[Federal Register Volume 64, Number 147 (Monday, August 2, 1999)]
[Proposed Rules]
[Pages 41841-41842]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 99-19744]
========================================================================
Proposed Rules
Federal Register
________________________________________________________________________
This section of the FEDERAL REGISTER contains notices to the public of
the proposed issuance of rules and regulations. The purpose of these
notices is to give interested persons an opportunity to participate in
the rule making prior to the adoption of the final rules.
========================================================================
Federal Register / Vol. 64, No. 147 / Monday, August 2, 1999 /
Proposed Rules
[[Page 41841]]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. 99-SW-07-AD]
Airworthiness Directives; Bell Helicopter Textron Canada (BHTC)
Model 407 Helicopters
AGENCY: Federal Aviation Administration, DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: This document proposes the adoption of a new airworthiness
directive (AD) that is applicable to BHTC Model 407 helicopters. This
proposal would require visually inspecting the vertical fin (fin) for
reduced skin thickness; repairing or replacing the fin, if necessary;
and identifying fins that have been inspected or repaired. This
proposal is prompted by a report of an inboard skin damaged during
production. The actions specified by the proposed AD are intended to
detect fin assemblies with reduced skin thickness which, if not
corrected, reduce the strength of the skin, and could lead to failure
of the fin and loss of control of the helicopter.
DATES: Comments must be received on or before October 1, 1999.
ADDRESSES: Submit comments in triplicate to the Federal Aviation
Administration (FAA), Office of the Regional Counsel, Southwest Region,
Attention: Rules Docket No. 99-SW-07-AD, 2601 Meacham Blvd., Room 663,
Fort Worth, Texas 76137. Comments may be inspected at this location
between 9:00 a.m. and 3:00 p.m., Monday through Friday, except Federal
holidays.
The service information referenced in the proposed rule may be
obtained from Bell Helicopter Textron Canada, 12,800 Rue de l'Avenir,
Mirabel, Quebec JON1LO, telephone (800) 463-3036, fax (514) 433-0272.
This information may be examined at the FAA, Office of the Regional
Counsel, Southwest Region, Room 663, Fort Worth, Texas.
FOR FURTHER INFORMATION CONTACT: Mike Kohner, Aerospace Engineer, FAA,
Rotorcraft Directorate, Rotorcraft Certification Office, Fort Worth,
Texas 76193-0170, telephone (817) 222-5447, fax (817) 222-5783.
SUPPLEMENTARY INFORMATION:
Comments Invited
Interested persons are invited to participate in the making of the
proposed rule by submitting such written data, views, or arguments as
they may desire. Communications should identify the Rules Docket number
and be submitted in triplicate to the address specified above. All
communications received on or before the closing date for comments,
specified above, will be considered before taking action on the
proposed rule. The proposals contained in this notice may be changed in
light of the comments received.
Comments are specifically invited on the overall regulatory,
economic, environmental, and energy aspects of the proposed rule. All
comments submitted will be available, both before and after the closing
date for comments, in the Rules Docket for examination by interested
persons. A report summarizing each FAA-public contact concerned with
the substance of this proposal will be filed in the Rules Docket.
Commenters wishing the FAA to acknowledge receipt of their comments
submitted in response to this notice must submit a self-addressed,
stamped postcard on which the following statement is made: ``Comments
to Docket No. 99-SW-07-AD.'' The postcard will be date stamped and
returned to the commenter.
Availability of NPRMs
Any person may obtain a copy of this NPRM by submitting a request
to the FAA, Office of the Regional Counsel, Southwest Region,
Attention: Rules Docket No. 99-SW-07-AD, 2601 Meacham Blvd., Room 663,
Fort Worth, Texas 76137.
Discussion
Transport Canada, which is the airworthiness authority for Canada,
has notified the FAA that an unsafe condition may exist on BHTC Model
407 helicopters. Transport Canada advises some fin assemblies may have
a reduced skin thickness which decreases the strength of the fin. If
not corrected, this situation can lead to cracking of the vertical fin
assembly.
BHTC has issued Bell Helicopter Textron Alert Service Bulletin No.
407-98-17, Revision A, dated June 26, 1998, which specifies a visual
inspection for certain fin assemblies. It also provides for the repair
and fluorescent penetrant inspection of repaired fin assemblies. It
further provides for marking the vertical fin to show it is in
compliance with the service bulletin. Transport Canada classified this
service bulletin as mandatory and issued AD No. CF-98-10R1, dated
August 20, 1998, in order to assure the continued airworthiness of
these helicopters in Canada.
This helicopter model is manufactured in Canada and is type
certificated for operation in the United States under the provisions of
Sec. 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the
applicable bilateral airworthiness agreement. Pursuant to this
bilateral airworthiness agreement, Transport Canada has kept the FAA
informed of the situation described above. The FAA has examined the
findings of Transport Canada, reviewed all available information, and
determined that AD action is necessary for products of this type design
that are certificated for operation in the United States.
