02-5876. Special Conditions: Airbus Industrie, Model A340-500/-600 Airplanes; Ground Loads and Conditions for Center Landing Gear With Four Wheels and Braking Capability  

  • Start Preamble

    AGENCY:

    Federal Aviation Administration (FAA), DOT.

    ACTION:

    Notice of proposed special conditions.

    SUMMARY:

    This action proposes special conditions for Airbus Industrie Model A340-500 and -600 airplanes. These airplanes will have a novel or unusual design feature when compared to the state of technology envisioned in the airworthiness standards for transport category airplanes. This design feature is associated with the landing gear, in the form of a four-wheeled center landing gear, installed under the fuselage, which functions like a main landing gear in all respects, including the ability to brake. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These proposed special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

    DATES:

    Comments must be received on or before April 19, 2002.

    ADDRESSES:

    Comments on this proposal may be mailed in duplicate to: Federal Aviation Administration, Transport Airplane Directorate, Attn: Rules Docket (ANM-113), Docket No. NM211, 1601 Lind Avenue SW., Renton, Washington, 98055-4056; or delivered in duplicate to the Transport Airplane Directorate at the above address. Comments must be marked: Docket No. NM211. Comments may be inspected in the Rules Docket weekdays, except Federal holidays, between 7:30 a.m. and 4 p.m.

    Start Further Info

    FOR FURTHER INFORMATION CONTACT:

    Tim Backman, FAA, ANM-116, Transport Airplane Directorate, Aircraft Certification Service, 1601 Lind Avenue SW., Renton, Washington, 98055-4056; telephone (425) 227-2797; facsimile (425) 227-1149.

    End Further Info End Preamble Start Supplemental Information

    SUPPLEMENTARY INFORMATION:

    Comments Invited

    The FAA invites interested persons to participate in this rulemaking by submitting written comments, data, or views. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. We ask that you send us two copies of written comments.

    We will file in the docket all comments we receive, as well as a report summarizing each substantive public contact with FAA personnel concerning these proposed special conditions. The docket is available for public inspection before and after the comment closing date. If you wish to review the docket in person, go to the address in the ADDRESSES section of this preamble between 7:30 a.m. and 4 p.m., Monday through Friday, except Federal holidays.

    We will consider all comments we receive on or before the closing date for comments. We will consider comments filed late if it is possible to do so without incurring expense or delay. We may change this proposal for special conditions in light of the comments we receive.

    If you want the FAA to acknowledge receipt of your comments on this proposal, include with your comments a pre-addressed, stamped postcard on which the docket number appears. We will stamp the date on the postcard and mail it back to you.

    Background

    On November 14, 1996, Airbus Industrie applied for an amendment to U.S. type certificate (TC) A43NM to include the new models A340-500 and -600. These models are derivatives of the A340-300, which is approved under the same TC.

    The Model A340-500 fuselage is a 6-frame stretch of the Model A340-300 and is powered by 4 Rolls Royce Trent 553 engines, each rated at 53,000 pounds of thrust. The airplane has interior seating arrangements for up to 375 passengers, with a maximum takeoff weight (MTOW) of 820,000 pounds. The Model 340-500 is intended for long-range operations and has additional fuel capacity over that of the model A340-600.

    The Model A340-600 fuselage is a 20-frame stretch of the Model A340-300 and is powered by 4 Rolls Royce Trent 556 engines, each rated at 56,000 pounds of thrust. The airplane has interior seating arrangements for up to 440 passengers, with a MTOW of 804,500 pounds.

    Type Certification Basis

    Under the provisions of 14 CFR 21.101, Airbus Industrie must show that the Model A340-500 and -600 airplanes Start Printed Page 12904meet the applicable provisions of the regulations incorporated by reference in TC A43NM or the applicable regulations in effect on the date of application for the change to the type certificate. The regulations incorporated by reference in the type certificate are commonly referred to as the “original type certification basis.” The regulations incorporated by reference in TC A43NM are 14 CFR part 25, effective February 1, 1965, including Amendments 25-1 through 25-63, and Amendments 25-64, 25-65, 25-66, and 25-77, with certain exceptions that are not relevant to these proposed special conditions.

    In addition, if the regulations incorporated by reference do not provide adequate standards with respect to the change, the applicant must comply with certain regulations in effect on the date of application for the change. The FAA has determined that the Model A340-500 and -600 airplanes must be shown to comply with Amendments 25-1 through 25-91 to part 25, with certain FAA-allowed reversions for specific part 25 regulations to the part 25 amendment levels of the original type certification basis.

    Airbus has also chosen to comply with part 25 as amended by Amendments 25-92, -93, -94, -95, -97, -98, and -104.

    If the Administrator finds that the applicable airworthiness regulations (i.e., part 25 as amended) do not contain adequate or appropriate safety standards for the Airbus Industrie Model A340-500 and -600 because of a novel or unusual design feature, special conditions are prescribed under the provisions of 14 CFR 21.16.

