CFR part 1021. Accordingly, neither an environmental assessment nor an environmental impact statement is required.

    F. Review Under Executive Order 12988

    With respect to the review of existing regulations and the promulgation of new regulations, section 3(a) of Executive Order 12988, “Civil Justice Reform” (61 FR 4729, February 7, 1996), imposes on Federal agencies the general duty to adhere to the following requirements: (1) Eliminate drafting errors and ambiguity; (2) write regulations to minimize litigation; and (3) provide a clear legal standard for affected conduct rather than a general standard and promote simplification and burden reduction. Section 3(b)(2) of Executive Order 12988 specifically requires that Executive agencies make every reasonable effort to ensure that the regulation: (1) Clearly specifies the preemptive effect, if any, to be given to the regulation; (2) clearly specifies any effect on existing Federal law or regulation; (3) provides a clear legal standard for affected conduct while promoting simplification and burden reduction; (4) specifies the retroactive effect, if any, to be given to the regulation; (5) defines key terms; and (6) addresses other important issues affecting clarity and general draftsmanship under any guidelines issued by the Attorney General. Section 3(c) of Executive Order 12988 requires Executive agencies to review regulations in light of applicable standards in section 3(a) and section 3(b) to determine whether they are met or it is unreasonable to meet one or more of the standards. DOE has completed the required review and determined that, to the extent permitted by law, this proposed rule meets the relevant standards of Executive Order 12988.

    G. Review Under Executive Order 13132

    Executive Order 13132, “Federalism” (64 FR 43255, August 4, 1999), imposes certain requirements on agencies formulating and implementing policies or regulations that preempt State law or that have federalism implications. Agencies are required to examine the constitutional and statutory authority supporting any action that would limit the policymaking discretion of the States and carefully assess the necessity for such actions. DOE has examined this proposed rule and has determined that it would not preempt State law and would not have a substantial direct effect on the States, the relationship between the national government and the States, or the distribution of power and responsibilities among the various levels of government. No further action is required by Executive Order 13132.

    H. Review Under Executive Order 13175

    Under Executive Order 13175 (65 FR 67249, November 6, 2000) on “Consultation and Coordination with Indian Tribal Governments,” DOE may not issue a discretionary rule that has “tribal” implications and imposes substantial direct compliance costs on Indian tribal governments. DOE has determined that the proposed rule would not have such effects and concluded that Executive Order 13175 does not apply to this proposed rule.

    I. Review Under the Unfunded Mandates Reform Act of 1995

    Title II of the Unfunded Mandates Reform Act of 1995 (UMRA) requires each Federal agency to assess the effects of Federal regulatory actions on State, local, and Tribal governments and the private sector. Public Law 104-4, sec. 201 (codified at 2 U.S.C. 1531). For regulatory actions likely to result in a rule that may cause the expenditure by State, local, and Tribal governments, in the aggregate, or by the private sector of $100 million or more in any one year (adjusted annually for inflation), section 202 of UMRA requires a Federal agency to publish a written statement that estimates the resulting costs, benefits, and other effects on the national economy. (2 U.S.C. 1532(a),(b)) UMRA also requires a Federal agency to develop an effective process to permit timely input by elected officers of State, local, and Tribal governments on a “significant intergovernmental mandate,” and requires an agency plan for giving notice and opportunity for timely input to potentially affected small governments before establishing any requirements that might significantly or uniquely affect them. On March 18, 1997, DOE published a statement of policy on its process for intergovernmental consultation under UMRA. 62 FR 12820. (This policy is also available at http://energy.gov/​gc/​office-general-counsel.) DOE examined this proposed rule according to UMRA and its statement of policy and has tentatively determined that the rule contains neither an intergovernmental mandate, nor a mandate that may result in the expenditure by State, local, and Tribal government, in the aggregate, or by the private sector, of $100 million or Start Printed Page 18421more in any year. Accordingly, no further assessment or analysis is required under UMRA.