Since an unsafe condition has been identified that is likely to
exist or develop on other BHTC Model 407 helicopters of the same type
design registered in the United States, the proposed AD would require
visually inspecting certain serial-numbered fins, part number 206-020-
113-223A, -223B, or -223S, for reduced skin thickness; repairing or
replacing the vertical fin, if necessary; and marking fins that have
been inspected or repaired. This proposal is prompted by a report of an
inboard skin damaged during production. The actions would be required
to be accomplished in accordance with the service bulletin described
previously.
Cost Impact
The FAA estimates that 124 helicopters of U.S. registry would be
affected by this proposed AD, that it would take approximately 3.0 work
hours to accomplish the visual
[[Page 41842]]
inspection; 4.0 work hours to accomplish the vertical fin replacement,
and 0.5 work hour to mark the fin, and that the average labor rate is
$60 per work hour. Required parts would cost approximately $18,770.
Based on these figures, the total cost impact of the proposed AD on
U.S. operators is estimated to be $19,220 per helicopter, or a total of
$2,383,280 for the entire fleet, to accomplish all the actions
including replacing the fin.
Regulatory Impact
The regulations proposed herein would not have substantial direct
effects on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, in
accordance with Executive Order 12612, it is determined that this
proposal would not have sufficient federalism implications to warrant
the preparation of a Federalism Assessment.
For the reasons discussed above, I certify that this proposed
regulation (1) is not a ``significant regulatory action'' under
Executive Order 12866; (2) is not a ``significant rule'' under the DOT
Regulatory Policies and Procedures (44 FR 11034, February 26, 1979);
and (3) if promulgated, will not have a significant economic impact,
positive or negative, on a substantial number of small entities under
the criteria of the Regulatory Flexibility Act. A copy of the draft
regulatory evaluation prepared for this action is contained in the
Rules Docket. A copy of it may be obtained by contacting the Rules
Docket at the location provided under the caption ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration proposes to amend
part 39 of the Federal Aviation Regulations (14 CFR part 39) as
follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. Section 39.13 is amended by adding a new airworthiness directive
to read as follows:
Bell Helicopter Textron Canada: Docket No. 99-SW-07-AD.
Applicability: Model 407 helicopters, with vertical fin (fin)
assembly, part number (P/N) 206-020-113-223A, -223B, or -223S, with
a serial number with a prefix of ``BP'', up to and including 2266
(except BP2260, BP2262, and BP2265), installed, certificated in any
category.
Note 1: This AD applies to each helicopter identified in the
preceding applicability provision, regardless of whether it has been
otherwise modified, altered, or repaired in the area subject to the
requirements of this AD. For helicopters that have been modified,
altered, or repaired so that the performance of the requirements of
this AD is affected, the owner/operator must request approval for an
alternative method of compliance in accordance with paragraph (c) of
this AD. The request should include an assessment of the effect of
the modification, alteration, or repair on the unsafe condition
addressed by this AD; and, if the unsafe condition has not been
eliminated, the request should include specific proposed actions to
address it.
Compliance: Required within 100 hours time-in-service, unless
accomplished previously.
To detect fin assemblies with reduced skin thickness which, if
not corrected, reduce the strength of the skin, and could lead to
failure of the vertical fin (fin) and subsequent loss of control of
the helicopter, accomplish the following:
(a) Visually inspect the fin assembly for reduced skin
thickness, indicated by notches, scratches, or grooves on the skin,
in accordance with Part I of the Accomplishment Instructions
contained in Bell Helicopter Textron Alert Service Bulletin No. 407-
98-17, Revision A, dated June 26, 1998 (ASB). If notches, scratches,
or grooves are found, repair or replace the fin assembly in
accordance with Part II of the Accomplishment Instructions contained
in the ASB .
(b) Identify any fin that has been inspected or repaired in
accordance with Part III of the Accomplishment Instructions in the
ASB.
(c) An alternative method of compliance or adjustment of the
compliance time that provides an acceptable level of safety may be
used if approved by the Manager, Rotorcraft Certification Office,
Rotorcraft Directorate, FAA. Operators shall submit their requests
through a FAA Principal Maintenance Inspector, who may concur or
comment and then send it to the Manager, Rotorcraft Certification
Office.
Note 2: Information concerning the existence of approved
alternative methods of compliance with this AD, if any, may be
obtained from the Rotorcraft Certification Office.
(d) Special flight permits may be issued in accordance with
sections 21.197 and 21.199 of the Federal Aviation Regulations (14
CFR 21.197 and 21.199) to operate the helicopter to a location where
the requirements of this AD can be accomplished.
Note 3: The subject of this AD is addressed in Transport Canada
(Canada) AD No. CF-98-10R1, dated August 20, 1998.
Issued in Fort Worth, Texas, on July 26, 1999.
Henry A. Armstrong,
Manager, Rotorcraft Directorate, Aircraft Certification Service.
[FR Doc. 99-19744 Filed 7-30-99; 8:45 am]
BILLING CODE 4910-13-U
