2023-13011. Airworthiness Directives; Airbus SAS Airplanes

AGENCY:

Federal Aviation Administration (FAA), DOT.

ACTION:

Notice of proposed rulemaking (NPRM).

SUMMARY:

The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus SAS Model A330–200 series; A330–200 Freighter series; A330–300 series; A330–800 series; A330–900 series; A340–200 series; and A340–300 series airplanes. This proposed AD was prompted by reports of cracks found in the scroll housing assembly of Honeywell GTCP331–350 auxiliary power units (APUs). This proposed AD would require replacing each affected APU or re-identifying certain APU scroll housing assemblies, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). This proposed AD would also prohibit the installation of affected parts under certain conditions. The FAA is proposing this AD to address the unsafe condition on these products.

DATES:

The FAA must receive comments on this proposed AD by August 4, 2023.

ADDRESSES:

You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods:

• Federal eRulemaking Portal: Go to regulations.gov. Follow the instructions for submitting comments.

• Fax: [phone].

• Mail: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE, Washington, DC 20590.

• Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

AD Docket: You may examine the AD docket at regulations.gov under Docket No. FAA–2023–1217; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, the mandatory continuing airworthiness information (MCAI), any comments received, and other information. The street address for Docket Operations is listed above.

Material Incorporated by Reference:

• For EASA material that is proposed for IBR in this NPRM, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone [phone]; email [e-mail]; website easa.europa.eu. You may find this material on the EASA website at ad.easa.europa.eu. It is also available at regulations.gov under Docket No. FAA–2023–1217.

• For Honeywell service information identified in this NPRM, contact Honeywell International, Inc., 111 South 34th Street, Phoenix, AZ 85034; phone: [phone]; fax: [phone]; website: myaerospace.honeywell.com/wps/portal.

• You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195.

FOR FURTHER INFORMATION CONTACT:

Timothy Dowling, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone [phone]; email [e-mail].

SUPPLEMENTARY INFORMATION:

Comments Invited

The FAA invites you to send any written relevant data, views, or arguments about this proposal. Send your comments to an address listed under ADDRESSES . Include “Docket No. FAA–2023–1217; Project Identifier MCAI–2023–00477–T” at the beginning of your comments. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. The FAA will consider all comments received by the closing date and may amend this proposal because of those comments.

Except for Confidential Business Information (CBI) as described in the following paragraph, and other information as described in 14 CFR 11.35, the FAA will post all comments received, without change, to regulations.gov, including any personal information you provide. The agency will also post a report summarizing each substantive verbal contact received about this NPRM.

Confidential Business Information

CBI is commercial or financial information that is both customarily and actually treated as private by its owner. Under the Freedom of Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public disclosure. If your comments responsive to this NPRM contain commercial or financial information that is customarily treated as private, that you actually treat as private, and that is relevant or responsive to this NPRM, it is important that you clearly designate the submitted comments as CBI. Please mark each page of your submission containing CBI as “PROPIN.” The FAA will treat such marked submissions as confidential under the FOIA, and they will not be placed in the public docket of this NPRM. Submissions containing CBI should be sent to Timothy Dowling, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone [phone]; email [e-mail]. Any commentary that the FAA receives which is not specifically designated as CBI will be placed in the public docket for this rulemaking.

Background

EASA, which is the Technical Agent for the Member States of the European Union, has issued EASA AD 2023–0056, dated March 16, 2023 (EASA AD 2023–0056) (also referred to as the MCAI), to correct an unsafe condition for all Airbus SAS Model 330–201, –202, –203, –223, –223F, –243, –243F, –301, –302, –303, –321, –322, –323, –341, –342, –343, –841, –941, and –743L airplanes, and Model A340–211, –212, –213, –311, –312, and –313 airplanes. Model A330–743L airplanes are not certificated by the FAA and are not included on the U.S. type certificate data sheet; this proposed AD therefore does not include those airplanes in the applicability. The MCAI states that cracks were found in the scroll housing assembly of Honeywell GTCP331–350 APUs. This condition, if not addressed, could lead to hot air leakage and consequent damage to the APU compartment and loss of the APU doors, possibly resulting in damage to the airplane.

The FAA is proposing this AD to address the unsafe condition on these products.

You may examine the MCAI in the AD docket at regulations.gov under Docket No. FAA–2023–1217.

Related Service Information Under 1 CFR Part 51

EASA AD 2023–0056 specifies procedures for replacing each affected APU or re-identifying certain APU scroll housing assemblies (those having part number (P/N) 5053–181–001–501 or P/N 0331207990 and `SR–1' next to the part number marking). EASA AD 2023–0056 also prohibit the installation of affected parts under certain conditions.

Honeywell Service Bulletin 5053–181–49–7895, dated July 21, 2006, specifies procedures for, among other actions, re-identifying affected APU scroll housing assemblies. While Honeywell distributes this document, Aeronamic develops the technical content.

This material is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in ADDRESSES .

FAA's Determination

This product has been approved by the aviation authority of another country and is approved for operation in the United States. Pursuant to the FAA's bilateral agreement with this State of Design Authority, it has notified the FAA of the unsafe condition described in the MCAI and service information referenced above. The FAA is issuing this NPRM after determining that the unsafe condition described previously is likely to exist or develop in other products of the same type design.

Proposed AD Requirements in This NPRM

This proposed AD would require accomplishing the actions specified in EASA AD 2023–0056 described previously, except for any differences identified as exceptions in the regulatory text of this proposed AD.