    In addition to the applicable airworthiness regulations and special conditions, the Airbus Industrie Model A340-500 and -600 must comply with the fuel vent and exhaust emission requirements of 14 CFR part 34 and the noise certification requirements of 14 CFR part 36.

    Special conditions, as defined in 14 CFR 11.19, are issued in accordance with § 11.38 and become part of the type certification basis in accordance with § 21.101(b)(2).

    Special conditions are initially applicable to the model for which they are issued. Should the type certificate for that model be amended later to include any other model that incorporates the same novel or unusual design feature, or should any other model already included on the same type certificate be modified to incorporate the same novel or unusual design feature, the special conditions would also apply to the other model under the provisions of § 21.101(a)(1).

    Novel or Unusual Design Features

    The Airbus Models A340-500 and -600 will incorporate the following novel or unusual design feature: a four-wheel center landing gear with braking ability.

    Discussion

    The basic A340 included a two-wheel center landing gear which did not have brakes. The purpose of the center landing gear was to assist the main landing gear during ground handling conditions for heavy airplane weights. This center landing gear was not intended for energy absorption during landing, even if it could participate in the impact under certain conditions. Therefore, to provide additional taxi, takeoff, and landing criteria for this arrangement, Special Conditions 25-ANM-69 was issued.

    The Model A340-500 and -600 airplanes have a four-wheel center landing gear which functions in all respects like a main landing gear, including braking capabilities. Because the speeds and weights of the Models A340-500 and -600 are greater than that of the basic A340, redesign of the center landing gear was necessary. As a result, the current rules, applying to the original two-wheel center landing gear, are inadequate.

    Applicability

    As discussed above, these special conditions are applicable to the Airbus Models A340-500 and -600. Should Airbus Industries apply at a later date for a change to the type certificate to include another model incorporating the same novel or unusual design feature, the special conditions would apply to that model as well under the provisions of § 21.101(a)(1).

    Conclusion

    This action affects only certain novel or unusual design features of the center landing gear on the Model A340-500 and A340-600 airplanes. It is not a rule of general applicability, and it affects only the applicant who applied to the FAA for approval of these features on the airplane.

    Start List of Subjects

    List of Subjects in 14 CFR Part 25

    • Aircraft
    • Aviation safety
    • Reporting and recordkeeping requirements
    End List of Subjects

    The authority citation for these special conditions is as follows:

    Start Authority

    Authority: 49 U.S.C. 106(g), 40113, 44701, 44702, 44704.

    End Authority

    The Proposed Special Conditions

    Accordingly, the Federal Aviation Administration (FAA) proposes the following special conditions as part of the type certification basis for Airbus Model A340-500 and A340-600 airplanes.

    The following special conditions are proposed in lieu of the previously issued special conditions, “Ground Load Conditions for Center Landing Gear,” recorded as item 10 of Special Conditions: Airbus Industrie Model A340 Series Airplanes [Docket No. NM-75, Special Conditions No. 25-ANM-69]:

    1. Ground Load Conditions for Center Landing Gear. Notwithstanding § 25.477, the requirements of § 25.473 and §§ 25.479 through 25.485 apply, except as noted:

    (a) In addition to the requirements of § 25.473, “Landing load conditions and assumptions,” and § 25.479, “Level landing conditions,” landing should be considered on a level runway and on a runway having a convex upward shape that may be approximated by a slope of 1.5 percent at main landing gear stations. The maximum loads determined from these two conditions must be applied to each main landing gear and to the center landing gear.

    (b) In addition to the requirements of § 25.483, “One gear landing conditions,” the condition represented by Figure 1 also applies:

    Start Printed Page 12905

    Start Printed Page 12906

    (c) In lieu of the requirements of § 25.485, “Side load conditions,” the following apply:

    (1) The airplane is considered to be in the level attitude with only the main and center wheels contacting the ground.

    (2) Vertical reactions of one-half of the maximum vertical reaction obtained at each main and center gear in the level landing conditions should be considered. The vertical loads must be combined with side loads as follows: for the main gear, 0.8 of the vertical reaction (on one side) acting inward and 0.6 of the vertical reaction (on the other side) acting outward; for the center gear, 0.7 of the vertical reaction acting in the same direction as main gear side loads. These loads are assumed to be applied at the ground contact point and to be resisted by the inertia of the airplane. The drag loads may be assumed to be zero.

    (d) In addition to § 25.489, “Ground handling conditions,” the airplane should be considered to be on a level runway and on a runway having a convex upward shape that may be approximated by a slope of 1.5 percent at main landing gear stations. The ground reactions must be distributed to the individual landing gear units in a rational or conservative manner.

    (e) In addition to the requirements of § 25.493(d), “Braked roll conditions,” the sudden application of maximum braking effort must be defined taking into account the behavior of the braking system. Failure conditions of the braking system not shown to be extremely improbable must be analyzed in accordance with the following criteria:

    (1) At the time of occurrence. A realistic scenario, including pilot corrective actions, must be established to determine the loads occurring at the time of failure and immediately after failure.

