2023-18036. Tin Mill Products From the People's Republic of China: Preliminary Affirmative Determination of Sales at Less Than Fair Value and Preliminary Affirmative Determination of Critical Circumstances

AGENCY:

Enforcement and Compliance, International Trade Administration, Department of Commerce.

SUMMARY:

The U.S. Department of Commerce (Commerce) preliminarily determines that tin mill products from the People's Republic of China (China) are being, or are likely to be, sold in the United States at less than fair value (LTFV). The period of investigation (POI) is July 1, 2022, through December 31, 2022. Interested parties are invited to comment on this preliminary determination.

DATES:

Applicable August 22, 2023.

FOR FURTHER INFORMATION CONTACT:

Samuel Frost, AD/CVD Operations, Office V, Enforcement and Compliance, International Trade Administration, U.S. Department of Commerce, 1401 Constitution Avenue NW, Washington, DC 20230; telephone: [phone].

SUPPLEMENTARY INFORMATION:

Background

This preliminary determination is made in accordance with section 733(b) of the Tariff Act of 1930, as amended (the Act). Commerce published the notice of initiation of this LTFV investigation on February 14, 2023.^[1] On May 31, 2023, Commerce postponed the preliminary determination of this investigation and the revised deadline is now August 16, 2023.^[2] For a complete description of the events that followed the initiation of this investigation, see the Preliminary Decision Memorandum.^[3] A list of topics included in the Preliminary Decision Memorandum is included as Appendix II to this notice. The Preliminary Decision Memorandum is a public document and is on file electronically via Enforcement and Compliance's Antidumping and Countervailing Duty Centralized Electronic Service System (ACCESS). ACCESS is available to registered users at https://access.trade.gov. In addition, a complete version of the Preliminary Decision Memorandum can be accessed directly at https://access.trade.gov/​public/​FRNoticesListLayout.aspx.

Scope of the Investigation

The products covered by this investigation are tin mill products from China. For a complete description of the scope of this investigation, see Appendix I.

Scope Comments

In accordance with the preamble to Commerce's regulations,^[4] the Initiation Notice set aside a period of time for parties to raise issues regarding product coverage (scope).^[5] Certain interested parties commented on the scope of the investigation as it appeared in the Initiation Notice. For a summary of product coverage comments and rebuttal responses submitted to the record for this investigation, and accompanying discussion and analysis of all comments timely received, see the Preliminary Scope Decision Memorandum.^[6] Commerce preliminarily did not modify the scope language as it appeared in the Initiation Notice. In the Preliminary Scope Decision Memorandum, Commerce established a deadline for parties to submit scope and rebuttal briefs.

Methodology

Commerce is conducting this investigation in accordance with section 731 of the Act. Furthermore, pursuant to sections 776(a) and (b) of the Act, Commerce preliminarily has relied upon facts otherwise available, with adverse inferences, for the China-wide entity. For a full description of the methodology underlying Commerce's preliminary determination, see the Preliminary Decision Memorandum.

Preliminary Affirmative Determination of Critical Circumstances

In accordance with section 733(e) of the Act and 19 CFR 351.206(c), Commerce preliminarily determines that critical circumstances exist with respect to imports of tin mill products from China for the China-wide entity. For a full description of the methodology and results of Commerce's critical circumstances analysis, see the Preliminary Decision Memorandum.

Combination Rates

In the Initiation Notice,^[7] Commerce stated that it would calculate producer/exporter combination rates for the respondents that are eligible for a separate rate in this investigation. Policy Bulletin 05.1 describes this practice.^[8] In this case, because no respondent qualified for a separate rate, we did not calculate any producer/exporter combination rates. For a full description of the separate rate status of interested parties in this investigation, see the Preliminary Decision Memorandum.

Preliminary Determination

Commerce preliminarily determines that the following estimated weighted-average dumping margin exists:

Producer/exporter	Estimated weighted- average dumping margin (percent)	Cash deposit rate (adjusted for subsidy offset (percent))
China-wide Entity	122.52	111.98

Suspension of Liquidation

In accordance with section 733(d)(2) of the Act, Commerce will direct U.S. Customs and Border Protection (CBP) to suspend liquidation of subject merchandise as described in the scope of the investigation entered, or withdrawn from warehouse, for consumption on or after the date of publication of this notice in the Federal Register , as discussed below. Further, pursuant to section 733(d)(1)(B) of the Act and 19 CFR 351.205(d), Commerce will instruct CBP to require a cash deposit equal to the weighted-average amount by which normal value exceeds U.S. price, as indicated in the chart above.

