[Federal Register Volume 60, Number 244 (Wednesday, December 20, 1995)]
[Rules and Regulations]
[Pages 65516-65519]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 95-30771]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. 95-SW-28-AD; Amendment 39-9467; AD 95-26-09]
Airworthiness Directives; Sikorsky Aircraft-manufactured Model
CH-34A, CH-34C, H-34A, HH-34J, HSS-1, HSS-1N, HUS-1, SH-34J, UH-34D,
UH-34E, and UH-34J Helicopters
AGENCY: Federal Aviation Administration, DOT.
ACTION: Final rule; request for comments.
-----------------------------------------------------------------------
SUMMARY: This amendment adopts a new airworthiness directive (AD) that
is
[[Page 65517]]
applicable to Sikorsky Aircraft-manufactured Model CH-34A, CH-34C, H-
34A, HH-34J, HSS-1, HSS-1N, HUS-1, SH-34J, UH-34D, UH-34E, and UH-34J
helicopters. This action requires initial and repetitive magnetic
particle inspections of the main rotor shaft (shaft) for cracks, and
defines power limitations for certain helicopter operations. This
amendment is prompted by a recent accident in which a shaft failed,
resulting in loss of power. Subsequent inspections on other aircraft of
the same type revealed cracks in four additional shafts. The actions
specified in this AD are intended to prevent failure of the shaft, loss
of power to the rotor system, and subsequent loss of control of the
helicopter.
DATES: Effective January 4, 1996. -
Comments for inclusion in the Rules Docket must be received on or
before February 20, 1996.
ADDRESSES: Submit comments in triplicate to the Federal Aviation
Administration (FAA), Office of the Assistant Chief Counsel, Attention:
Rules Docket No. 95-SW-28-AD, 2601 Meacham Blvd., Room 663, Fort Worth,
Texas 76137.
FOR FURTHER INFORMATION CONTACT: Mr. Francis X. Walsh, Aerospace
Engineer, FAA, Boston Aircraft Certification Office, 12 New England
Executive Park, Burlington, Massachusetts 01803-5299, telephone (617)
238-7158, fax (617) 238-7199.
SUPPLEMENTARY INFORMATION: This amendment adopts a new AD that is
applicable to Sikorsky Aircraft-manufactured Model CH-34A, CH-34C, H-
34A, HH-34J, HSS-1, HSS-1N, HUS-1, SH-34J, UH-34D, UH-34E, and UH-34J
helicopters with shaft assembly, part number (P/N) S1635-20059-2,
installed. This AD is prompted by an accident in which the failure of a
shaft resulted in the crash of a helicopter. Since that accident,
inspections have revealed cracks in four additional shafts. The shaft
transmits power to the main rotor system to provide lift for the
helicopter. Failure of this shaft results in loss of power to the main
rotor system and subsequent loss of control of the helicopter. Due to
the criticality of the shaft, this AD must be issued immediately to
correct an unsafe condition in the affected helicopters. -
Since an unsafe condition has been identified that is likely to
exist or develop on other Sikorsky Aircraft-manufactured Model CH-34A,
CH-34C, H-34A, HH-34J, HSS-1, HSS-1N, HUS-1, SH-34J, UH-34D, UH-34E,
and UH-34J helicopters of the same type design, this AD is being issued
to prevent failure of the shaft, loss of power to the rotor system, and
subsequent loss of control of the helicopter. This AD requires
determining the operational cycles-per-hour on the helicopter, removing
the shaft assembly from the main gear box, and inspecting the shaft for
cracks using a magnetic particle inspection method within the next 50
hours time-in-service (TIS). Following this initial inspection,
repetitive magnetic particle inspections are required. Additionally,
this AD prescribes operating limitations for certain helicopter
operations. -
Since a situation exists that requires the immediate adoption of
this regulation, it is found that notice and opportunity for prior
public comment hereon are impracticable, and that good cause exists for
making this amendment effective in less than 30 days.
Comments Invited -
Although this action is in the form of a final rule that involves
requirements affecting flight safety and, thus, was not preceded by
notice and an opportunity for public comment, comments are invited on
this rule. Interested persons are invited to comment on this rule by
submitting such written data, views, or arguments as they may desire.
