[Federal Register Volume 60, Number 138 (Wednesday, July 19, 1995)]
[Rules and Regulations]
[Pages 36969-36971]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 95-17588]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
14 CFR Part 25
[Docket No. NM-114; Special Conditions No. 25-ANM-102]
Special Conditions: Modified McDonnell Douglas Corporation Model
DC-10-30 and DC-10-40 Airplane; High Intensity Radiated Fields (HIRF)
AGENCY: Federal Aviation Administration, DOT.
ACTION: Final special conditions; request for comments.
-----------------------------------------------------------------------
SUMMARY: These special conditions are issued for the McDonnell Douglas
Corporation Model DC-10-30 and DC-10-40 modified by B & D Instruments &
Avionics, Inc., of Valley Center, Kansas. This airplane will be
equipped with a Flat Panel Engine Instrument Display that will perform
critical functions. The applicable regulations do not contain adequate
or appropriate safety standards for the protection of the Flat Panel
Engine Instrument Display from the effects of high-intensity radiated
fields (HIRF). These special conditions provide the additional safety
standards that the Administrator considers necessary to ensure that the
critical functions performed by this system are maintained when the
airplane is exposed to HIRF.
DATES: The effective date of these special conditions is June 29, 1995.
Comments must be received on or before September 5, 1995.
ADDRESSES: Comments on these final special conditions, request for
comments, may be mailed in duplicate to: Federal Aviation
Administration, Office of the Assistant Chief Counsel, Attn: Rules
Docket (ANM-7), Docket No. NM-114, 1601 Lind Avenue SW., Renton,
Washington, 98055-4056; or delivered in duplicate to the Office of the
Assistant Chief Counsel at the above address. Comments must be marked
``Docket No. NM-114.'' Comments may be inspected in the Rules Docket
weekdays, except Federal holidays, between 7:30 a.m. and 4 p.m.
FOR FURTHER INFORMATION CONTACT:
Mark Quam, FAA, Standardization Branch, Transport Airplane Directorate,
Aircraft Certification Service, 1601 Lind Avenue SW., Renton,
Washington 98055-4056; telephone (206) 227-2145.
[[Page 36970]]
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA has determined that good cause exists for making these
special conditions effective upon issuance; however, interested persons
are invited to submit such written data, views, or arguments as they
may desire. Communications should identify the regulatory docket and
special conditions number and be submitted in duplicate to the address
specified above. All communications received on or before the closing
date for comments will be considered by the Administrator. These
special conditions may be changed in light of the comments received.
All comments submitted will be available in the Rules Docket for
examination by interested persons, both before and after the closing
date for comments. A report summarizing each substantive public contact
with FAA personnel concerning this rulemaking will be filed in the
docket. Persons wishing the FAA to acknowledge receipt of their
comments submitted in response to this request must submit with those
comments a self-addressed, stamped postcard on which the following
statement is made: ``Comments to Docket No. NM-114.'' The postcard will
be date stamped and returned to the commenter.
Background
On April 7, 1995, B & D Instruments & Avionics, Inc., of Valley
Center, Kansas, applied for a supplemental type certificate to replace
the existing engine instruments (EPR, FF, N1, N2, EGT) with a Flat
Panel Display System in the McDonnell Douglas Corporation Model DC-10-
30 and DC-10-40. The Model DC-10-30 is a passenger transport category
airplane, and is capable of operating to an altitude of 42,000 feet.
For all flights, 3 persons (pilot, copilot, flight engineer) are
required. The original equipment installed in these airplanes presented
the required engine information in the form of analog displays. The
proposed modification would replace the existing engine instruments
(EPR, FF, N1, N2, EGT) with a digital Flat Panel Engine Instrument
Display System. The installation of the Flat Panel Engine Instrument
Display System is potentially vulnerable to high-intensity radiated
fields (HIRF) external to the airplane.
Supplemental Type Certification Basis
Under the provisions of Sec. 21.101 of the Federal Aviation
Regulations (FAR), B & D Instruments & Avionics, Inc, must show that
the altered McDonnell Douglas Corporation Model DC-10-30 and DC-10-40
airplanes continue to meet the applicable provisions of the regulations
incorporated by reference in Type Certificate No. A22WE, or the
applicable regulations in effect on the date of application for the
change. The regulations incorporated by reference in the type
certificate are commonly referred to as the ``original type
certification basis.''
The regulations incorporated by reference in Type Certificate No.
A22WE include the following for the McDonnell Douglas Corporation Model
DC-10-30 and DC-10-40 airplanes:
Part 25 of the FAR effective February 1, 1965, Amendments 25-1
through 25-22.
In addition, under Sec. 21.101(b)(1), the following sections of the
FAR apply to the Flat Panel Engine Instrument Display installation:
Secs. 25.1301(d), 25.1305 and 25.1322, as amended by Amendment 25-38;
and Secs. 25.1309, 25.1321 (a), (c), (d), and (e), 25.1331, 25.1337, as
amended by Amendment 25-40. These special conditions form an additional
part of the supplemental type certification basis.
If the Administrator finds that the applicable airworthiness
regulations (i.e., part 25, as amended) do not contain adequate or
appropriate safety standards for the McDonnell Douglas Corporation
Model DC-10-30 and DC-10-40 airplanes because of a novel or unusual
design feature, special conditions are prescribed under the provisions
of Sec. 21.16 to establish a level of safety equivalent to that
established in the regulations.
Special conditions, as appropriate, are issued in accordance with
Sec. 11.49 of the FAR after public notice, as required by Secs. 11.28
and 11.29, and become part of the type certification basis in
accordance with Sec. 21.101(b)(2).
