[Federal Register Volume 64, Number 140 (Thursday, July 22, 1999)]
[Rules and Regulations]
[Pages 39398-39403]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 99-18683]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. 97-SW-59-AD; Amendment 39-11235; AD 99-15-14]
RIN 2120-AA64
Airworthiness Directives; Sikorsky Aircraft-Manufactured Model
CH-54B Helicopters
AGENCY: Federal Aviation Administration, DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: This amendment adopts a new airworthiness directive (AD),
applicable to Sikorsky Aircraft-manufactured Model CH-54B helicopters,
that requires initial and recurring inspections and rework or
replacement, if necessary, of the second stage lower planetary plate
(plate). This amendment is prompted by two reports of cracked plates
that have been found during overhaul and inspections. The actions
specified by this AD are intended to prevent failure of the main
gearbox plate due to fatigue cracking, which could lead to failure of
the main gearbox and subsequent loss of control of the helicopter.
EFFECTIVE DATE: August 26, 1999.
FOR FURTHER INFORMATION CONTACT: Uday Garadi, Aerospace Engineer, FAA,
Rotorcraft Directorate, Rotorcraft Certification Office, Fort Worth,
Texas 76193-0170, telephone (817) 222-5157, fax (817) 222-5959.
SUPPLEMENTARY INFORMATION: A proposal to amend part 39 of the Federal
Aviation Regulations (14 CFR part 39) to include an airworthiness
directive (AD) that is applicable to Sikorsky Aircraft-manufactured
Model CH-54B helicopters was published in the Federal Register on April
16, 1999 (64 FR 18835). That action proposed to require initial and
recurring inspections, and rework or replacement, if necessary, of the
plate.
Interested persons have been afforded an opportunity to participate
in the making of this amendment. No comments were received on the
proposal or the FAA's determination of the cost to the public. The FAA
has determined that air safety and the public interest require the
adoption of the rule as proposed.
The FAA estimates that 4 helicopters of U.S. registry will be
affected by this AD, that it will take approximately 8 work hours per
helicopter to accomplish the borescope inspection, 1 work hour to
inspect the main gearbox oil filter pack, 140 work hours to remove and
replace the main gearbox assembly, if necessary, and 20 work hours to
rework the plate, and that the average labor rate is $60 per work hour.
Required parts will cost approximately $8,000 per helicopter. Based on
these figures, the total cost impact of the AD on U.S. operators is
estimated to be $67,760; $2,160 to accomplish the initial inspections
and $65,600 to replace the plate in the main gearbox assembly in all 4
helicopters, if necessary. Daily preflight inspections of the main
gearbox oil filter pack will cost $60 per helicopter for each day
flight is conducted.
The regulations adopted herein will not have substantial direct
effects on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, in
accordance with Executive Order 12612, it is determined that this final
rule does not have sufficient federalism implications to warrant the
preparation of a Federalism Assessment.
For the reasons discussed above, I certify that this action (1) is
not a ``significant regulatory action'' under Executive Order 12866;
(2) is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and (3) will not have a
significant economic impact, positive or negative, on a substantial
number of small entities under the criteria of the Regulatory
Flexibility Act. A final evaluation has been prepared for this action
and it is contained in the Rules Docket. A copy of it may be obtained
from the Rules Docket at the Office of the Regional Counsel, Southwest
Region, 2601 Meacham Blvd., Room 663, Fort Worth, Texas 76137.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
Adoption of the Amendment
Accordingly, pursuant to the authority delegated to me by the
[[Page 39399]]
Administrator, the Federal Aviation Administration amends part 39 of
the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. Section 39.13 is amended by adding a new airworthiness directive
to read as follows:
AD 99-15-14 Blue Bird Helicopters: Amendment 39-11235. Docket No.
97-SW-59-AD.
Applicability: CH-54B helicopters with main gearbox second stage
lower planetary plate (plate), part number (P/N) 6435-20516-101,
installed, certificated in any category.
Note 1: This AD applies to each helicopter identified in the
preceding applicability provision, regardless of whether it has been
otherwise modified, altered, or repaired in the area subject to the
requirements of this AD. For helicopters that have been modified,
altered, or repaired so that the performance of the requirements of
this AD is affected, the owner/operator must request approval for an
alternative method of compliance in accordance with paragraph (c) of
this AD. The request should include an assessment of the effect of
the modification, alteration, or repair on the unsafe condition
addressed by this AD; and, if the unsafe condition has not been
eliminated, the request should include specific proposed actions to
address it.
Compliance: Required as indicated, unless accomplished
previously.
To prevent failure of the plate due to fatigue cracking, which
could lead to failure of the main gearbox and subsequent loss of
control of the helicopter, accomplish the following:
(a) For main gearbox assemblies containing plate, part number
(P/N) 6435-20516-101, with 1,600 or more hours time-in-service
(TIS):
Note 2: If the TIS hours of the plate is not known, use the main
gearbox assembly's total operating time.
(1) Prior to the first flight of each day, inspect the main oil
filter for magnesium contamination. If magnesium contamination is
discovered, replace the main gearbox assembly.