    J. Review Under Executive Order 13211

    Executive Order 13211, “Actions Concerning Regulations That Significantly Affect Energy Supply, Distribution, or Use,” 66 FR 28355 (May 22, 2001) requires Federal agencies to prepare and submit to the OMB a Statement of Energy Effects for any proposed significant energy action. A “significant energy action” is defined as any action by an agency that promulgated or is expected to lead to promulgation of a final rule, and that: (1) Is a significant regulatory action under Executive Order 12866, or any successor order; and (2) is likely to have a significant adverse effect on the supply, distribution, or use of energy, or (3) is designated by the Administrator of OIRA as a significant energy action. For any proposed significant energy action, the agency must give a detailed statement of any adverse effects on energy supply, distribution, or use should the proposal be implemented, and of reasonable alternatives to the action and their expected benefits on energy supply, distribution, and use. This regulatory action would not have a significant adverse effect on the supply, distribution, or use of energy and is therefore not a significant energy action. Accordingly, DOE has not prepared a Statement of Energy Effects.

    K. Review Under the Treasury and General Government Appropriations Act, 1999

    Section 654 of the Treasury and General Government Appropriations Act, 1999 (Pub. L. 105-277) requires Federal agencies to issue a Family Policymaking Assessment for any proposed rule that may affect family well-being. The proposed rule would not have any impact on the autonomy or integrity of the family as an institution. Accordingly, DOE has concluded that it is not necessary to prepare a Family Policymaking Assessment.

    L. Review Under the Treasury and General Government Appropriations Act, 2001

    The Treasury and General Government Appropriations Act, 2001 (44 U.S.C. 3516 note) provides for agencies to review most disseminations of information to the public under guidelines established by each agency pursuant to general guidelines issued by OMB. OMB's guidelines were published at 67 FR 8452 (February 22, 2002), and DOE's guidelines were published at 67 FR 62446 (October 7, 2002). DOE has reviewed this proposed rule under the OMB and DOE guidelines and has concluded that it is consistent with applicable policies in those guidelines.

    V. Public Participation

    A. Submission of information

    DOE will accept comments, data and information regarding this proposed rule before or after the public hearings, but no later than the date provided in the DATES section at the beginning of this proposed rule. Interested individuals are invited to participate in this proceeding by submitting data, views, or arguments with respect to this proposed rule using any of the methods described in the ADDRESSES section at the beginning of this proposed rule. To help the Department review the submitted comments, commenters are requested to reference the paragraph(s), e.g., § 835.3(a), to which they refer where possible.

    1. Submitting comments via http://www.regulations.gov. The http://www.regulations.gov web page will require you to provide your name and contact information. Your contact information will be viewable to DOE's Office of Energy Efficiency and Renewable Energy staff only. Your contact information will not be publicly viewable except for your first and last names, organization name (if any), and submitter representative name (if any). If your comment is not processed properly because of technical difficulties, DOE will use this information to contact you. If DOE cannot read your comment due to technical difficulties and cannot contact you for clarification, DOE may not be able to consider your comment. However, your contact information will be publicly viewable if you include it in the comment itself or in any documents attached to your comment. Any information that you do not want to be publicly viewable should not be included in your comment, nor in any document attached to your comment. Otherwise, persons viewing comments will see only first and last names, organization names, correspondence containing comments, and any documents submitted with the comments.

    Do not submit to http://www.regulations.gov information for which disclosure is restricted by statute, such as trade secrets and commercial or financial information (hereinafter referred to as Confidential Business Information (CBI)). Comments submitted through http://www.regulations.gov cannot be claimed as CBI. Comments received through the website will waive any CBI claims for the information submitted. For information on submitting CBI, see the “Confidential Business Information” section.

    DOE processes submissions made through http://www.regulations.gov before posting them. Normally, comments will be posted within a few days of being submitted. However, if large volumes of comments are being processed simultaneously, your comment may not be viewable for up to several weeks. Please keep the comment tracking number that http://www.regulations.gov provides after you have successfully uploaded your comment.

    2. Submitting comments via email, mail or hand delivery/courier. Comments and documents submitted via email, mail, or hand delivery/courier, also will be posted to http://www.regulations.gov. If you do not want your personal contact information to be publicly viewable, do not include it in your comment or any accompanying documents. Instead, provide your contact information in a cover letter. Include your first and last names, email address, telephone number, and optional mailing address. The cover letter will not be publicly viewable as long as it does not include any comments.