Section 733(e)(2) of the Act provides that, given an affirmative determination of critical circumstances, any suspension of liquidation shall apply to unliquidated entries of merchandise entered, or withdrawn from warehouse, for consumption on or after the later of (a) the date which is 90 days before the date on which the suspension of liquidation was first ordered, or (b) the date on which notice of initiation of the investigation was published. Commerce preliminarily finds that critical circumstances exist for imports of subject merchandise from the China-wide entity. In accordance with section 733(e)(2)(A) of the Act, the suspension of liquidation shall apply to all unliquidated entries of merchandise from all producers and/or exporters of tin mill products from China that were entered, or withdrawn from warehouse, for consumption on or after the date which is 90 days before the publication of this notice in the Federal Register .

To determine the cash deposit rate, Commerce normally adjusts the estimated weighted-average dumping margin by the amount of domestic subsidy pass-through and export subsidies determined in a companion countervailing duty (CVD) proceeding when CVD provisional measures are in effect. Accordingly, where Commerce has made a preliminary affirmative determination for domestic subsidy pass-through or export subsidies, Commerce has offset the calculated estimated weighted-average dumping margin by the appropriate rate(s). As discussed in the Preliminary Decision Memorandum, we made no adjustment for domestic subsidy pass-through. Any such adjusted rates may be found in the Preliminary Determination Section's chart of estimated weighted-average dumping margins above.

Should provisional measures in the companion CVD investigation expire prior to the expiration of provisional measures in this LTFV investigation, Commerce will direct CBP to begin collecting cash deposits at a rate equal to the estimated weighted-average dumping margin calculated in this preliminary determination unadjusted for export subsidies at the time the CVD provisional measures expire. These suspension of liquidation instructions will remain in effect until further notice.

Disclosure

Normally, Commerce discloses to interested parties the calculations performed in connection with a preliminary determination within five days of its public announcement or, if there is no public announcement, within five days of the date of publication of this notice in accordance with 19 CFR 351.224(b). However, because Commerce preliminarily applied total adverse facts available (AFA) to the China-wide entity in this investigation, in accordance with section 776 of the Act, and the applied AFA rate is based solely on the petition, there are no calculations to disclose.

Verification

Because the China-wide entity in this investigation did not provide information requested by Commerce, and Commerce preliminarily determines that the China-wide entity was uncooperative, we will not conduct verification.

Public Comment

Case briefs or other written comments on non-scope issues may be submitted to the Assistant Secretary for Enforcement and Compliance no later than September 8, 2023. Rebuttal briefs, limited to issues raised in case briefs, may be submitted no later than seven days after the deadline date for case briefs.^[9] Note that Commerce has temporarily modified certain of its requirements for serving documents containing business proprietary information, until further notice.^[10] Pursuant to 19 CFR 351.309(c)(2) and (d)(2), parties who submit case or rebuttal briefs in this investigation are encouraged to submit with each argument: (1) a statement of the issue; (2) a brief summary of the argument; and (3) a table of authorities.

Pursuant to 19 CFR 351.310(c), interested parties who wish to request a hearing, limited to issues raised in the case and rebuttal briefs, must submit a written request to the Assistant Secretary for Enforcement and Compliance, U.S. Department of Commerce, within 30 days after the date of publication of this notice. Requests should contain the party's name, address, and telephone number, the number of participants, whether any participant is a foreign national, and a list of the issues to be discussed. If a request for a hearing is made, Commerce intends to hold the hearing at a time and date to be determined. Parties should confirm the date and time of the hearing two days before the scheduled date.

Final Determination

Section 735(a)(1) of the Act and 19 CFR 351.210(b)(1) provide that Commerce will issue the final determination within 75 days after the date of its preliminary determination. Accordingly, Commerce will make its final determination no later than 75 days after the signature date of this preliminary determination.

International Trade Commission Notification

In accordance with section 733(f) of the Act, Commerce will notify the U.S. International Trade Commission (ITC) of its preliminary determination. If the final determination is affirmative, the ITC will determine before the later of 120 days after the date of this preliminary determination or 45 days after the final determination whether these imports are materially injuring, or threaten material injury to, the U.S. industry.

