[Federal Register Volume 64, Number 155 (Thursday, August 12, 1999)]
[Proposed Rules]
[Pages 43953-43955]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 99-20893]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. 99-NM-117-AD]
RIN 2120-AA64
Airworthiness Directives; Construcciones Aeronauticas, S.A.
(CASA), Model CN-235 Series Airplanes
AGENCY: Federal Aviation Administration, DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: This document proposes the supersedure of an existing
airworthiness directive (AD), applicable to all CASA Model CN-235
series airplanes, that currently requires repetitive eddy current
inspections to detect fatigue cracks in the nose landing gear (NLG)
turning tube, and replacement of cracked tubes. This proposal would add
a requirement for the replacement of the existing NLG turning tube
constructed of aluminum alloy with a new NLG turning tube made of
steel; such replacement would terminate the repetitive inspections.
This proposal is prompted by issuance of mandatory continuing
airworthiness information by a foreign civil airworthiness authority.
The actions specified by the proposed AD are intended to prevent
fatigue cracking and failure of the NLG turning tube, which could
result in reduced structural integrity of the NLG.
DATES: Comments must be received by September 13, 1999.
ADDRESSES: Submit comments in triplicate to the Federal Aviation
Administration (FAA), Transport Airplane Directorate, ANM-114,
Attention: Rules Docket No. 99-NM-117-AD, 1601 Lind Avenue, SW.,
Renton, Washington 98055-4056. Comments may be inspected at this
location between 9:00 a.m. and 3:00 p.m., Monday through Friday, except
Federal holidays.
The service information referenced in the proposed rule may be
obtained from Construcciones Aeronauticas, S.A., Getafe, Madrid, Spain.
This information may be examined at the FAA, Transport Airplane
Directorate, 1601 Lind Avenue, SW., Renton, Washington.
FOR FURTHER INFORMATION CONTACT: Norman B. Martenson, Manager,
International Branch, ANM-116, FAA, Transport Airplane Directorate,
1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425)
227-2110; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Comments Invited
Interested persons are invited to participate in the making of the
proposed rule by submitting such written data, views, or arguments as
they may desire. Communications shall identify the Rules Docket number
and be submitted in triplicate to the address specified above. All
communications received on or before the closing date for comments,
specified above, will be considered before taking action on the
proposed rule. The proposals contained in this notice may be changed in
light of the comments received.
Comments are specifically invited on the overall regulatory,
economic, environmental, and energy aspects of the proposed rule. All
comments submitted will be available, both before and after the closing
date for comments, in the Rules Docket for examination by interested
persons. A report summarizing each FAA-public contact concerned with
the substance of this proposal will be filed in the Rules Docket.
Commenters wishing the FAA to acknowledge receipt of their comments
submitted in response to this notice must submit a self-addressed,
stamped postcard on which the following statement is made: ``Comments
to Docket Number 99-NM-117-AD.'' The postcard will be date stamped and
returned to the commenter.
Availability of NPRMs
Any person may obtain a copy of this NPRM by submitting a request
to the FAA, Transport Airplane Directorate, ANM-114, Attention: Rules
Docket No. 99-NM-117-AD, 1601 Lind Avenue, SW., Renton, Washington
98055-4056.
Discussion
On January 15, 1997, the FAA issued AD 97-02-17, amendment 39-9902
(62 FR 3994, January 28, 1997), applicable to all CASA Model CN-235
series airplanes, to require repetitive eddy
[[Page 43954]]
current inspections to detect fatigue cracks in the nose landing gear
(NLG) turning tube, and replacement of cracked tubes. That action was
prompted by a report of the failure of a NLG turning tube during
landing roll; the failure was attributed to fatigue cracking in the
turning tube. The requirements of that AD are intended to ensure that
fatigue cracking in the NLG turning tube is detected and corrected
before it could cause the failure of the tube and, consequently,
degrade the structural integrity of the NLG.
Action Since Issuance of Previous Rule
In the preamble to AD 97-02-17, the FAA indicated that the actions
required by that AD were considered ``interim action'' until final
action is identified, at which time the FAA may consider further
rulemaking. The FAA now has determined that further rulemaking action
is indeed necessary, and this proposed AD follows that determination.
Explanation of Relevant Service Information
CASA has issued Service Bulletin 35-CSB-32-001, dated February 16,
1999, which describes procedures for replacement of the existing NLG
turning tube constructed of aluminum alloy with a new NLG turning tube
made of steel. The Direccion General de Aviacion Civil (DGAC), which is
the airworthiness authority for Spain, classified this service bulletin
as mandatory and issued Spanish airworthiness directive 01/95, Rev. 2,
dated February 15, 1999, in order to assure the continued airworthiness
of these airplanes in Spain.