    (i) For static strength substantiation, these loads multiplied by an appropriate factor of safety that is related to the probability of occurrence of the failure are ultimate loads to be considered for design. The factor of safety (F.S.) is defined in Figure 2.

    (ii) For residual strength substantiation, the airplane must be able to withstand two thirds of the ultimate loads defined in paragraph (e)(1)(i).

    (iii) Failures of the system that result in forced structural vibrations (oscillatory failures) must not produce loads that could result in detrimental deformation of primary structure.

    (2) Consideration of certain failure conditions may be required by other sections of part 25, regardless of calculated system reliability. Where analysis shows the probability of these failure conditions to be less than 10−9, criteria other than those specified in this paragraph may be used for structural substantiation to show continued safe flight and landing.

    (3) Warning considerations. For system failure detection and warning, the system must be checked for failure conditions, not extremely improbable, that degrade the structural capability below the level required by part 25 or significantly reduce the reliability of the remaining system. The flightcrew must be made aware of these failures before flight. Certain elements of the control system, such as mechanical and hydraulic components, may use special periodic inspections, and electronic components may use daily checks, in lieu of warning systems to achieve the objective of this requirement. These certification maintenance requirements must be limited to components that are not readily detectable by normal warning systems and where service history shows that inspections will provide an adequate level of safety.

    (4) Dispatch with known failure conditions. If the airplane is to be dispatched in a known system failure condition that affects structural Start Printed Page 12907performance, or affects the reliability of the remaining system to maintain structural performance, then the provisions of these special conditions must be met for the dispatched condition and for subsequent failures. Flight limitations and expected operational limitations may be taken into account in establishing Qj as the combined probability of being in the dispatched failure condition and the subsequent failure condition for the safety margins in Figure 3. These limitations must be such that the probability of being in this combined failure state and then subsequently encountering limit load conditions is extremely improbable. No reduction in these safety margins is allowed if the subsequent system failure rate is greater than 10−3 per hour.”

    Q j = (T j)(P j) where:

    T j = Average time spent in failure condition j (in hours).

    P j = Probability of occurrence of failure mode j (per hour).

    (f) In lieu of the requirements of § 25.495, “Turning,” the following apply:

    (1) The airplane is assumed to execute a steady turn by nose gear steering, or by application of sufficient differential power, so that the limit load factors applied at the center of gravity are 1.0 vertically and 0.5 laterally.

    (2) The airplane must be designed for the condition prescribed in paragraph (f)(1), taking into account:

    (i) The effects of tire characteristics on the sharing of lateral loads on each tire of the landing gear system, and

    (ii) The effect of airframe and landing gear flexibility on the sharing of loads on the different legs of the landing gear system.

    (g) In lieu of the requirements of § 25.503, “Pivoting,” the following apply:

    (1) The main and center gear units and supporting structure must be designed for the scrubbing or torsion loads, or both, induced by pivoting during ground maneuvers produced by:

    (i) Towing at the nose gear, no brakes applied, and

    (ii) Application of symmetrical or unsymmetrical forward thrust to aid pivoting and with or without braking by pilot action on the pedals.

    (2) The airplane is assumed to be in static equilibrium, with the loads being applied at the ground contact points.

    (3) The limit vertical load factor must be 1.0, and:

    (i) For wheels with locked brakes applied by pilot action on the pedals, the coefficient of friction must be 0.8.

    (ii) For wheels with brakes not applied, the ground tire reactions must be based on reliable tire data.

    (4) The failure conditions must be analyzed in accordance with paragraph (e) of these Special Conditions.

    (h) In lieu of paragraph (b) of § 25.723 “Shock absorption tests,” the center landing gear should not fail in a test demonstrating its reserve energy absorption capacity at design landing weight, assuming airplane lift no greater than the airplane weight acting during a 12-feet-per-second airplane landing impact, taking into account both main and center gear acting during the impact. Landing should be considered on a level runway or a runway having a convex upward shape that may be approximated by a slope of 1.5 percent with the horizontal at main landing gear stations, whichever is the most critical.

    Start Signature

    Issued in Renton, Washington, on February 28, 2002.

    Vi L. Lipski,

    Manager, Transport Airplane Directorate, Aircraft Certification Service.

    End Signature End Supplemental Information

    BILLING CODE 4910-13-P

    BILLING CODE 4910-13-P

    [FR Doc. 02-5876 Filed 3-19-02; 8:45 am]

    BILLING CODE 4910-13-P

Document Information

Published:
03/20/2002
Department:
Federal Aviation Administration
Entry Type:
Proposed Rule
Action:
Notice of proposed special conditions.
Document Number:
02-5876
Dates:
Comments must be received on or before April 19, 2002.
Pages:
12903-12907 (5 pages)
Docket Numbers:
Docket No. NM211, Notice No. 25-02-03-SC
Topics:
Aircraft, Aviation safety, Reporting and recordkeeping requirements
PDF File:
02-5876.pdf
CFR: (1)
14 CFR 25