Notification to Interested Parties

This determination is issued and published in accordance with sections 733(f) and 777(i)(1) of the Act, and 19 CFR 351.205(c).

Dated: August 16, 2023.

Lisa W. Wang,

Assistant Secretary for Enforcement and Compliance.

Appendix I

Scope of the Investigation

The products within the scope of the investigation are tin mill flat-rolled products that are coated or plated with tin, chromium, or chromium oxides. Flat-rolled steel products coated with tin are known as tinplate. Flat-rolled steel products coated with chromium or chromium oxides are known as tin-free steel or electrolytic chromium-coated steel. The scope includes all the noted tin mill products regardless of thickness, width, form (in coils or cut sheets), coating type (electrolytic or otherwise), edge (trimmed, untrimmed or further processed, such as scroll cut), coating thickness, surface finish, temper, coating metal (tin, chromium, chromium oxide), reduction (single- or double- reduced), and whether or not coated with a plastic material.

All products that meet the written physical description are within the scope of the investigation unless specifically excluded. The following products are outside and/or specifically excluded from the scope of the investigation:

• Single reduced electrolytically chromium coated steel with a thickness 0.238 mm (85 pound base box) (±10%) or 0.251 mm (90 pound base box) (±10%) or 0.255 mm (±10%) with 770 mm (minimum width) (±1.588 mm) by 900 mm (maximum length if sheared) sheet size or 30.6875 inches (minimum width) (± 1/16 inch) and 35.4 inches (maximum length if sheared) sheet size; with type MR or higher (per ASTM) A623 steel chemistry; batch annealed at T2 1/2 anneal temper, with a yield strength of 31 to 42 kpsi (214 to 290 Mpa); with a tensile strength of 43 to 58 kpsi (296 to 400 Mpa); with a chrome coating restricted to 32 to 150 mg/m² ; with a chrome oxide coating restricted to 6 to 25 mg/m² with a modified 7B ground roll finish or blasted roll finish; with roughness average (Ra) 0.10 to 0.35 micrometers, measured with a stylus instrument with a stylus radius of 2 to 5 microns, a trace length of 5.6 mm, and a cut-off of 0.8 mm, and the measurement traces shall be made perpendicular to the rolling direction; with an oil level of 0.17 to 0.37 grams/base box as type BSO, or 2.5 to 5.5 mg/m² as type DOS, or 3.5 to 6.5 mg/m² as type ATBC; with electrical conductivity of static probe voltage drop of 0.46 volts drop maximum, and with electrical conductivity degradation to 0.70 volts drop maximum after stoving (heating to 400 degrees F for 100 minutes followed by a cool to room temperature).

• Single reduced electrolytically chromium- or tin-coated steel in the gauges of 0.0040 inch nominal, 0.0045 inch nominal, 0.0050 inch nominal, 0.0061 inch nominal (55 pound base box weight), 0.0066 inch nominal (60 pound base box weight), and 0.0072 inch nominal (65 pound base box weight), regardless of width, temper, finish, coating or other properties.
• Single reduced electrolytically chromium coated steel in the gauge of 0.024 inch, with widths of 27.0 inches or 31.5 inches, and with T–1 temper properties.

• Single reduced electrolytically chromium coated steel, with a chemical composition of 0.005% max carbon, 0.030% max silicon, 0.25% max manganese, 0.025% max phosphorous, 0.025% max sulfur 0.070% max aluminum, and the balance iron, with a metallic chromium layer of 70–130 mg/m² , with a chromium oxide layer of 5–30 mg/m² , with a tensile strength of 260–440 N/mm² , with an elongation of 28–48%, with a hardness (HR–30T) of 40–58, with a surface roughness of 0.5–1.5 microns Ra, with magnetic properties of Bm (kg) 10.0 minimum, Br (kg) 8.0 minimum, Hc (Oe) 2.5–3.8, and MU 1400 minimum, as measured with a Riken Denshi DC magnetic characteristic measuring machine, Model BHU–60.

• Bright finish tin-coated sheet with a thickness equal to or exceeding 0.0299 inch, coated to thickness of 3/4 pound (0.000045 inch) and 1 pound (0.00006 inch).