FAA's Conclusions
This airplane model is manufactured in Spain and is type
certificated for operation in the United States under the provisions of
section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and
the applicable bilateral airworthiness agreement. Pursuant to this
bilateral airworthiness agreement, the DGAC has kept the FAA informed
of the situation described above. The FAA has examined the findings of
the DGAC, reviewed all available information, and determined that AD
action is necessary for products of this type design that are
certificated for operation in the United States.
Explanation of Requirements of Proposed Rule
Since an unsafe condition has been identified that is likely to
exist or develop on other airplanes of the same type design registered
in the United States, the proposed AD would supersede AD 97-02-17,
amendment 39-9902, to continue to require repetitive eddy current
inspections to detect fatigue cracks in the nose landing gear (NLG)
turning tube, and replacement of cracked tubes. The proposed AD would
add a requirement to replace the existing NLG turning tube constructed
of aluminum alloy with a new NLG turning tube made of steel, which
would terminate the repetitive inspections.
Differences Between Proposed Rule and Related Service Information
Operators should note that, although the parallel Spanish
airworthiness directive does not mandate the accomplishment of required
actions for CASA Model CN-235 series airplane, serial number C-011, the
applicability of this proposed AD would include that airplane. Although
that airplane was not certificated for civilian operation by the DGAC,
the FAA has certificated it as such. The FAA has determined that the
unsafe condition addressed in this AD may also exist or develop on that
airplane.
Cost Impact
The FAA estimates that 2 airplanes of U.S. registry would be
affected by this proposed AD.
The actions that are currently required by AD 97-02-17, and
retained in this AD, take approximately 8 work hours per airplane to
accomplish, at an average labor rate of $60 per work hour. Based on
these figures, the cost impact of the currently required actions on
U.S. operators is estimated to be $480 per airplane.
The new actions that are proposed in this AD action would take
approximately 16 work hours per airplane to accomplish, at an average
labor rate of $60 per work hour. Required parts would cost
approximately $20,722 per airplane. Based on these figures, the cost
impact of the proposed AD on U.S. operators is estimated to be $43,364,
or $21,682 per airplane.
The cost impact figures discussed above are based on assumptions
that no operator has yet accomplished any of the proposed requirements
of this AD action, and that no operator would accomplish those actions
in the future if this AD were not adopted.
Regulatory Impact
The regulations proposed herein would not have substantial direct
effects on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, in
accordance with Executive Order 12612, it is determined that this
proposal would not have sufficient federalism implications to warrant
the preparation of a Federalism Assessment.
For the reasons discussed above, I certify that this proposed
regulation (1) is not a ``significant regulatory action'' under
Executive Order 12866; (2) is not a ``significant rule'' under the DOT
Regulatory Policies and Procedures (44 FR 11034, February 26, 1979);
and (3) if promulgated, will not have a significant economic impact,
positive or negative, on a substantial number of small entities under
the criteria of the Regulatory Flexibility Act. A copy of the draft
regulatory evaluation prepared for this action is contained in the
Rules Docket. A copy of it may be obtained by contacting the Rules
Docket at the location provided under the caption ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration proposes to amend
part 39 of the Federal Aviation Regulations (14 CFR part 39) as
follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. Section 39.13 is amended by removing amendment 39-9902 (62 FR
3994, January 28, 1997), and by adding a new airworthiness directive to
read as follows:
Construcciones Aeronauticas, S.A. (CASA): Docket 99-NM-117-AD.
Supersedes AD 97-02-17, amendment 39-9902.
Applicability: All Model CN-235 series airplanes; including
Model CN-235 series airplane, serial number C-011; certificated in
any category.
Note 1: This AD applies to each airplane identified in the
preceding applicability provision, regardless of whether it has been
modified, altered, or repaired in the area subject to the
requirements of this AD. For airplanes that have been modified,
altered, or repaired so that the performance of the requirements of
this AD is affected, the owner/operator must request approval for an
alternative method of compliance in accordance with paragraph (f) of
this AD. The request should include an assessment of the
[[Page 43955]]
effect of the modification, alteration, or repair on the unsafe
condition addressed by this AD; and, if the unsafe condition has not
been eliminated, the request should include specific proposed
actions to address it.
Compliance: Required as indicated, unless accomplished
previously.