    Include contact information each time you submit comments, data, documents, and other information to DOE. If you submit via mail or hand delivery/courier, please provide all items on a CD or USB flash drive, if feasible. It is not necessary to submit printed copies. No facsimiles (faxes) will be accepted.

    Comments, data, and other information submitted to DOE electronically should be provided in PDF (preferred), Microsoft Word or Excel, WordPerfect, or text (ASCII) file format. Provide documents that are not secured, that are written in English, and that are free of any defects or viruses. Documents should not contain special characters or any form of encryption and, if possible, they should carry the electronic signature of the author.

    3. Confidential Business Information. Pursuant to the provisions of 10 CFR 1004.11, anyone submitting information or data he or she believes to be confidential and exempt by law from public disclosure should submit via email, postal mail two well-marked copies: one copy of the document marked “CONFIDENTIAL BUSINESS INFORMATION” including all the information believed to be confidential, and one copy of the document marked “NO CONFIDENTIAL BUSINESS Start Printed Page 18422INFORMATION” with the information believed to be confidential deleted. Submit these documents via email or CD, if feasible. DOE will make its own determination as to the confidentiality of the information and treat it accordingly. Factors of interest to DOE when evaluating requests to treat submitted information as confidential include: (1) A description of the items; (2) whether and why such items are customarily treated as confidential within the industry; (3) whether the information is generally known by or available from other sources; (4) whether the information has previously been made available to others without obligation concerning its confidentiality; (5) an explanation of the competitive injury to the submitting person which would result from public disclosure; (6) when such information might lose its confidential character due to the passage of time; and (7) why disclosure of the information would be contrary to the public interest.

    It is DOE's policy that all comments may be included in the public docket, without change and as received, including any personal information provided in the comments (except information deemed to be exempt from public disclosure).

    4. Campaign form letters. Please submit campaign form letters by the originating organization in batches of between 50 to 500 form letters per PDF or as one form letter with a list of supporters' names compiled into one or more PDFs. This reduces comment processing and posting time.

    B. Issues on Which DOE Seeks Information

    1. DOE requests comment on the length of time manufacturers have previously waited for DOE to provide notification of the disposition of applications for interim waiver (or final decisions on waiver petitions), and the correlated extent of cost savings and any other benefits they expect to realize as a result of the proposal to specify in the regulations that if the Department fails to issue an interim waiver decision within 30 business days following receipt of an application, the application is deemed granted. DOE also requests comment on its proposal to specify that an interim waiver would remain in effect until the earlier of the following: a waiver decision is published or DOE publishes a new or amended test procedure that addresses the issues presented in the waiver.

    VI. Approval of the Office of the Secretary

    The Secretary of Energy has approved publication of this proposed rule.

    Start List of Subjects

    List of Subjects

    10 CFR Part 430

    • Administrative practice and procedure
    • Confidential business information
    • Energy conservation
    • Household appliances
    • Imports
    • Incorporation by Reference
    • Intergovernmental relations
    • Small businesses

    10 CFR Part 431

    • Administrative practice and procedure
    • Confidential business information
    • Test procedures
    • Incorporation by reference
    • Reporting and recordkeeping requirements
    End List of Subjects Start Signature

    Signed in Washington, DC, on April 24, 2019.

    Daniel R. Simmons,

    Assistant Secretary, Energy Efficiency and Renewable Energy.

    End Signature

    For the reasons set forth in the preamble, the Department of Energy proposes to amend parts 430 and 431 of Chapter II, Subchapter D, of Title 10 of the Code of Federal Regulations, as set forth below:

    Start Part

    PART 430—ENERGY CONSERVATION PROGRAM FOR CONSUMER PRODUCTS

    End Part Start Amendment Part

    1. The authority citation for part 430 continues to read as follows:

    End Amendment Part Start Authority

    Authority: 42 U.S.C. 6291-6309; 28 U.S.C. 2461 note.