• Electrolytically chromium coated steel having ultra flat shape defined as oil can maximum depth of 5/64 inch (2.0 mm) and edge wave maximum of 5/64 inch (2.0 mm) and no wave to penetrate more than 2.0 inches (51.0 mm) from the strip edge and coilset or curling requirements of average maximum of 5/64 inch (2.0 mm) (based on six readings, three across each cut edge of a 24 inches (61 cm) long sample with no single reading exceeding 4/32 inch (3.2 mm) and no more than two readings at 4/32 inch (3.2 mm)) and (for 85 pound base box item only: crossbuckle maximums of 0.001 inch (0.0025 mm) average having no reading above 0.005 inch (0.127 mm)), with a camber maximum of 1/4 inch (6.3 mm) per 20 feet (6.1 meters), capable of being bent 120 degrees on a 0.002 inch radius without cracking, with a chromium coating weight of metallic chromium at 100 mg/m² and chromium oxide of 10 mg/m² , with a chemistry of 0.13% maximum carbon, 0.60% maximum manganese, 0.15% maximum silicon, 0.20% maximum copper, 0.04% maximum phosphorous, 0.05% maximum sulfur, and 0.20% maximum aluminum, with a surface finish of Stone Finish 7C, with a DOS–A oil at an aim level of 2 mg/square meter, with not more than 15 inclusions/foreign matter in 15 feet (4.6 meters) (with inclusions not to exceed 1/32 inch (0.8 mm) in width and 3/64 inch (1.2 mm) in length), with thickness/temper combinations of either 60 pound base box (0.0066 inch) double reduced CADR8 temper in widths of 25.00 inches, 27.00 inches, 27.50 inches, 28.00 inches, 28.25 inches, 28.50 inches, 29.50 inches, 29.75 inches, 30.25 inches, 31.00 inches, 32.75 inches, 33.75 inches, 35.75 inches, 36.25 inches, 39.00 inches, or 43.00 inches, or 85 pound base box (0.0094 inch) single reduced CAT4 temper in widths of 25.00 inches, 27.00 inches, 28.00 inches, 30.00 inches, 33.00 inches, 33.75 inches, 35.75 inches, 36.25 inches, or 43.00 inches, with width tolerance of 1/8 inch, with a thickness tolerance of 0.0005 inch, with a maximum coil weight of 20,000 pounds (9071.0 kg), with a minimum coil weight of 18,000 pounds (8164.8 kg), with a coil inside diameter of 16 inches (40.64 cm) with a steel core, with a coil maximum outside diameter of 59.5 inches (151.13 cm), with a maximum of one weld (identified with a paper flag) per coil, with a surface free of scratches, holes, and rust.

• Electrolytically tin coated steel having differential coating with 1.00 pound/base box equivalent on the heavy side, with varied coating equivalents in the lighter side (detailed below), with a continuous cast steel chemistry of type MR, with a surface finish of type 7B or 7C, with a surface passivation of 0.7 mg/square foot of chromium applied as a cathodic dichromate treatment, with coil form having restricted oil film weights of 0.3–0.4 grams/base box of type DOS–A oil, coil inside diameter ranging from 15.5 to 17 inches, coil outside diameter of a maximum 64 inches, with a maximum coil weight of 25,000 pounds, and with temper/coating/dimension combinations of: (1) CAT4 temper, 1.00/.050 pound/base box coating, 70 pound/base box (0.0077 inch) thickness, and 33.1875 inch ordered width; or (2) CAT5 temper, 1.00/0.50 pound/base box coating, 75 pound/base box (0.0082 inch) thickness, and 34.9375 inch or 34.1875 inch ordered width; or (3) CAT5 temper, 1.00/0.50 pound/base box coating, 107 pound/base box (0.0118 inch) thickness, and 30.5625 inch or 35.5625 inch ordered width; or (4) CADR8 temper, 1.00/0.50 pound/base box coating, 85 pound/base box (0.0093 inch) thickness, and 35.5625 inch ordered width; or (5) CADR8 temper, 1.00/0.25 pound/base box coating, 60 pound/base box (0.0066 inch) thickness, and 35.9375 inch ordered width; or (6) CADR8 temper, 1.00/0.25 pound/base box coating, 70 pound/base box (0.0077 inch) thickness, and 32.9375 inch, 33.125 inch, or 35.1875 inch ordered width.
• Electrolytically tin coated steel having differential coating with 1.00 pound/base box equivalent on the heavy side, with varied coating equivalents on the lighter side (detailed below), with a continuous cast steel chemistry of type MR, with a surface finish of type 7B or 7C, with a surface passivation of 0.5 mg/square foot of chromium applied as a cathodic dichromate treatment, with ultra flat scroll cut sheet form, with CAT5 temper with 1.00/0.10 pound/base box coating, with a lithograph logo printed in a uniform pattern on the 0.10 pound coating side with a clear protective coat, with both sides waxed to a level of 15–20 mg/216 sq. inch, with ordered dimension combinations of (1) 75 pound/base box (0.0082 inch) thickness and 34.9375 inch x 31.748 inch scroll cut dimensions; or (2) 75 pound/base box (0.0082 inch) thickness and 34.1875 inch x 29.076 inch scroll cut dimensions; or (3) 107 pound/base box (0.0118 inch) thickness and 30.5625 inch x 34.125 inch scroll cut dimension.