To prevent fatigue cracking and failure of the nose landing gear
(NLG) turning tube, which could result in reduced structural
integrity of the NLG, accomplish the following:
Restatement of Requirements of AD 97-02-17, Amendment 39-9902
(a) At the applicable time specified in either paragraph (a)(1)
or (a)(2) of this AD, conduct a high frequency eddy current (HFEC)
inspection to detect fatigue cracking in the NLG turning tube, in
accordance with the procedures specified in Annex 1 and Annex 2 of
CASA Maintenance Instructions COM 235-092, Revision 02, dated May 5,
1995.
(1) For Model CN-235 airplanes [Basic model; Maximum Takeoff
Weight (MTOW) = 31,746 lbs. (14,400 kgs.)]: Conduct the inspection
prior to or upon the accumulation of 6,000 landings on the NLG
turning tube, or within 50 landings after March 4, 1997 (the
effective date of AD 97-02-17, amendment 39-9902), whichever occurs
later.
(2) For Model CN-235-100 series airplanes [MTOW = 33,290 lbs.
(15,100 kgs.)] and Model CN-235-200 series airplanes [MTOW = 34,833
lbs. (15,800 kgs)]: Conduct the inspection prior to or upon the
accumulation of 4,800 landings on the NLG turning tube, or within 50
landings after March 4, 1997, whichever occurs later.
(b) If no cracking is detected during the inspection required by
paragraph (a) of this AD, repeat the inspection thereafter at
intervals not to exceed 200 landings until the requirements of
paragraph (d) are accomplished.
(c) If any cracking is detected during any inspection required
by paragraph (a) or (b) of this AD, prior to further flight,
accomplish the actions required by paragraph (c)(1) or (c)(2) of
this AD. After the effective date of this AD, only the actions
specified by paragraph (c)(2) of this AD shall be accomplished.
(1) Replace the NLG turning tube with a new unit in accordance
with CASA Maintenance Instructions COM 235-092, Revision 02, dated
May 5, 1995. After replacement, repeat the HFEC inspection prior to
or upon the accumulation of 6,000 landings on the new NLG turning
tube installed on Model CN-325 airplanes (basic model); or prior to
or upon the accumulation of 4,800 landings on the new NLG turning
tube installed on Model CN-325-100 and -200 series airplanes.
Thereafter, repeat the inspection at intervals not to exceed 200
landings.
(2) Remove the NLG turning tube, P/N GA 63433, from the NLG yoke
assembly and install a new turning tube, P/N GA 65924, and identify
the modified NLG with a P/N SB-A0002-0101 data plate with the
service bulletin number inscribed, in accordance with CASA Service
Bulletin 35-CSB-32-001, dated February 16, 1999.
New Requirements of This AD
(d) Remove the NLG turning tube, P/N GA 63433, from the NLG yoke
assembly and install a new turning tube, P/N GA 65924, and identify
the modified NLG with a P/N SB-A0002-0101 data plate with the
service bulletin number inscribed, in accordance with CASA Service
Bulletin 35-CSB-32-001, dated February 16, 1999. Except as provided
by paragraph (c)(2) of this AD, accomplish the actions at the later
of the times specified in paragraphs (d)(1) and (d)(2) of this AD.
Accomplishment of these actions constitutes terminating action for
the requirements of this AD.
(1) Prior to the accumulation of 4,800 total flight cycles; or
(2) Within 1 year or 200 landings after the effective date of
this AD, whichever occurs first.
(e) As of the effective date of this AD, no person shall install
a NLG turning tube, P/N GA 63433, on any airplane.
Alternative Methods of Compliance
(f) An alternative method of compliance or adjustment of the
compliance time that provides an acceptable level of safety may be
used if approved by the Manager, International Branch, ANM-116, FAA,
Transport Airplane Directorate. Operators shall submit their
requests through an appropriate FAA Principal Maintenance Inspector,
who may add comments and then send it to the Manager, International
Branch, ANM-116.
Note 2: Information concerning the existence of approved
alternative methods of compliance with this AD, if any, may be
obtained from the International Branch, ANM-116.
Special Flight Permits
(g) Special flight permits may be issued in accordance with
sections 21.197 and 21.199 of the Federal Aviation Regulations (14
CFR 21.197 and 21.199) to operate the airplane to a location where
the requirements of this AD can be accomplished.
Note 3: The subject of this AD is addressed in Spanish
airworthiness directive 01/95, Rev. 2, dated February 15, 1999.
Issued in Renton, Washington, on August 6, 1999.
D. L. Riggin,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 99-20893 Filed 8-11-99; 8:45 am]
BILLING CODE 4910-13-U
