Appendix B to Subpart P - Sloping and Benching

(a) Scope and application. This appendix contains specifications for sloping and benching when used as methods of protecting employees working in excavations from cave-ins. The requirements of this appendix apply when the design of sloping and benching protective systems is to be performed in accordance with the requirements set forth in § 1926.652(b)(2).

(b) Definitions.

Actual slope means the slope to which an excavation face is excavated.

Distress means that the soil is in a condition where a cave-in is imminent or is likely to occur. Distress is evidenced by such phenomena as the development of fissures in the face of or adjacent to an open excavation; the subsidence of the edge of an excavation; the slumping of material from the face or the bulging or heaving of material from the bottom of an excavation; the spalling of material from the face of an excavation; and ravelling, i.e., small amounts of material such as pebbles or little clumps of material suddenly separating from the face of an excavation and trickling or rolling down into the excavation.

Maximum allowable slope means the steepest incline of an excavation face that is acceptable for the most favorable site conditions as protection against cave-ins, and is expressed as the ratio of horizontal distance to vertical rise (H:V).

Short term exposure means a period of time less than or equal to 24 hours that an excavation is open.

(c) Requirements—(1) Soil classification. Soil and rock deposits shall be classified in accordance with appendix A to subpart P of part 1926.

(2) Maximum allowable slope. The maximum allowable slope for a soil or rock deposit shall be determined from Table B-1 of this appendix.

(3) Actual slope. (i) The actual slope shall not be steeper than the maximum allowable slope.

(ii) The actual slope shall be less steep than the maximum allowable slope, when there are signs of distress. If that situation occurs, the slope shall be cut back to an actual slope which is at least 1/2 horizontal to one vertical (1/2H:1V) less steep than the maximum allowable slope.

(iii) When surcharge loads from stored material or equipment, operating equipment, or traffic are present, a competent person shall determine the degree to which the actual slope must be reduced below the maximum allowable slope, and shall assure that such reduction is achieved. Surcharge loads from adjacent structures shall be evaluated in accordance with § 1926.651(i).

(4) Configurations. Configurations of sloping and benching systems shall be in accordance with Figure B-1.

EC30OC91.016 Figure B-1Slope Configurations(All slopes stated below are in the horizontal to vertical ratio)B-1.1Excavations made in Type A soil.1. All simple slope excavation 20 feet or less in depth shall have a maximum allowable slope of 3/4:1. EC30OC91.017 Simple Slope—GeneralException: Simple slope excavations which are open 24 hours or less (short term) and which are 12 feet or less in depth shall have a maximum allowable slope of 1/2:1. EC30OC91.018 Simple Slope—Short Term2. All benched excavations 20 feet or less in depth shall have a maximum allowable slope of 3/4 to 1 and maximum bench dimensions as follows: EC30OC91.019 Simple Bench EC30OC91.020 Multiple Bench3. All excavations 8 feet or less in depth which have unsupported vertically sided lower portions shall have a maximum vertical side of 31/2 feet. EC30OC91.021 Unsupported Vertically Sided Lower Portion—Maximum 8 Feet in DepthAll excavations more than 8 feet but not more than 12 feet in depth which unsupported vertically sided lower portions shall have a maximum allowable slope of 1:1 and a maximum vertical side of 31/2 feet. EC30OC91.022 Unsupported Vertically Sided Lower Portion—Maximum 12 Feet in DepthAll excavations 20 feet or less in depth which have vertically sided lower portions that are supported or shielded shall have a maximum allowable slope of 3/4:1. The support or shield system must extend at least 18 inches above the top of the vertical side. EC30OC91.023 Supported or Shielded Vertically Sided Lower Portion4. All other simple slope, compound slope, and vertically sided lower portion excavations shall be in accordance with the other options permitted under § 1926.652(b).B-1.2 Excavations Made in Type B Soil1. All simple slope excavations 20 feet or less in depth shall have a maximum allowable slope of 1:1. EC30OC91.024 Simple Slope2. All benched excavations 20 feet or less in depth shall have a maximum allowable slope of 1:1 and maximum bench dimensions as follows: EC30OC91.025 Single Bench EC30OC91.026 Multiple Bench3. All excavations 20 feet or less in depth which have vertically sided lower portions shall be shielded or supported to a height at least 18 inches above the top of the vertical side. All such excavations shall have a maximum allowable slope of 1:1. EC30OC91.027 Vertically Sided Lower Portion4. All other sloped excavations shall be in accordance with the other options permitted in § 1926.652(b).B-1.3 Excavations Made in Type C Soil1. All simple slope excavations 20 feet or less in depth shall have a maximum allowable slope of 11/2:1. EC30OC91.028 Simple Slope2. All excavations 20 feet or less in depth which have vertically sided lower portions shall be shielded or supported to a height at least 18 inches above the top of the vertical side. All such excavations shall have a maximum allowable slope of 11/2:1. EC30OC91.029 Vertical Sided Lower Portion3. All other sloped excavations shall be in accordance with the other options permitted in § 1926.652(b).B-1.4 Excavations Made in Layered Soils1. All excavations 20 feet or less in depth made in layered soils shall have a maximum allowable slope for each layer as set forth below. EC30OC91.030 EC30OC91.031 2. All other sloped excavations shall be in accordance with the other options permitted in § 1926.652(b).