    End Authority Start Amendment Part

    2. Section 430.27 is amended by revising paragraphs (e)(1) and (h)(1) to read as follows:

    End Amendment Part
    Petitions for waiver and interim waiver.
    * * * * *

    (e) Provisions specific to interim waivers—(1) Disposition of application. (i) DOE will notify the applicant in writing of the disposition of the petition for interim waiver within 30 days of receipt of the application. If DOE does not notify the applicant in writing of the disposition of the petition for interim waiver within 30 business days of receipt of the application, the interim waiver, as requested in the application, is deemed granted. Notice of DOE's determination on the petition for interim waiver will be published in the Federal Register.

    (ii) A waiver is considered received on the date it is received by the Department through the Department's established email box for receipt of waiver or, if delivered by mail, on the date the waiver is stamped as received by the Department.

    (iii) If DOE ultimately denies the petition for waiver or grants the petition with a different alternate test procedure than specified in the interim waiver, DOE will provide a grace period of 180 days for the manufacturer to begin to use the DOE test procedure or the alternate test procedure specified in the decision and order on the petition to make representations of energy efficiency.

    * * * * *

    (h) Duration. (1) Interim waivers remain in effect until the earlier of the following:

    (i) DOE publishes a decision on a petition for waiver in the Federal Register pursuant to paragraph (f) of this section; or

    (ii) DOE publishes in the Federal Register a new or amended test procedure that addresses the issues presented in the waiver.

    * * * * *
    Start Part

    PART 431—ENERGY EFFICIENCY PROGRAM FOR CERTAIN COMMERCIAL AND INDUSTRIAL EQUIPMENT

    End Part Start Amendment Part

    3. The authority citation for part 431 continues to read as follows:

    End Amendment Part Start Authority

    Authority: 42 U.S.C. 6291-6317; 28 U.S.C. 2461 note.

    End Authority Start Amendment Part

    4. Section 431.401 is amended by revising paragraphs (e)(1) and (h)(1) to read as follows:

    End Amendment Part
    Petitions for waiver and interim waiver.
    * * * * *

    (e) Provisions specific to interim waivers—(1) Disposition of application. (i) DOE will notify the applicant in writing of the disposition of the petition for interim waiver within 30 business days of receipt of the application. If DOE does not notify the applicant in writing of the disposition of the petition for interim waiver within 30 business days of receipt of the application, the interim waiver, as requested in the application, is deemed granted. Notice of DOE's determination on the petition for interim waiver will be published in the Federal Register.

    (ii) A waiver is considered received on the date it is received by the Department through the Department's established email box for receipt of waiver or, if delivered by mail, on the date the waiver is stamped as received by the Department.

    (iii) If DOE ultimately denies the petition for waiver or grants the petition with a different alternate test procedure than specified in the interim waiver, Start Printed Page 18423DOE will provide a grace period of 180 days for the manufacturer to begin to use the DOE test procedure or the alternate test procedure specified in the decision and order on the petition to make representations of energy efficiency.

    * * * * *

    (h) Duration. (1) Interim waivers remain in effect until the earlier of the following:

    (i) DOE publishes a decision on a petition for waiver pursuant to paragraph (f) of this section in the Federal Register; or

    (ii) DOE publishes in the Federal Register a new or amended test procedure that addresses the issues presented in the waiver.

    * * * * *
    End Supplemental Information

    Footnotes

    1.  All references to EPCA in this document refer to the statute as amended through the Energy Efficiency Improvement Act of 2015, Public Law 114-11 (April 30, 2015).

    Back to Citation

    2.  For editorial reasons, Part B was redesignated as Part A upon codification in the U.S. Code.

    Back to Citation

    3.  For editorial reasons, Part C was redesignated as Part A-1 upon codification in the U.S. Code.

    Back to Citation

    5.  DOE notes that granting an interim waiver application, as proposed, is not a final agency action as contemplated by the Administrative Procedure Act (APA). The APA defines an “agency action” as including “the whole or a part of an agency rule, order, license, sanction, relief, or the equivalent or denial thereof, or failure to act.” 5 U.S.C. 551(13). The Supreme Court has explained that to be “final,” an agency action must “mark the consummation of the agency's decision making process, and must either determine rights or obligations or occasion legal consequences.” Alaska Dep't of Envtl. Conservation v. EPA, 540 U.S. 461, 482 (2004) (quotation omitted); see Bennett v. Spear, 520 U.S. 154, 178 (1997). In this case, interim waivers do not represent the consummation of the Department's decision making process. Indeed, while manufacturers would be able to test and distribute their products or equipment in commerce if granted an interim waiver under the proposal, DOE regulations still contemplate issuance of a final decision on the associated petition for waiver, or a final rule amending the test procedure. Either of these actions could have rights or obligations, or consequences, that differ from those provided temporarily under an interim waiver.