Special conditions are initially applicable to the model for which
they are issued. Should the applicant apply for a supplemental type
certificate to modify any other model included on the same type
certificate to incorporate the same novel or unusual design feature,
the special conditions would also apply to the other model under the
provisions of Sec. 21.101(a)(1).
Discussion
There is no specific regulation that addresses protection
requirements for electrical and electronic systems from high-intensity
radiated fields (HIRF). Increased power levels from ground-based radio
transmitters, and the growing use of sensitive electrical and
electronic systems to command and control airplanes, have made it
necessary to provide adequate protection.
To ensure that a level of safety is achieved equivalent to that
intended by the regulations incorporated by reference, special
conditions are needed for the modified Boeing Model DC-10-30 and DC-10-
40 airplanes that would require that the Flat Panel Engine Instrument
Display System be designed and installed to preclude component damage
and interruption of function due to the effects of HIRF.
High-Intensity Radiated Fields (HIRF)
With the trend toward increased power levels from ground-based
transmitters, plus the advent of space and satellite communications,
coupled with electronic command and control of the airplane, the
immunity of critical digital avionics systems, such as the Flat Panel
Engine Instrument Display System, to HIRF must be established.
It is not possible to precisely define the HIRF to which the
airplanes will be exposed in service. There is also uncertainty
concerning the effectiveness of airframe shielding for HIRF.
Furthermore, coupling of electromagnetic energy to cockpit-installed
equipment through the cockpit window apertures is undefined. Based on
surveys and analysis of existing HIRF emitters, an adequate level of
protection exists when compliance with the HIRF protection special
condition is shown with either paragraphs 1 or 2 below:
1. A minimum threat of 100 volts per meter peak electric field
strength from 10 KHz to 18 GHz.
a. The threat must be applied to the system elements and their
associated wiring harnesses without the benefit of airframe shielding.
b. Demonstration of this level of protection is established through
system tests and analysis.
2. A threat external to the airframe of the following field
strengths for the frequency ranges indicated:
------------------------------------------------------------------------
Peak (V/ Average
Frequency M) (V/M)
------------------------------------------------------------------------
10 KHz-100 KHz...................................... 50 50
100 KHz-500 KHz..................................... 60 60
500 KHz-2000 KHz.................................... 70 70
2 MHz-30 MHz........................................ 200 200
30 MHz-100 MHz...................................... 30 30
100 MHz-200 MHz..................................... 150 33
200 MHz-400 MHz..................................... 70 70
400 MHz-700 MHz..................................... 4,020 935
700 MHz-1000 MHz.................................... 1,700 170
1 GHz-2 GHz......................................... 5,000 990
2 GHz-4 GHz......................................... 6,680 840
4 GHz-6 GHz......................................... 6,850 310
6 GHz-8 GHz......................................... 3,600 670
8 GHz-12 GHz........................................ 3,500 1,270
[[Page 36971]]
12 GHz-18 GHz....................................... 3,500 360
18 GHz-40 GHz....................................... 2,100 750
------------------------------------------------------------------------
As discussed above, these special conditions are applicable to the
McDonnell Douglas Corporation Model DC-10-30 and DC-10-40 airplanes,
modified by B & D Instruments & Avionics, Inc. Should B & D Instruments
& Avionics, Inc. apply at a later date for a supplemental type
certificate to modify any other model included on Type Certificate No.
A22WE to incorporate the same novel or unusual design feature, the
special conditions would apply to that model as well, under the
provisions of Sec. 21.101(a)(1).
Conclusion
This action affects only certain unusual or novel design features
on McDonnell Douglas Corporation Model DC-10-30 and DC-10-40 airplanes,
modified by B&D Instruments & Avionics, Inc. It is not a rule of
general applicability and affects only the applicant who applied to the
FAA for approval of this feature on this airplane.
The substance of these special conditions has been subjected to the
notice and comment procedure in several prior instances and has been
derived without substantive change from those previously issued. It is
unlikely that prior public comment would result in a significant change
from the substance contained herein. For this reason, and because a
delay would significantly affect the certification of the airplane,
which is imminent, the FAA has determined that prior public notice and
comment are unnecessary and impracticable, and good cause exists for
adopting these special conditions immediately. Therefore, these special
conditions are being made effective upon issuance. The FAA is
requesting comments to allow interested persons to submit views that
may not have been submitted in response to the prior opportunities for
comment described above.
List of Subjects in 14 CFR Part 25
Aircraft, Aviation safety, Reporting and recordkeeping
requirements.
The authority citation for these special conditions is as follows:
Authority: 49 U.S.C. app. 1344, 1348(c), 1352, 1354(a), 1355,
1421 through 1431, 1502, 1651(b)(2), 42 U.S.C. 1857f-10, 4321 et
seq.; E.O. 11514; and 49 U.S.C. 106(g).
The Special Conditions
Accordingly, pursuant to the authority delegated to me by the
Administrator, the following special conditions are issued as part of
the supplemental type certification basis for the McDonnell Douglas
Corporation Model DC-10-30 and DC-10-40 airplanes, as modified by B&D
Instruments & Avionics, Inc:
1. Protection From Unwanted Effects of High-Intensity Radiated
Fields (HIRF). Each electrical and electronic system that performs
critical functions must be designed and installed to ensure that the
operation and operational capability of these systems to perform
critical functions are not adversely affected when the airplane is
exposed to high intensity radiated fields external to the airplane.
2. The following definition applies with respect to this special
condition: Critical Function. Functions whose failure would contribute
to or cause a failure condition that would prevent the continued safe
flight and landing of the airplane.
Issued in Renton, Washington, on June 29, 1995.
Darrell M. Pederson,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service, ANM-100.
[FR Doc. 95-17588 Filed 7-18-95; 8:45 am]
BILLING CODE 4910-13-M