Communications should identify the Rules Docket number and be submitted
in triplicate to the address specified under the caption ADDRESSES. All
communications received on or before the closing date for comments will
be considered, and this rule may be amended in light of the comments
received. Factual information that supports the commenter's ideas and
suggestions is extremely helpful in evaluating the effectiveness of the
AD action and determining whether additional rulemaking action would be
needed. -
Comments are specifically invited on the overall regulatory,
economic, environmental, and energy aspects of the rule that might
suggest a need to modify the rule. All comments submitted will be
available, both before and after the closing date for comments, in the
Rules Docket for examination by interested persons. A report that
summarizes each FAA-public contact concerned with the substance of this
AD will be filed in the Rules Docket. -
Commenters wishing the FAA to acknowledge receipt of their comments
submitted in response to this rule must submit a self-addressed,
stamped postcard on which the following statement is made: ``Comments
to Docket No. 95-SW-28-AD.'' The postcard will be date stamped and
returned to the commenter. -
The regulations adopted herein will not have substantial direct
effects on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, in
accordance with Executive Order 12612, it is determined that this final
rule does not have sufficient federalism implications to warrant the
preparation of a Federalism Assessment. -
The FAA has determined that this regulation is an emergency
regulation that must be issued immediately to correct an unsafe
condition in aircraft, and that it is not a ``significant regulatory
action'' under Executive Order 12866. It has been determined further
that this action involves an emergency regulation under DOT Regulatory
Policies and Procedures (44 FR 11034, February 26, 1979). If it is
determined that this emergency regulation otherwise would be
significant under DOT Regulatory Policies and Procedures, a final
regulatory evaluation will be prepared and placed in the Rules Docket.
A copy of it, if filed, may be obtained from the Rules Docket at the
location provided under the caption ADDRESSES.
List of Subjects in 14 CFR Part 39 -
Air transportation, Aircraft, Aviation safety, Safety.
Adoption of the Amendment -
Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration amends part 39 of
the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES -
1. The authority citation for part 39 continues to read as follows:
-Authority: 49 USC 106(g), 40101, 40113, 44701.
Sec. 39.13 [Amended] -
2. Section 39.13 is amended by adding a new airworthiness directive
to read as follows:
AD 95-26-09 Federico Helicopters; Invest in Opportunities, Inc.;
Orlando Helicopter Airways; Consolidated Air Crane, Inc.; and
Pacific Aviation, Inc.: Amendment 39-9467. Docket No. 95-SW-28-AD
-Applicability: Sikorsky Aircraft-manufactured Model CH-34A,
CH-34C, H-34A, HH-34J, HSS-1, HSS-1N, HUS-1, SH-34J, UH-34D, UH-34E,
and UH-34J helicopters with main rotor shaft assembly (shaft
assembly), part number (P/N) S1635-20059-2, installed, certificated
in any category.
-
[[Page 65518]]
Note 1: The shaft assembly consists of a main rotor shaft, P/N
S1635-20059; an upper end plug, P/N S1635-20153; and a lower end
plug, P/N S1635-20154. The shaft assembly P/N (S1635-20059-2) is
marked on the edge of the main rotor shaft lower flange. -
Note 2: This AD applies to each helicopter identified in the
preceding applicability provision, regardless of whether it has been
modified, altered, or repaired in the area subject to the
requirements of this AD. For helicopters that have been modified,
altered, or repaired so that the performance of the requirements of
this AD is affected, the owner/operator must use the authority
provided in paragraph (j) to request approval from the FAA. This
approval may address either no action, if the current configuration
eliminates the unsafe condition, or different actions necessary to
address the unsafe condition described in this AD. Such a request
should include an assessment of the effect of the changed
configuration on the unsafe condition addressed by this AD. In no
case does the presence of any modification, alteration, or repair
remove any helicopter from the applicability of this AD.