    Back to Citation

    6.  In 2016, five of the applications for waiver, four of which included a request for an interim waiver, were addressed in a single final rule amending the test procedures for central air conditioners and heat pumps (81 FR 36991). DOE did not act on the four requests for interim waiver, and there is no accompanying data on the time lag associated with these interim waiver requests.

    Back to Citation

    7.  Fifty percent of the requests for interim waiver received in 2018 were still pending resolution as of this writing; as a result, totals for 2018 will continue to increase until these requests are concluded.

    Back to Citation

    8.  2018 data is omitted here as only one decision and order has yet been issued for waivers requested in 2018 and all remaining requests are still pending. Multiple requests for waiver received in 2017 were also still pending as of this writing; as a result, totals for 2017 and 2018 will continue to increase until these requests are concluded.

    Back to Citation

    9.  “The 7 percent rate is an estimate of the average before-tax rate of return to private capital in the U.S. economy. It is a broad measure that reflects the returns to real estate and small business capital as well as corporate capital.” https://www.whitehouse.gov/​sites/​whitehouse.gov/​files/​omb/​circulars/​A4/​a-4.pdf.

    Back to Citation

    11.  Walk-in Coolers and Freezers (WICF) are counted as a single affected product. However, Table IV.B.1. breaks out which petitions concerned which WICF components, as their annual shipments and prices vary accordingly.

    Back to Citation

    12.  Average price is generally the base case average MSP of equipment from the life-cycle cost year in the most recently published technical support document. This represents a shipment-weighted average across efficiency distribution and across all product classes.

    Back to Citation

    [FR Doc. 2019-08699 Filed 4-30-19; 8:45 am]

    BILLING CODE 6450-01-P

Document Information

Published:
05/01/2019
Department:
Energy Department
Entry Type:
Proposed Rule
Action:
Notice of proposed rulemaking; request for comment.
Document Number:
2019-08699
Dates:
The comment period for this proposed rule will end on July 1, 2019.
Pages:
18414-18423 (10 pages)
Docket Numbers:
EERE-2019-BT-NOA-0011
RINs:
1904-AE24: Test Procedure Interim Waiver Process
RIN Links:
https://www.federalregister.gov/regulations/1904-AE24/test-procedure-interim-waiver-process
Topics:
Administrative practice and procedure, Confidential business information, Energy conservation, Household appliances, Imports, Incorporation by reference, Incorporation by reference, Intergovernmental relations, Reporting and recordkeeping requirements, Small businesses
PDF File:
2019-08699.Pdf
Supporting Documents:
» 2021-12-14 Test Procedure Interim Waiver Process; Final rule.
» 2021-08-20 Test Procedure Interim Waiver Process; Notice of proposed rulemaking and request for comment
» Documentation of Changes between the draft Final Rule submitted to the Office of Information and Regulatory Affairs (OIRA) and the issued Final Rule
» 2020-12-11 Test Procedure Interim Waiver Process; Final rule
» 2019-07-11 Transcript: Webinar Test Procedure Interim Waiver Process U.S. Dept. of Energy
» 2019-07-22 Test Procedure Interim Waiver Process; Proposed rule; re-opening of public comment period
» DOE notes of teleconference between DOE and representative of SBA Office of Advocacy
» DOE Test Procedure Waiver PR Roundtable Attendees 6.26.19
» Frequently Asked Questions - Notice of Proposed Rulemaking pertaining to the Test Procedure Interim Waiver Process
» 2019-06-26 Test Procedure Interim Waiver Process; Notice of webinar and extension of public comment period
CFR: (2)
10 CFR 430.27
10 CFR 431.401