2019-16808. Airworthiness Directives; Bombardier, Inc., Airplanes  

  • Start Preamble

    AGENCY:

    Federal Aviation Administration (FAA), DOT.

    ACTION:

    Notice of proposed rulemaking (NPRM).

    SUMMARY:

    The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier, Inc., Model CL-600-1A11 (600), CL-600-2A12 (601), and CL-600-2B16 (601-3A and 601-3R Variants) airplanes. This proposed AD was prompted by reports of the loss of all air data system information provided to the flightcrew, which was caused by icing at high altitudes. This proposed AD would require revising the exisitng airplane flight manual (AFM) to provide the flightcrew with procedures for “Unreliable Airspeed” that stabilize the airplane's airspeed and attitude. The FAA is proposing this AD to address the unsafe condition on these products.

    DATES:

    The FAA must receive comments on this proposed AD by September 26, 2019.

    ADDRESSES:

    You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods:

    • Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
    • Fax: 202-493-2251.
    • Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.
    • Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

    For service information identified in this NPRM, contact Bombardier, Inc., 200 Côte-Vertu Road West, Dorval, Québec H4S 2A3, Canada; North America toll-free telephone 1-866-538-1247 or direct-dial telephone 1-514-855-2999; email ac.yul@aero.bombardier.com; internet http://www.bombardier.com. You may view this service information at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195.

    Examining the AD Docket

    You may examine the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-0582; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, the regulatory evaluation, any comments received, and other information. The street address for Docket Operations is listed above. Comments will be available in the AD docket shortly after receipt.

    Start Further Info

    FOR FURTHER INFORMATION CONTACT:

    John DeLuca, Aerospace Engineer, Avionics and Electrical Systems Services Section, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7369; fax 516-794-5531; email 9-avs-nyaco-cos@faa.gov.

    End Further Info End Preamble Start Supplemental Information

    SUPPLEMENTARY INFORMATION:

    Comments Invited

    The FAA invites you to send any written relevant data, views, or arguments about this proposal. Send your comments to an address listed under the ADDRESSES section. Include “Docket No. FAA-2019-0582; Product Identifier 2019-NM-034-AD” at the beginning of your comments. The FAA specifically invites comments on the overall regulatory, economic, environmental, and energy aspects of this NPRM. The FAA will consider all Start Printed Page 39779comments received by the closing date and may amend this NPRM because of those comments.

    The FAA will post all comments received, without change, to http://www.regulations.gov,, including any personal information you provide. The FAA will also post a report summarizing each substantive verbal contact received about this NPRM.

    Discussion

    Transport Canada Civil Aviation (TCCA), which is the aviation authority for Canada, has issued Canadian AD CF-2018-36, dated December 27, 2018 (referred to after this as the Mandatory Continuing Airworthiness Information, or “the MCAI”), to correct an unsafe condition for certain Bombardier, Inc., Model CL-600-1A11 (600), CL-600-2A12 (601), and CL-600-2B16 (601-3A and 601-3R Variants) airplanes. The MCAI states:

    A number of in-service incidents have been reported on CL-600-2C10 aeroplanes regarding the loss of all air data system information provided to the crew. The air data system information was recovered as the aeroplanes descended to lower altitudes. An investigation determined that the root cause in both events was high altitude icing (ice crystal contamination). If not recognized and addressed, this condition may affect continued safe flight and landing.

    Due to similarities in the air data systems, similar events could also occur on Bombardier Inc. CL-600-1A11, CL-600-2A12 and CL-600-2B16 aeroplanes.

    This [Canadian] AD mandates the incorporation of Airplane Flight Manual (AFM) procedures that will allow the crew to stabilize the aeroplane's airspeed and attitude for continued safe flight and landing.

    You may examine the MCAI in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-0582.

    Related Service Information Under 1 CFR Part 51

    Bombardier has issued the following service information, which provides a procedure for “Unreliable Airspeed” in the Emergency Procedures section of the applicable AFM.

    • Canadair Challenger CL-600-1A11 AFM, Product Publication (PP) 600, Revision A111, dated August 31, 2018.
    • Canadair Challenger CL-600-1A11 (Winglets) AFM, Product Support Publication (PSP) 600-1, Revision 103, dated August 31, 2018.
    • Canadair Challenger CL-600-2A12 AFM, PSP 601-1A, Revision 120, dated August 31, 2018.
    • Canadair Challenger CL-600-2A12 AFM, PSP 601-1A-1, Revision 79, dated August 31, 2018.
    • Canadair Challenger CL-600-2A12 AFM, PSP 601-1B, Revision 83, dated August 31, 2018.
    • Canadair Challenger CL-600-2A12 AFM, PSP 601-1B-1, Revision 81, dated August 31, 2018.
    • Canadair Challenger CL-600-2B16 AFM, PSP 601A-1, Revision 103, dated August 31, 2018.
    • Canadair Challenger CL-600-2B16 AFM, PSP 601A-1-1, Revision 92, dated August 31, 2018.

    These documents are distinct since they apply to different airplane models in different configurations. This service information is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section.

    FAA's Determination

    This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to a bilateral agreement with the State of Design Authority, the FAA has been notified of the unsafe condition described in the MCAI and service information referenced above. The FAA is proposing this AD because the agency evaluated all the relevant information and determined the unsafe condition described previously is likely to exist or develop on other products of the same type design.

    Proposed Requirements of This NPRM

    This proposed AD would require revising the existing AFM with procedures for “Unreliable Airspeed” in the Emergency Procedures section of the applicable AFM as described previously.