Explanation of Required Compliance Information

In the FAA's ongoing efforts to improve the efficiency of the AD process, the FAA developed a process to use some civil aviation authority (CAA) ADs as the primary source of information for compliance with requirements for corresponding FAA ADs. The FAA has been coordinating this process with manufacturers and CAAs. As a result, the FAA proposes to incorporate EASA AD 2023–0056 by reference in the FAA final rule. This proposed AD would, therefore, require compliance with EASA AD 2023–0056 in its entirety through that incorporation, except for any differences identified as exceptions in the regulatory text of this proposed AD. Using common terms that are the same as the heading of a particular section in EASA AD 2023–0056 does not mean that operators need comply only with that section. For example, where the AD requirement refers to “all required actions and compliance times,” compliance with this AD requirement is not limited to the section titled “Required Action(s) and Compliance Time(s)” in EASA AD 2023–0056. Service information required by EASA AD 2023–0056 for compliance will be available at regulations.gov under Docket No. FAA–2023–1217 after the FAA final rule is published.

Costs of Compliance

The FAA estimates that this AD, if adopted as proposed, would affect 128 airplanes of U.S. registry. The FAA estimates the following costs to comply with this proposed AD:

Estimated Costs for Required Actions

Labor cost	Parts cost	Cost per product	Cost on U.S. operators
Up to 18 work-hours × $85 per hour = $1,530 (replace APU)	$1,612,820	Up to $1,614,350	(*)
Up to 20 work-hours × $85 per hour = $1,700 (re-identify APU scroll housing assembly)	3,141	Up to $4,841	(*)
* Operators have the option to replace the APU or re-identify the APU scroll housing assembly. Replacement or re-identification is only required if an affected part is installed on an airplane. The FAA has no way of knowing how many affected parts are installed on U.S.-registered airplanes or which option an operator will choose for a given airplane with an affected part. Therefore, the FAA has no definitive data on which to provide a fleet cost estimate for the required actions specified in this proposed AD.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority.

The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

The FAA determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed regulation:

(1) Is not a “significant regulatory action” under Executive Order 12866,

(2) Would not affect intrastate aviation in Alaska, and

(3) Would not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

• Air transportation
• Aircraft
• Aviation safety
• Incorporation by reference
• Safety

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39—AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13

[Amended]

2. The FAA amends § 39.13 by adding the following new airworthiness directive:

Airbus SAS: Docket No. FAA–2023–1217; Project Identifier MCAI–2023–00477–T.

(a) Comments Due Date

The FAA must receive comments on this airworthiness directive (AD) by August 4, 2023.

(b) Affected ADs

None.

(c) Applicability

This AD applies to all Airbus SAS airplanes specified in paragraphs (c)(1) through (7) of this AD, certificated in any category.

(1) Model A330–201, –202, –203, –223, and –243 airplanes.

(2) Model A330–223F and –243F airplanes.

(3) Model A330–301, –302, –303, –321, –322, –323, –341, –342, and –343 airplanes.

(4) Model A330–841 airplanes.

(5) Model A330–941 airplanes.

(6) Model A340–211, –212, and –213 airplanes.

(7) Model A340–311, –312, and –313 airplanes.

(d) Subject

Air Transport Association (ATA) of America Code 49, Airborne auxiliary power.

(e) Unsafe Condition

This AD was prompted by reports of cracks found in the scroll housing assembly of Honeywell GTCP331–350 auxiliary power units (APUs). The FAA is issuing this AD to address such cracks. The unsafe condition, if not addressed, could result in hot air leakage and consequent damage to the APU compartment and loss of the APU doors, possibly resulting in damage to the airplane.

(f) Compliance

Comply with this AD within the compliance times specified, unless already done.

(g) Requirements

Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2023–0056, dated March 16, 2023 (EASA AD 2023–0056).

(h) Exceptions to EASA AD 2023–0056

(1) Where EASA AD 2023–0056 refers to its effective date, this AD requires using the effective date of this AD.

(2) This AD does not adopt the “Remarks” section of EASA AD 2023–0056.

(3) Where EASA AD 2023–0056 specifies to re-identify an SR–1 affected part “in accordance with the instructions of the SB,” for this AD, operators must use Honeywell Service Bulletin 5053–181–49–7895, dated July 21, 2006.

Note 1 to paragraph (h)(3): Honeywell distributes this document; Aeronamic develops the technical content.

(i) Additional AD Provisions

The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs): The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the International Validation Branch, send it to the attention of the person identified in paragraph (j) of this AD. Information may be emailed to: [e-mail]. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.

(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.

(3) Required for Compliance (RC): Except as required by paragraph (i)(2) of this AD, if any service information contains procedures or tests that are identified as RC, those procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC.

(j) Additional Information

For more information about this AD, contact Timothy Dowling, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone [phone]; email [e-mail].

(k) Material Incorporated by Reference

(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.

(2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise.

(i) European Union Aviation Safety Agency (EASA) AD 2023–0056, dated March 16, 2023.

(ii) Honeywell Service Bulletin 5053–181–49–7895, dated July 21, 2006.

Note 2 to paragraph (k)(2)(ii): Honeywell distributes this document; Aeronamic develops the technical content.

(3) For EASA AD 2023–0056, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone [phone]; email [e-mail]; website easa.europa.eu. You may find this EASA AD on the EASA website at ad.easa.europa.eu.

(4) For Honeywell service information identified in this AD, contact Honeywell service information identified in this AD, contact Honeywell International, Inc., 111 South 34th Street, Phoenix, AZ 85034; phone: [phone]; fax: [phone]; website: myaerospace.honeywell.com/wps/portal.

(5) You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206–231–3195.

(6) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email [e-mail], or go to: www.archives.gov/​federal-register/​cfr/​ibr-locations.html.

Issued on June 13, 2023.

Michael Linegang,

Acting Director, Compliance & Airworthiness Division, Aircraft Certification Service.