-Compliance: Required as indicated, unless accomplished
previously. -
To prevent failure of the main rotor shaft (shaft), loss of
power to the rotor system, and subsequent loss of control of the
helicopter, accomplish the following: -
(a) From available helicopter records, determine the maximum
number of actual operational cycles-per-hour of the current shaft
assembly since installation. An operational cycle is defined as one
turnaround (external lift cycle) for external load operations, and
as one takeoff and one landing for internal load operations. A
turnaround is defined as picking up an external load, transporting
that load to a drop-off point, releasing the load, and flying to the
next load pickup point. If the maximum number of actual operational
cycles-per-hour cannot be determined, use 25-operational cycles-per-
hour as the maximum operational cycles-per-hour for purposes of this
AD. Record the determined number of operational usage cycles-per-
hour of the shaft assembly in the appropriate aircraft maintenance
records. -
(1) If the maximum operational cycles-per-hour has ever equaled
or exceeded 20 cycles-per-hour, inspect in accordance with paragraph
(b) of this AD within the next 50 hours time-in-service (TIS),
unless previously accomplished within the last 200 hours TIS. -
(2) If the maximum operational cycles-per-hour has never
exceeded 19 cycles-per-hour, inspect the shaft in accordance with
paragraph (b) of this AD within the next 50 hours TIS, unless
previously accomplished. -
(b) Remove the shaft assembly, P/N S1635-20059-2, from the main
gear box. Remove the upper end plug, P/N S1635-20153, and lower end
plug, P/N S1635-20154, from the shaft assembly, and conduct a
magnetic particle inspection (MPI) of the shaft for cracks in
accordance with MIL-STD-1949 or ASTM E-1444. Pay particular
attention to the inside diameter of the 0.7515 - 0.7510-inch
diameter dowel pin holes in the flange and adjacent flange surfaces.
-Note 3: Section 2D of Sikorsky Aircraft Alert Service Bulletin
58B35-34, dated June 9, 1995, contains a procedure for conducting a
MPI of the shaft (in agreement with MIL-STD-1949 or ASTM E-1444).
-(c) Conduct repetitive MPI's of the shaft for cracks as
follows: -
(1) If the maximum operational cycles-per-hour has ever equaled
or exceeded 20 cycles-per-hour, repeat the MPI at intervals not to
exceed 250 hours TIS from the date of the last inspection. -
(2) If the maximum operational cycles-per-hour exceeds 6 cycles-
per-hour, but has always been less than 20 cycles-per-hour, repeat
the MPI at 1,250 hours TIS, and thereafter at intervals not to
exceed 250 hours TIS from the date of the last inspection. If the
last inspection was accomplished between 1,000 hours TIS and 1,250
hours TIS, begin the repetitive inspections within 250 hours TIS
from the date of the last inspection instead of at 1,250 hours TIS.
-
(3) If the maximum operational cycles-per-hour has never
exceeded 6 cycles-per-hour, repeat the MPI at 1,250 hours TIS. If
the last inspection was accomplished between 1,000 hours TIS and
1,250 hours TIS, repeat the MPI within 250 hours TIS from the date
of the last inspection instead of at 1,250 hours TIS. -
(d) Report all inspection results to the Manager, Boston
Aircraft Certification Office, using the Attachment provided later
in this AD. Reporting requirements have been approved by the Office
of Management and Budget and assigned OMB control number 2120-0056.
-
(e) If no crack is discovered, replace the upper and lower end
plugs into the shaft and reinstall the shaft assembly into the main
gearbox. -
(f) If any crack is discovered or on or before the shaft
assembly reaches 2,500 hours TIS, replace the shaft assembly with an
airworthy shaft assembly, P/N S1635-20059-2. If the replacement
shaft has previously been in service, determine the maximum
operational cycles-per-hour in accordance with paragraph (a) and
inspect in accordance with this AD.
-Note 4: In accordance with the applicable maintenance manual,
2,500 hours TIS is the mandatory retirement life for the shaft
assembly, P/N S1635-20059-2.