• Tin-free steel coated with a metallic chromium layer between 100–200 mg/m² and a chromium oxide layer between 5–30 mg/m² ; chemical composition of 0.05% maximum carbon, 0.03% maximum silicon, 0.60% maximum manganese, 0.02% maximum phosphorous, and 0.02% maximum sulfur; magnetic flux density (Br) of 10 kg minimum and a coercive force (Hc) of 3.8 Oe minimum.

• Tin-free steel laminated on one or both sides of the surface with a polyester film, consisting of two layers (an amorphous layer and an outer crystal layer), that contains no more than the indicated amounts of the following environmental hormones: 1 mg/kg BADGE (BisPhenol—A Di-glycidyl Ether), 1 mg/kg BFDGE (BisPhenol—F Di-glycidyl Ether), and 3 mg/kg BPA (BisPhenol—A).

The merchandise subject to the investigation is currently classified in the Harmonized Tariff Schedule of the United States (HTSUS), under HTSUS subheadings 7210.11.0000, 7210.12.0000, 7210.50.0020, 7210.50.0090, 7212.10.0000, and 7212.50.0000 if of non-alloy steel and under HTSUS subheadings 7225.99.0090, and 7226.99.0180 if of alloy steel. Although the subheadings are provided for convenience and customs purposes, the written description of the scope of the investigation is dispositive.

Appendix II

List of Topics Discussed in the Preliminary Decision Memorandum

I. Summary

II. Background

III. Period of Investigation

IV. Scope of Investigation

V. Selection of Respondents

VI. Discussion of the Methodology

VII. Adjustment Under Section 777A(f) of the Act

VIII. Adjustment to Cash Deposit Rate for Export Subsidies

IX. Preliminary Determination of Critical Circumstances

X. Recommendation

Footnotes

1.   See Tin Mill Products from Canada, the People's Republic of China, Germany, the Netherlands, the Republic of Korea, Taiwan, the Republic of Turkey, and the United Kingdom: Initiation of Less-Than-Fair-Value Investigations,88 FR 9481 (February 14, 2023) ( Initiation Notice).

2.   See Tin Mill Products from Canada, the People's Republic of China, Germany, the Netherlands, the Republic of Korea, Taiwan, the Republic of Turkey, and the United Kingdom: Postponement of Preliminary Determinations in the Less-Than-Fair-Value Investigations,88 FR 34827 (May 31, 2023).

3.   See Memorandum, “Decision Memorandum for Preliminary Affirmative Determination of Sales at Less Than Fair Value and Preliminary Affirmative Determination of Critical Circumstances in the Investigation of Tin Mill Products from the People's Republic of China,” dated concurrently with, and hereby adopted by, this notice (Preliminary Decision Memorandum).

4.   See Antidumping Duties; Countervailing Duties, Final Rule,62 FR 27296, 27323 (May 19, 1997).

5.   See Initiation Notic e, 88 FR at 9482.

6.   See Memorandum, “Preliminary Scope Decision Memorandum, dated concurrently with this preliminary determination (Preliminary Scope Decision Memorandum).

7.   See Initiation Notic e, 88 FR at 9486.

8.   See Enforcement and Compliance's Policy Bulletin No. 05.1, regarding, “Separate-Rates Practice and Application of Combination Rates in Antidumping Investigations involving Non-Market Economy Countries,” (April 5, 2005) (Policy Bulletin 05.1), available at https://access.trade.gov/​Resources/​policy/​bull05-1.pdf.

9.   See19 CFR 351.309; see also19 CFR 351.303 (for general filing requirements).

10.   See Temporary Rule Modifying AD/CVD Service Requirements Due to COVID–19; Extension of Effective Period,85 FR 41363 (July 10, 2020).