[Federal Register Volume 63, Number 90 (Monday, May 11, 1998)]
[Notices]
[Pages 25895-25896]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 98-12439]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
National Highway Traffic Safety Administration
[Docket No. NHTSA-98-3806]
Notice of Receipt of Petition for Decision That Nonconforming
1995 Ferrari 456 Passenger Cars Are Eligible for Importation
AGENCY: National Highway Traffic Safety Administration, DOT.
ACTION: Notice of receipt of petition for decision that nonconforming
1995 Ferrari 456 passenger cars are eligible for importation.
-----------------------------------------------------------------------
SUMMARY: This notice announces receipt by the National Highway Traffic
Safety Administration (NHTSA) of a petition for a decision that a 1995
Ferrari 456 that was not originally manufactured to comply with all
applicable Federal motor vehicle safety standards is eligible for
importation into the United States because (1) it is substantially
similar to a vehicle that was originally manufactured for importation
into and sale in the United States and that was certified by its
manufacturer as complying with the safety standards, and (2) it is
capable of being readily altered to conform to the standards.
DATE: The closing date for comments on the petition is June 10, 1998.
ADDRESS: Comments should refer to the docket number and notice number,
and be submitted to: Docket Management, Room PL-401, 400 Seventh St.,
SW, Washington, DC 20590. [Docket hours are from 10 am to 5 pm]
FOR FURTHER INFORMATION CONTACT: George Entwistle, Office of Vehicle
Safety Compliance, NHTSA (202-366-5306).
SUPPLEMENTARY INFORMATION:
Background
Under 49 U.S.C. 30141(a)(1)(A), a motor vehicle that was not
originally manufactured to conform to all applicable Federal motor
vehicle safety standards shall be refused admission into the United
States unless NHTSA has decided that the motor vehicle is substantially
similar to a motor vehicle originally manufactured for importation into
and sale in the United States, certified under 49 U.S.C. 30115, and of
the same model year as the model of the motor vehicle to be compared,
and is capable of being readily altered to conform to all applicable
Federal motor vehicle safety standards.
Petitions for eligibility decisions may be submitted by either
manufacturers or importers who have registered with NHTSA pursuant to
49 CFR part 592. As specified in 49 CFR 593.7, NHTSA publishes notice
in the Federal Register of each petition that it receives, and affords
interested persons an opportunity to comment on the petition. At the
close of the comment period, NHTSA decides, on the basis of the
petition and any comments that it has received, whether the vehicle is
eligible for importation. The agency then publishes this decision in
the Federal Register.
J.K. Motors of Kingsville, Maryland (``J.K.'') (Registered Importer
90-006) has petitioned NHTSA to decide whether 1995 Ferrari 456
passenger cars are eligible for importation into the United States. The
vehicle which J.K. believes is substantially similar is the 1995
Ferrari 456 that was manufactured for importation into, and sale in,
the United States and certified by its manufacturer as conforming to
all applicable Federal motor vehicle safety standards.
[[Page 25896]]
The petitioner claims that it carefully compared the non-U.S.
certified 1995 Ferrari 456 to its U.S. certified counterpart, and found
the two vehicles to be substantially similar with respect to compliance
with most Federal motor vehicle safety standards.
J.K. submitted information with its petition intended to
demonstrate that the non-U.S. certified 1995 Ferrari 456, as originally
manufactured, conforms to many Federal motor vehicle safety standards
in the same manner as its U.S. certified counterpart, or is capable of
being readily altered to conform to those standards.
Specifically, the petitioner claims that the non-U.S. certified
1995 Ferrari 456 is identical to its U.S. certified counterpart with
respect to compliance with Standards Nos. 102 Transmission Shift Lever
Sequence * * *, 103 Defrosting and Defogging Systems, 104 Windshield
Wiping and Washing Systems, 105 Hydraulic Brake Systems, 106 Brake
Hoses, 109 New Pneumatic Tires, 113 Hood Latch Systems, 116 Brake
Fluid, 124 Accelerator Control Systems, 201 Occupant Protection in
Interior Impact, 202 Head Restraints, 204 Steering Control Rearward
Displacement, 205 Glazing Materials, 206 Door Locks and Door Retention
Components, 207 Seating Systems, 209 Seat Belt Assemblies, 210 Seat
Belt Assembly Anchorages, 212 Windshield Retention, 216 Roof Crush
Resistance, 219 Windshield Zone Intrusion, 301 Fuel System Integrity,
and 302 Flammability of Interior Materials.
Petitioner also contends that the vehicle is capable of being
readily altered to meet the following standards, in the manner
indicated:
Standard No. 101 Controls and Displays: (a) inscription of the word
``Brake'' on the dash, in place of the international ECE warning
symbol; (b) replacement of the speedometer/odometer with one calibrated
in miles per hour.
Standard No. 108 Lamps, Reflective Devices and Associated
Equipment: (a) installation of U.S.-model headlamps and front
sidemarker lights; (b) installation of U.S.-model taillamp assemblies
and rear sidemarker lights; (c) installation of a U.S.-model high-
mounted stop light assembly.
Standard No. 110 Tire Selection and Rims: installation of a tire
information placard.
Standard No. 111 Rearview Mirror: replacement of the passenger side
rearview mirror with a U.S.-model component.
Standard No. 114 Theft Protection: installation of a key
microswitch and a warning buzzer.
Standard No. 118 Power Window Systems: installation of a relay in
the power window system so that the window transport is inoperative
when the ignition is switched off.
Standard No. 208 Occupant Crash Protection: (a) installation of a
seat belt warning buzzer wired to the seat belt latch; (b) replacement
of the seat belts and the driver's and passenger's side air bags, knee
bolsters, control unit and sensors with U.S.-model components on
vehicles that are not so equipped. The petitioner states that the
vehicle is equipped with combination lap and shoulder restraints are
automatic, self-tensioning, and that release by means of a single red
push button at both front and rear outboard designated seating
positions.
Standard No. 214 Side Impact Protection: installation of door bars
on vehicles that are not so equipped.
With regard to compliance with the Bumper Standard found in 49 CFR
Part 581, the petitioner states that the bumpers and the support
structure for the bumpers on the non-U.S. certified 1995 Ferrari 456
are identical to those found on the vehicle's U.S. certified
counterpart. The petitioner notes, however, that some of these bumpers
may have to be replaced if they do not have holes cut into the side to
accommodate side marker lights.
The petitioner also states that a vehicle identification number
plate must be affixed to the vehicle to meet the requirements of 49 CFR
part 565.
Interested persons are invited to submit comments on the petition
described above. Comments should refer to the docket number and be
submitted to: Docket Section, National Highway Traffic Safety
Administration, Room 5109, 400 Seventh Street, S.W., Washington, DC
20590. It is requested but not required that 10 copies be submitted.
All comments received before the close of business on the closing
date indicated above will be considered, and will be available for
examination in the docket at the above address both before and after
that date. To the extent possible, comments filed after the closing
date will also be considered. Notice of final action on the petition
will be published in the Federal Register pursuant to the authority
indicated below.
Authority: 49 U.S.C. 30141(a)(1)(A) and (b)(1); 49 CFR 593.8;
delegations of authority at 49 CFR 1.50 and 501.8.
Issued on: May 6, 1998.
Marilynne Jacobs,
Director, Office of Vehicle Safety Compliance.
[FR Doc. 98-12439 Filed 5-8-98; 8:45 am]
BILLING CODE 4910-59-P