-(g) If the main rotor shaft assembly installed on the
helicopter has ever equaled or exceeded 20 or more operational
cycles-per-hour, insert the following restrictions into the
Limitations section of the Rotorcraft Flight Manual: -
(1) For turbine engine installations: ``The main rotor shaft
assembly installed on this helicopter has been operated at 20 or
more cycles-per-hour. Engine power is restricted to maximum
continuous power at 93%Nf. Takeoff power operations are
prohibited.'' -
(2) For reciprocating engine installations: ``The main rotor
shaft assembly installed on this helicopter has been operated at 20
or more cycles-per-hour. Engine power is restricted to maximum
continuous power at 2,500 RPM. Takeoff power operations are
prohibited.'' -
(h) If the main rotor shaft assembly installed on the helicopter
has ever equaled or exceeded 20 or more operational cycles-per-hour,
install on the instrument panel, adjacent to the pilot's engine
(Nf or RPM) tachometer, torquemeter, or manifold pressure
gauges, a placard made of material that is not easily erased,
disfigured, or obscured that contains the following statement in
lettering of 0.2 inch minimum height and stated in one or two lines:
-
(1) For turbine engine installations: -
``MAX PWR: 101% Q AT 93% Nf'' -
(2) For reciprocating engine installations: -
``MAX PWR: 47.5 IN. HG AT 2,500 RPM'' -
(i) Continue to record operational cycles-per-hour of the shaft
assembly in the appropriate maintenance records. If operational
cycles-per-hour increases on an affected shaft assembly to the
extent that it places the shaft assembly into a higher cycles-per-
hour usage group, the applicable requirements and limitations
contained in this AD for the higher usage group apply to that shaft
assembly. A replacement shaft assembly must comply with all
requirements and limitations of this AD as applicable. If the number
of operational cycles-per-hour determined for a replacement shaft
assembly does not equal or exceed 20 cycles-per-hour, the Rotorcraft
Flight Manual limitation specified in paragraph (g) and the placard
required by paragraph (h) may be removed.
-Note 5: Information concerning the existence of approved
alternative methods of compliance with this AD, if any, may be
obtained from the Boston Aircraft Certification Office.
-(j) An alternative method of compliance or adjustment of the
compliance time that provides an acceptable level of safety may be
used when approved by the Manager, Boston Aircraft Certification
Office, FAA, New England Region. Operators shall submit their
requests through an FAA Principal Maintenance Inspector, who may
concur or comment and then send it to the Manager, Boston Aircraft
Certification Office. -
(k) Special flight permits may be issued in accordance with
sections 21.197 and 21.199 of the Federal Aviation Regulations (14
CFR 21.197 and 21.199) to operate the helicopter to a location where
the requirements of this AD can be accomplished.
(l) This amendment becomes effective on January 4, 1996.
Attachment
Inspection Results Report
The following information must be reported as soon as possible,
but no later than 7 days after inspection, to: Manager, Boston
Aircraft Certification Office, Engine and Propeller Directorate,
Aircraft Certification Service, Federal Aviation Administration, 12
New England Executive Park, Burlington, MA 01803-5299, FAX: (617)
238-7199.
Operator/Repair Station------------------------------------------------
Aircraft Model No.-----------------------------------------------------
Aircraft Serial No.----------------------------------------------------
Date of Inspection-----------------------------------------------------
Main Rotor Part No.----------------------------------------------------
Main Rotor Serial No.--------------------------------------------------
Type of Aircraft Utilization:
Passenger Carry------------------------------------------------------
Firefighting---------------------------------------------------------
Utility/Construction-------------------------------------------------
Logging--------------------------------------------------------------
Other----------------------------------------------------------------
[[Page 65519]]
-----------------------------------------------------------------------
Identify Operational Usage Cycles-Per-Hour:
1-6 Operational
Cycles-Per-Hour----------------------------------------------------
7-19 Operational
Cycles-Per-Hour----------------------------------------------------
20-Above Operational
Cycles-Per-Hour----------------------------------------------------
Next Inspection Date (Estimated):--------------------------------------
and Flight Hours (Estimated):------------------------------------------
Magnetic Particle Inspection (MPI) Results (this inspection): Passed
______ Failed ______
If a crack is found, indicate the approximate location on the part
and the length of the crack in inches: ________________
Total Time-In-Service (TIS) (Hours):
Estimated------------------------------------------------------------
Actual---------------------------------------------------------------
Unknown--------------------------------------------------------------
At Retirement--------------------------------------------------------
Inspection results at retirement (if known):
MPI Passed ______ Failed ______
Visual Passed ______-Failed ______
Log Book Entry for Part No. ____________, Serial No. ____________,
is (date) ________, at Retirement Hours ____________. This part's
Serial No. has been marked unairworthy and unfit for further service
on (date) ____________, 199 ____.
Issued in Fort Worth, Texas, on December 13, 1995.
Daniel P. Salvano,
Manager, Rotorcraft Directorate, Aircraft Certification Service.
[FR Doc. 95-30771 Filed 12-19-95; 8:45 am]
BILLING CODE 4910-13-U