    Costs of Compliance

    The FAA estimates that this proposed AD affects 206 airplanes of U.S. registry. The FAA estimates the following costs to comply with this proposed AD:

    Estimated Costs for Required Actions

    Labor costParts costCost per productCost on U.S. operators
    1 work-hour × $85 per hour = $85$0$85$17,510

    Authority for This Rulemaking

    Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority.

    The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: “General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

    This proposed AD is issued in accordance with authority delegated by the Executive Director, Aircraft Certification Service, as authorized by FAA Order 8000.51C. In accordance with that order, issuance of ADs is normally a function of the Compliance and Airworthiness Division, but during this transition period, the Executive Director has delegated the authority to issue ADs applicable to transport category airplanes and associated appliances to the Director of the System Oversight Division.

    Regulatory Findings

    The FAA determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

    For the reasons discussed above, I certify this proposed regulation:

    (1) Is not a “significant regulatory action” under Executive Order 12866,

    (2) Will not affect intrastate aviation in Alaska, and

    (3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities Start Printed Page 39780under the criteria of the Regulatory Flexibility Act.

    Start List of Subjects

    List of Subjects in 14 CFR Part 39

    • Air transportation
    • Aircraft
    • Aviation safety
    • Incorporation by reference
    • Safety
    End List of Subjects

    The Proposed Amendment

    Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

    Start Part

    PART 39—AIRWORTHINESS DIRECTIVES

    End Part Start Amendment Part

    1. The authority citation for part 39 continues to read as follows:

    End Amendment Part Start Authority

    Authority: 49 U.S.C. 106(g), 40113, 44701.

    End Authority
    [Amended]
    Start Amendment Part

    2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD):

    End Amendment Part

    Bombardier, Inc.: Docket No. FAA-2019-0582; Product Identifier 2019-NM-034-AD.

    (a) Comments Due Date

    The FAA must receive comments by September 26, 2019.

    (b) Affected ADs

    None.

    (c) Applicability

    This AD applies to Bombardier, Inc., airplanes, certificated in any category, identified in paragraphs (c)(1) through (c)(3) of this AD.

    (1) Model CL-600-1A11 (600), serial numbers 1001 through 1085 inclusive.

    (2) Model CL-600-2A12 (601), serial numbers 3001 through 3066 inclusive.

    (3) Model CL-600-2B16 (601-3A and 601-3R Variants), serial numbers 5001 through 5194 inclusive.

    (d) Subject

    Air Transport Association (ATA) of America Code 34, Navigation.

    (e) Reason

    This AD was prompted by reports of the loss of all air data system information provided to the flightcrew, which was caused by icing at high altitudes. The FAA is issuing this AD to address the loss of all air data system information provided to the flightcrew. If not addressed, this condition may adversely affect continued safe flight and landing.

    (f) Compliance

    Comply with this AD within the compliance times specified, unless already done.

    (g) Revision of the Airplane Flight Manual (AFM)

    Within 30 days after the effective date of this AD: Revise the Emergency Procedures section of the existing AFM to include the information in the “Unreliable Airspeed” procedure of the applicable AFM specified in figure 1 to paragraph (g) of this AD.

    Start Printed Page 39781

    Start Printed Page 39782

    (h) Other FAA AD Provisions

    The following provisions also apply to this AD:

    (1) Alternative Methods of Compliance (AMOCs): The Manager, New York ACO Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the certification office, send it to ATTN: Program Manager, Continuing Operational Safety, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office.

    (2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, New York ACO Branch, FAA; or Transport Canada Civil Aviation (TCCA); or Bombardier, Inc.'s TCCA Design Approval Organization (DAO). If approved by the DAO, the approval must include the DAO-authorized signature.

    (i) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) Canadian AD CF-2018-36, dated December 27, 2018, for related information. This MCAI may be found in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2019-0582.

    (2) For more information about this AD, contact John DeLuca, Aerospace Engineer, Avionics and Electrical Systems Services Section, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 516-228-7369; fax 516-794-5531; email 9-avs-nyaco-cos@faa.gov.

    (3) For service information identified in this AD, contact Bombardier, Inc., 200 Côte-Vertu Road West, Dorval, Québec H4S 2A3, Canada; North America toll-free telephone 1-866-538-1247 or direct-dial telephone 1-514-855-2999; email ac.yul@aero.bombardier.com; internet http://www.bombardier.com. You may view this service information at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195.

    Start Signature

    Issued in Des Moines, Washington, on July 26, 2019.

    Dionne Palermo,

    Acting Director, System Oversight Division, Aircraft Certification Service.

    End Signature End Supplemental Information

    BILLING CODE 4910-13-P

    BILLING CODE 4910-13-C

    [FR Doc. 2019-16808 Filed 8-9-19; 8:45 am]

    BILLING CODE 4910-13-P

Document Information

Published:
08/12/2019
Department:
Federal Aviation Administration
Entry Type:
Proposed Rule
Action:
Notice of proposed rulemaking (NPRM).
Document Number:
2019-16808
Dates:
The FAA must receive comments on this proposed AD by September 26, 2019.
Pages:
39778-39782 (5 pages)
Docket Numbers:
Docket No. FAA-2019-0582, Product Identifier 2019-NM-034-AD
RINs:
2120-AA64: Airworthiness Directives
RIN Links:
https://www.federalregister.gov/regulations/2120-AA64/airworthiness-directives
Topics:
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety
PDF File:
2019-16808.Pdf
CFR: (1)
14 CFR 39.13