(2) Within the next 100 hours TIS after the effective date of
this AD, and thereafter at intervals not to exceed 200 hours TIS,
conduct a borescope inspection of the plate for cracks in the area
of the nine lightening holes (see Figure 1). If a crack is found,
replace the plate with an airworthy plate. The plate, P/N 6435-
20516-101, is part of the main gearbox second stage planetary set
(P/N 6435-20514-041), which is a serialized matched set, and must be
replaced as a set.
BILLING CODE 4910-13-P
[[Page 39400]]
[GRAPHIC] [TIFF OMITTED] TR22JY99.017
BILLING CODE 4910-13-C
[[Page 39401]]
(b) At the next overhaul of the main gearbox assembly, inspect
and rework the plate, P/N 6435-20516-101, as follows:
(1) Fluorescent magnetic particle inspect the plate per ASTM
E1444 in circumferential and longitudinal directions using a wet
continuous method. Pay particular attention to the area around the
nine 1.750-inch diameter lightening holes.
(2) If a crack is found, the plate is unairworthy. Replace it
with an airworthy plate.
(3) If no crack is found, rework the plate as follows, ensuring
that all plate surfaces are free of any crack, scratch, dent, or
corrosion.
(i) Measuring from the center of each 1.750-inch diameter
lightening hole, machine 0.015/0.020 inch from the radius of the
hole (see Figure 2). Machined surface roughness shall not exceed 63
microinches AA rating.
BILLING CODE 4910-13-P
[[Page 39402]]
[GRAPHIC] [TIFF OMITTED] TR22JY99.018
BILLING CODE 4910-13-C
[[Page 39403]]
(ii) Apply a 0.030/0.050-inch radius on the top and bottom edge
of each hole.
(4) Fluorescent magnetic particle inspect the reworked areas per
ASTM E1444 in circumferential and longitudinal directions using a
wet continuous method.
(5) If a crack is found, the plate is unairworthy. Replace it
with an airworthy plate.
(6) If no crack is found, rework the plate as follows:
(i) Remove the protective finish from the specified areas on the
top and bottom of the plate as follows:
(A) Mask the top and bottom of the plate leaving exposed a 3.20-
inch minimum circumferential band centered on 13.75-inch diameter of
plate (see Figure 2). Mask the area to protect the thrust washer and
the surrounding areas from vapor blast.
(B) Using a vapor blast machine, remove the protective finish
from the exposed circumferential band on the top and bottom of the
plate. Use No. 220 aluminum oxide grit at a pressure of 80-90 pounds
per square inch.
(ii) Shot peen the specified areas on the plate by remasking the
top and bottom of the plate leaving exposed the 3.20-inch minimum
circumferential band centered on 13.75-inch diameter of the plate.
Mask the area to protect the thrust washer and the surrounding areas
from the shot peening process.
(iii) Shot peen the inside diameter of the lightening holes and
the upper and lower surfaces of the plate in the 3.20-inch minimum
circumferential band to 0.008 to 0.012A intensity, ensuring 200%
coverage per MIL-S-13165C or latest revision. Use cast steel shot,
size 170. Use a tracer dye inspection method.
Note 3: Overspray is permitted to allow a feathering application
during the peening process from the peened surface to the non-peened
surface.
(iv) Finish the reworked surfaces as follows:
(A) Clean the surfaces thoroughly with acetone (Fed. Spec O-A-
51, or equivalent).
(B) Apply Presto black or blueing touchup solution to the
reworked surfaces with cotton swabs. The solution temperature must
be between 21 deg. C and 49 deg. C (70 deg. F to 120 deg. F). Keep
the surfaces wet for about three minutes to get a uniform dark
color.
(C) Rinse the surface in cold running water and dry with forced
air.
Note 4: A hot water rinse may be used after the cold water rinse
to speed up drying time.
(D) Using steel wool, Grade 00 or finer, rub the surfaces
lightly. Polish with a soft cloth and then coat with a preservative
oil (MIL-C-15074).
(v) Identify the reworked plate by stamping the number of this
AD after the part number. Use a low-stress depth-controlled
impression-stamp with full fillet depth of no more than 0.003 inch
(see Figure 2). Marking must be such that it cannot be construed as
part of the part number.
(c) An alternative method of compliance or adjustment of the
compliance time that provides an acceptable level of safety may be
used if approved by the Manager, Rotorcraft Certification Office,
FAA, Rotorcraft Directorate. Operators shall submit their requests
through an FAA Principal Maintenance Inspector, who may concur or
comment and then send it to the Manager, Rotorcraft Certification
Office.
Note 5: Information concerning the existence of approved
alternative methods of compliance with this AD, if any, may be
obtained from the Rotorcraft Certification Office.
(d) Special flight permits may be issued in accordance with
sections 21.197 and 21.199 of the Federal Aviation Regulations (14
CFR 21.197 and 21.199) to operate the helicopter to a location where
the requirements of this AD can be accomplished.
(e) This amendment becomes effective on August 26, 1999.
Issued in Fort Worth, Texas, on July 15, 1999.
Henry A. Armstrong,
Manager, Rotorcraft Directorate, Aircraft Certification Service.
[FR Doc. 99-18683 Filed 7-21-99; 8:45 am]
BILLING CODE 4910-13-P
